| 1. |
- Dagar, Janardan, et al.
(författare)
-
Compositional and Interfacial Engineering Yield High-Performance and Stable p-i-n Perovskite Solar Cells and Mini-Modules
- 2021
-
Ingår i: ACS applied materials & interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 13:11, s. 13022-13033
-
Tidskriftsartikel (refereegranskat)abstract
- Through the optimization of the perovskite precursor composition and interfaces to selective contacts, we achieved a p-i-n-type perovskite solar cell (PSC) with a 22.3% power conversion efficiency (PCE). This is a new performance record for a PSC with an absorber bandgap of 1.63 eV. We demonstrate that the high device performance originates from a synergy between (1) an improved perovskite absorber quality when introducing formamidinium chloride (FACl) as an additive in the "triple cation" Cs0.05FA0.79MA0.16PbBr0.51I2.49 (Cs-MAFA) perovskite precursor ink, (2) an increased open-circuit voltage, VOC, due to reduced recombination losses when using a lithium fluoride (LiF) interfacial buffer layer, and (3) high-quality hole-selective contacts with a self-assembled monolayer (SAM) of [2-(9H-carbazol-9-yl)ethyl]phosphonic acid (2PACz) on ITO electrodes. While all devices exhibit a high performance after fabrication, as determined from current-density voltage, J-V, measurements, substantial differences in device performance become apparent when considering longer-term stability data. A reduced long-term stability of devices with the introduction of a LiF interlayer is compensated for by using FACl as an additive in the metal-halide perovskite thin-film deposition. Optimized devices maintained about 80% of the initial average PCE during maximum power point (MPP) tracking for >700 h. We scaled the optimized device architecture to larger areas and achieved fully laser patterned series-interconnected mini-modules with a PCE of 19.4% for a 2.2 cm2 active area. A robust device architecture and reproducible deposition methods are fundamental for high performance and stable large-area single junction and tandem modules based on PSCs.
|
|
| 2. |
- Kegelmann, Lukas, et al.
(författare)
-
It Takes Two to Tango - Double-Layer Selective Contacts in Perovskite Solar Cells for Improved Device Performance and Reduced Hysteresis
- 2017
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 9:20, s. 17245-17255
-
Tidskriftsartikel (refereegranskat)abstract
- Solar cells made from inorganic-organic perovskites have gradually approached market requirements as their efficiency and stability have improved tremendously in recent years. Planar low-temperature processed perovskite solar cells are advantageous for possible large-scale production but are more prone to exhibiting photocurrent hysteresis, especially in the regular n-i-p structure. Here, a systematic characterization of different electron selective contacts with a variety of chemical and electrical properties in planar n-i-p devices processed below 180 °C is presented. The inorganic metal oxides TiO2 and SnO2, the organic fullerene derivatives C60, PCBM, and ICMA, as well as double-layers with a metal oxide/PCBM structure are used as electron transport materials (ETMs). Perovskite layers deposited atop the different ETMs with the herein applied fabrication method show a similar morphology according to scanning electron microscopy. Further, surface photovoltage spectroscopy measurements indicate comparable perovskite absorber qualities on all ETMs, except TiO2, which shows a more prominent influence of defect states. Transient photoluminescence studies together with current-voltage scans over a broad range of scan speeds reveal faster charge extraction, less pronounced hysteresis effects, and higher efficiencies for devices with fullerene compared to those with metal oxide ETMs. Beyond this, only double-layer ETM structures substantially diminish hysteresis effects for all performed scan speeds and strongly enhance the power conversion efficiency up to a champion stabilized value of 18.0%. The results indicate reduced recombination losses for a double-layer TiO2/PCBM contact design: First, a reduction of shunt paths through the fullerene to the ITO layer. Second, an improved hole blocking by the wide band gap metal oxide. Third, decreased transport losses due to an energetically more favorable contact, as implied by photoelectron spectroscopy measurements. The herein demonstrated improvements of multilayer selective contacts may serve as a general design guideline for perovskite solar cells.
|
|
| 3. |
- Unger, E. L., et al.
(författare)
-
Roadmap and roadblocks for the band gap tunability of metal halide perovskites
- 2017
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 5:23, s. 11401-11409
-
Tidskriftsartikel (refereegranskat)abstract
- Solar cells based on metal-halide perovskite semiconductors inspire high hopes for efficient low cost solar cell technology. This material class exhibits a facile tunability of the band gap making them interesting for multi-junction device technology. We here compare and highlight trends in the band gap tunability and device performance metrics in reported metal halide perovskite alloys of a wide compositional range from low band gap compounds, such as FA0.75Cs0.25Sn0.5Pb0.5I3 with an absorption onset of 1.2 eV, to high bandgap compounds, such as CsPbBr3 with an absorption onset close to 2.4 eV. In between, metal halide perovskites can seemingly be seamlessly tuned by compositional engineering. However, mixed bromide-iodide compounds with band gaps above 1.7 eV often exhibit photo-induced phase segregation inducing domains with lower band gaps that emit photons of low energy. This effect also reduces the photoluminescence quantum yield and hence the maximum open circuit voltage achievable in devices. This highlight summarizes general trends for metal halide perovskites with respect to their absorption onset. Furthermore recent progress as well as possible roadblocks for the band gap tunability of metal halide perovskites are highlighted as this is of particular importance for the development of multifunction solar cell technology.
|
|
