| 1. |
- Bettini, Eleonora, et al.
(författare)
-
Study of corrosion behavior of a 22% Cr duplex stainless steel : influence of nano-sized chromium nitrides and exposure temperature
- 2013
-
Ingår i: Electrochimica Acta. - : Elsevier BV. - 0013-4686 .- 1873-3859. ; 113, s. 280-289
-
Tidskriftsartikel (refereegranskat)abstract
- Chromium nitrides may precipitate in duplex stainless steels during processing and their influence on the corrosion behavior is of great importance for the steel performance. In this study, the influence of nano-sized quenched-in chromium nitrides on the corrosion behavior of a heat treated 2205 duplex stainless steel was investigated at room temperature and 50 °C (just above critical pitting temperature). The microstructure was characterized by SEM/EDS and AFM analyses, and quenched-in nitrides precipitated in the ferrite phase were identified by TEM analysis. Volta potential mapping at room temperature suggests lower relative nobility of the ferrite matrix. Electrochemical polarization and in-situ AFM measurements in 1 M NaCl solution at room temperature show a passive behavior of the steel despite the presence of the quenched-in nitrides in the ferrite phase, and preferential dissolution of ferrite phase occurred only at transpassive conditions. At 50 °C, selective dissolution of the austenite phase was observed, while the ferrite phase with the quenched-in nitrides remained to be stable. It can be concluded that the finely dispersed quenched-in nitrides do not cause localized corrosion, whereas the exposure temperature has a strong influence on the corrosion behavior of the duplex stainless steel.
|
|
| 2. |
- Bettini, Eleonora, et al.
(författare)
-
Study of Corrosion Behavior of a 2507 Super Duplex Stainless Steel : Influence of Quenched-in and Isothermal Nitrides
- 2014
-
Ingår i: International Journal of Electrochemical Science. - 1452-3981. ; 9:1, s. 61-80
-
Tidskriftsartikel (refereegranskat)abstract
- Precipitation of different types of chromium nitrides may occur during processing of super duplex stainless steels, affecting the properties of the material. In this study the influence of quenched-in (size range ca. 50-100 nm) and isothermal (size range ca. 80-250 nm) types of nitrides on the corrosion behavior of a 2507 super duplex stainless steel has been investigated at room temperature and at 90 degrees C (above the critical pitting temperature) in 1 M NaCl solution. The microstructure has been characterized by scanning electron microscopy and magnetic force microscopy. The isothermal nitrides exhibit a higher Volta potential compared to the matrix, but such difference could not be observed for the quenched-in nitrides. In-situ electrochemical AFM measurements at room temperature show stable surfaces for a wide range of applied potentials despite the presence of either type of nitrides. In the transpassive region isothermal nitrides appear to be slightly more deleterious than quenched-in nitrides. At 90 degrees C isothermal nitrides largely reduce the corrosion resistance of the austenite phase, while the quenched-in nitrides reduce the corrosion resistance of the material to a much lesser extent. The size difference between isothermal and quenched-in chromium nitrides may be crucial, in particular above the critical pitting temperature.
|
|
| 3. |
- Cassagne, Thierry B., et al.
(författare)
-
Long term corrosion testing and monitoring of oxygen and corrosion potential in an umbilical design
- 2012
-
Ingår i: NACE - International Corrosion Conference Series. - 9781622760787 ; , s. 1096-1108
-
Konferensbidrag (refereegranskat)abstract
- Subsea umbilicals are used for control and operation of subsea oil and gas production facilities. Typically an umbilical consists of steel tubes, electrical cables, fiber optic cables, weight or strength elements and fillers. Super duplex stainless steel tube material has been used for almost 20 years within the umbilical industry. However, a recent failure on two orbital welds of 25Cr super duplex of an umbilical installed in the South China Sea was reported. From these results some umbilical end users recommended the use of thermoplastic coating to avoid crevice corrosion on 25Cr super duplex stainless steel above 20°C. However, this limit is based on results obtained for super duplex stainless steel in aerated natural seawater and very little is known on the micro-environment formed by the confined seawater between metallic tubes and polymer matrix of an umbilical. This work reports corrosion potential and oxygen content measurements in the confined zone between the metallic tubes and the polymer matrix of an umbilical. These measurements were performed using micro-electrodes on a 2 meter long real umbilical at 30°C in heated natural seawater. From the measurements, it is shown that the oxygen content in the confined zone is rapidly consumed probably due to the passive current on the stainless steel tubes and then remains below 2 ppm over one year exposure period. From the open-circuit potential measurements performed in the confined zone, it is clear that the open circuit potential remained below -150 mV/AgCl. This translates an absence of electrochemical effect of the biofilm in the confined zone. Visual and metallographic examinations of the tubes after exposure confirmed the results obtained by the microelectrodes and clearly indicate that no corrosion initiation occurred on superduplex stainless steel (base metal and welds) under these experimental conditions. The results are discussed in view of the validity of corrosion tests performed under aerated conditions and the need of further developments of new testing procedures to represent the confined situation in the umbilical design.
|
|
| 4. |
|
|
| 5. |
|
|
| 6. |
- Chai, Guocai, et al.
(författare)
-
Mechanisms of Hydrogen Induced Stress Crack Initiation and Propagation in Super Duplex Stainless Steels
- 2009
-
Ingår i: STEEL RESEARCH INTERNATIONAL. - 1611-3683. ; 80:7, s. 482-487
-
Tidskriftsartikel (refereegranskat)abstract
- Austenitic and ferritic duplex stainless steels, DSS, have recently suffered from hydrogen stress induced cracking, HISC, in subsea components with a cathodic protection. This paper provides discussions on possible HISC mechanisms. HISC initiation can occur at the ferritic grain boundaries and phase boundaries at a stress lower than the yield strength, but dominantly at phase boundaries at a stress higher than the yield strength. EBSD analysis shows that HISC in DSS results from the interaction between the dynamic plasticity by creep and hydrogen diffusion. A model on the formation of microstresses in these two phases under creep conditions is proposed, which explains why HISC occurs mainly in the ferritic phase. Discontinuous two-dimensional HISC paths were observed. The austenitic phase acts as obstacles for crack propagation. The fracture covers "valleys" and "peaks" with the cleavage ferrite and the austenite with microfacets or striations due to the hydrogen-enhanced localized-plasticity.
|
|
| 7. |
- Fuertes, Nuria
(författare)
-
Use of local electrochemical techniques for corrosion studies of stainless steels
- 2016
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The excellent corrosion resistance of stainless steels arises from the presence of a passive film on its surface. Above 10.5wt% Cr a chromium oxide of 1-3 nm is formed on the surface of the metal that in case of damage will reform and hinder further dissolution of the metal. However, the passivity of the stainless steel can be altered by material factors and external factors; such as the composition of the underlying phases, external loads or thermal treatments.In this work the local electrochemical techniques Scanning Vibrating Electrode Technique (SVET) and Scanning Kelvin Probe Force Microscopy (SKPFM) and the local characterization techniques X-ray Photoelectron Spectroscopy (XPS) and Auger Electron Spectroscopy (AES) have been used to investigate corrosion phenomena of stainless alloys based on measurements of corrosion current density, work function, thickness and composition of the oxide.The effect on work function of the thickness of the passive film and composition of the underlying phases was investigated for 301LN austenitic stainless steel (Paper I) and a heat treated superduplex 25Cr7Ni type stainless steel (Paper II). It was shown that the work function can be an indicator of corrosion resistance of the phases in the microstructure, and that the composition of the underlying phases had a greater effect on the work function than the thickness of the passive film.External factors such mechanical deformation (Paper I) and welding (Paper III) altered the passivity of the steel and work function. It was found that plastic deformation decreased irreversibly the work function, whereas elastic deformation did not have any permanent effect. Thermal oxides affected the passivity of stainless steels welded joints and were detrimental for its corrosion resistance. Anodic activity, observed with SVET, and pitting corrosion were detected at the heat tint and attributed to the interaction between the composition and the thickness of the oxide. Brushing combined with pickling was recommended for recovering the passivity of stainless steels.
|
|
| 8. |
- Kivisäkk, Ulf
(författare)
-
A test method for dewpoint corrosion of stainless steels in dilute hydrochloric acid
- 2003
-
Ingår i: Corrosion Science. - 0010-938X .- 1879-0496. ; 45:3, s. 485-495
-
Tidskriftsartikel (refereegranskat)abstract
- When acid-containing gases condense on a steel surface a phenomenon called dewpoint corrosion can occur. In this case severe attack can appear and the attack cannot be predicted from traditional immersion test data. Dewpoint corrosion can for instance be found in refinery overhead condensers and in waste incineration plants. An experimental set-up consisting of a closed glass loop has been constructed in which stainless steel samples are exposed to condensing conditions simulating a formed condensate of about 1% HCl. In the loop three stainless steels have been tested. For all three materials higher corrosion rates were found in the loop than obtained in immersion tests but in the same range as can be predicted from service experience.
|
|
| 9. |
- Kivisäkk, Ulf
(författare)
-
Corrosion testing of heat exchanger tubing
- 2003
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Heat exchanger tubes are commonly made from stainless steel.In a heat exchanger both the process fluid and the cooling orheating media can be corrosive. It is therefore important to beable to select materials that do not suffer from corrosion.Current methods in this area, however, suffer from limitationsand shortcomings. This thesis concerns corrosion tests forgeneral corrosion, dewpoint corrosion and stress corrosioncracking, respectively. For evaluation of general corrosion ofsuperduplex stainless steels in hydrochloric acid and sulphuricacid the importance of activation was studied. The results showthat activation has a great influence on the test result.Further the results indicate that experimental differences canbe the explanation for previously reported differences incorrosion resistance of superduplex stainless steel that havebeen attributed to the alloying with Cu and W. Furthermore, asimple test loop for testing stainless steels under dew formingconditions with a formed condensate of 1 % hydrochloric acidhas been developed. In the work constant strain and constantload test result have been compared and the observationsindicate that the differences can be explained by differencesin the relaxation properties of the materials.Key words:corrosion testing, heat exchanger, stainlesssteel, general corrosion, immersion tests, activation, stresscorrosion cracking, constant load, u-bends, relaxation,dewpoint corrosion
|
|
| 10. |
- Kivisäkk, Ulf, 1969-
(författare)
-
Influence of hydrogen on corrosion and stress induced cracking of stainless steel
- 2010
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Hydrogen is the smallest element in the periodical table. It has been shown in several studies that hydrogen has a large influence on the corrosion and cracking behaviour of stainless steels. Hydrogen is involved in several of the most common cathode reactions during corrosion and can also cause embrittlement in many stainless steels. Some aspects of the effect of hydrogen on corrosion and hydrogen-induced stress cracking, HISC, of stainless steels were studied in this work. These aspects relate to activation of test specimens for uniform corrosion testing, modification of a test cell for dewpoint corrosion testing and the mechanism of hydrogen-induced stress cracking. The results from uniform corrosion testing of superduplex stainless steels indicated that there is a large difference between passive and activated surfaces in hydrochloric acid and in lower concentrations of sulphuric acid. Hence, initial activation of the test specimen until hydrogen evolution can have a large influence on the results. This may provide another explanation for the differences in iso-corrosion curves for superduplex stainless steels that have previously been attributed to alloying with copper and/or tungsten. In concentrated sulphuric acid, potential oscillations were observed; these oscillations activated the specimen spontaneously. Due to these potential oscillations the influence of activation was negligible in this acid. An experimental set-up was developed for testing dewpoint corrosion of stainless steels in a condensate containing 1 % hydrochloric acid. There was an existing experimental set-up that had to be modified in order to avoid azeotroping of the water and hydrogen chloride system. A separate flask with hydro chloric acid was included in the experimental set-up. The final set-up provided reasonably good agreement with field exposures in contrary to much higher corrosion rates in the original set-up. Relaxation and low temperature creep experiments have been performed with several stainless steels in this work. The aim was to understand how creep and relaxation relates to material properties and the relative ranking between the tested materials. For low temperature creep with a load generating stresses below the yield strength, as well relaxation at stress levels above and below the yield strength, the same ranking with respect to changes in mechanical properties of the steel grades was found. For low temperature creep with a load level above the yield strength, the same ranking was not obtained. This effect can most probably be explained by annihilation and generation of dislocations. During low temperature creep above the yield strength, dislocations were generated. In addition, low temperature creep experiments were performed forone superduplex stainless steel in two different product forms with differentaustenite spacing in the microstructure. The superduplex material experienced low temperature creep at a lower load level for the material with large austenite spacing compared to the one with smaller austenite spacing. Also this differenceis influenced by dislocations. In a material with small austenite spacing the dislocations have more obstacles that they can be locked up against. Studies of the fracture surfaces of hydrogen induced stress cracking, HISC, tested duplex stainless steels showed that HISC is a hydrogen-enhanced localised plasticity, HELP, mechanism. Here a mechanism that takes into account the inhomogeneous deformation of duplex stainless steels was proposed. This mechanism involves an interaction between hydrogen diffusion and plastic straining. Due to the different mechanical properties of the phases in a superduplex stainless steel, plastic straining due to low temperature creep can occur in the softer ferrite phase. A comparison between low temperature creep data showed that for the coarser grained material, HISC occurs at the load levelwhen creep starts. However, in the sample with small austenite spacing, HISC did not occur at this load level. Microhardness measurements indicated that the hydrogen level in the ferrite was not high enough to initiate cracking in the coarser material. The proposed mechanism shows that occurrence of HISC is an interaction between local plasticity and hydrogen diffusion.
|
|
