| 1. |
- Du, Yong, et al.
(författare)
-
Investigation of the Heteroepitaxial Process Optimization of Ge Layers on Si (001) by RPCVD
- 2021
-
Ingår i: Nanomaterials. - : MDPI AG. - 2079-4991. ; 11:4
-
Tidskriftsartikel (refereegranskat)abstract
- This work presents the growth of high-quality Ge epilayers on Si (001) substrates using a reduced pressure chemical vapor deposition (RPCVD) chamber. Based on the initial nucleation, a low temperature high temperature (LT-HT) two-step approach, we systematically investigate the nucleation time and surface topography, influence of a LT-Ge buffer layer thickness, a HT-Ge growth temperature, layer thickness, and high temperature thermal treatment on the morphological and crystalline quality of the Ge epilayers. It is also a unique study in the initial growth of Ge epitaxy; the start point of the experiments includes Stranski-Krastanov mode in which the Ge wet layer is initially formed and later the growth is developed to form nuclides. Afterwards, a two-dimensional Ge layer is formed from the coalescing of the nuclides. The evolution of the strain from the beginning stage of the growth up to the full Ge layer has been investigated. Material characterization results show that Ge epilayer with 400 nm LT-Ge buffer layer features at least the root mean square (RMS) value and it's threading dislocation density (TDD) decreases by a factor of 2. In view of the 400 nm LT-Ge buffer layer, the 1000 nm Ge epilayer with HT-Ge growth temperature of 650 degrees C showed the best material quality, which is conducive to the merging of the crystals into a connected structure eventually forming a continuous and two-dimensional film. After increasing the thickness of Ge layer from 900 nm to 2000 nm, Ge surface roughness decreased first and then increased slowly (the RMS value for 1400 nm Ge layer was 0.81 nm). Finally, a high-temperature annealing process was carried out and high-quality Ge layer was obtained (TDD=2.78 x 10(7) cm(-2)). In addition, room temperature strong photoluminescence (PL) peak intensity and narrow full width at half maximum (11 meV) spectra further confirm the high crystalline quality of the Ge layer manufactured by this optimized process. This work highlights the inducing, increasing, and relaxing of the strain in the Ge buffer and the signature of the defect formation.
|
|
| 2. |
- Du, Yong, et al.
(författare)
-
Review of Highly Mismatched III-V Heteroepitaxy Growth on (001) Silicon
- 2022
-
Ingår i: Nanomaterials. - : MDPI AG. - 2079-4991. ; 12:5
-
Forskningsöversikt (refereegranskat)abstract
- Si-based group III-V material enables a multitude of applications and functionalities of the novel optoelectronic integration chips (OEICs) owing to their excellent optoelectronic properties and compatibility with the mature Si CMOS process technology. To achieve high performance OEICs, the crystal quality of the group III-V epitaxial layer plays an extremely vital role. However, there are several challenges for high quality group III-V material growth on Si, such as a large lattice mismatch, highly thermal expansion coefficient difference, and huge dissimilarity between group III-V material and Si, which inevitably leads to the formation of high threading dislocation densities (TDDs) and anti-phase boundaries (APBs). In view of the above-mentioned growth problems, this review details the defects formation and defects suppression methods to grow III-V materials on Si substrate (such as GaAs and InP), so as to give readers a full understanding on the group III-V hetero-epitaxial growth on Si substrates. Based on the previous literature investigation, two main concepts (global growth and selective epitaxial growth (SEG)) were proposed. Besides, we highlight the advanced technologies, such as the miscut substrate, multi-type buffer layer, strain superlattice (SLs), and epitaxial lateral overgrowth (ELO), to decrease the TDDs and APBs. To achieve high performance OEICs, the growth strategy and development trend for group III-V material on Si platform were also emphasized.
|
|
| 3. |
- Li, Junjie, et al.
(författare)
-
A Novel Dry Selective Isotropic Atomic Layer Etching of SiGe for Manufacturing Vertical Nanowire Array with Diameter Less than 20 nm
- 2020
-
Ingår i: Materials. - : MDPI AG. - 1996-1944. ; 13:3
-
Tidskriftsartikel (refereegranskat)abstract
- Semiconductor nanowires have great application prospects in field effect transistors and sensors. In this study, the process and challenges of manufacturing vertical SiGe/Si nanowire array by using the conventional lithography and novel dry atomic layer etching technology. The final results demonstrate that vertical nanowires with a diameter less than 20 nm can be obtained. The diameter of nanowires is adjustable with an accuracy error less than 0.3 nm. This technology provides a new way for advanced 3D transistors and sensors.
|
|
| 4. |
- Liu, Jinbiao, et al.
(författare)
-
Study of n-type doping in germanium by temperature based PF+ implantation
- 2020
-
Ingår i: Journal of materials science. Materials in electronics. - : Springer Science and Business Media LLC. - 0957-4522 .- 1573-482X. ; 31, s. 161-166
-
Tidskriftsartikel (refereegranskat)abstract
- Incorporation of P in germanium was studied by using PF+ molecular implantation in a range from room temperature to 400 °C. The presence of F acted as a barrier for P in-diffusion and resulted in higher activation of P at room temperature. In addition, it is found that when the implantation is performed at 400 °C, the residual defects are stable and the diffusion of P can be blocked during activation annealing. Therefore, the final junction depth could be well controlled by the implantation process itself. This method is meaningful for the shallow junction formation in sub 14-nm Ge-based FinFETs or high-performance photodetectors.
|
|
| 5. |
- Radamson, Henry H., et al.
(författare)
-
Miniaturization of CMOS
- 2019
-
Ingår i: Micromachines. - : MDPI AG. - 2072-666X. ; 10:5
-
Tidskriftsartikel (refereegranskat)abstract
- When the international technology roadmap of semiconductors (ITRS) started almost five decades ago, the metal oxide effect transistor (MOSFET) as units in integrated circuits (IC) continuously miniaturized. The transistor structure has radically changed from its original planar 2D architecture to today's 3D Fin field-effect transistors (FinFETs) along with new designs for gate and source/drain regions and applying strain engineering. This article presents how the MOSFET structure and process have been changed (or modified) to follow the More Moore strategy. A focus has been on methodologies, challenges, and difficulties when ITRS approaches the end. The discussions extend to new channel materials beyond the Moore era.
|
|
| 6. |
- Radamson, Henry H., et al.
(författare)
-
State of the Art and Future Perspectives in Advanced CMOS Technology
- 2020
-
Ingår i: Nanomaterials. - : MDPI AG. - 2079-4991. ; 10:8
-
Forskningsöversikt (refereegranskat)abstract
- The international technology roadmap of semiconductors (ITRS) is approaching the historical end point and we observe that the semiconductor industry is driving complementary metal oxide semiconductor (CMOS) further towards unknown zones. Today's transistors with 3D structure and integrated advanced strain engineering differ radically from the original planar 2D ones due to the scaling down of the gate and source/drain regions according to Moore's law. This article presents a review of new architectures, simulation methods, and process technology for nano-scale transistors on the approach to the end of ITRS technology. The discussions cover innovative methods, challenges and difficulties in device processing, as well as new metrology techniques that may appear in the near future.
|
|
| 7. |
- Wang, Guilei, et al.
(författare)
-
Growth of SiGe layers in source and drain regions for 10 nm node complementary metal-oxide semiconductor (CMOS)
- 2020
-
Ingår i: Journal of materials science. Materials in electronics. - : Springer Science and Business Media LLC. - 0957-4522 .- 1573-482X. ; 31, s. 26-33
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, the integration of Si 1−x Ge x (50% ≤ x ≤ 60%) selective epitaxy on source/drain regions in 10 nm node FinFET has been presented. One of the major process issues was the sensitivity of Si-fins’ shape to ex- and in-situ cleaning prior to epitaxy. For example, the sharpness of Si-fins could easily be damaged during the wafer washing. The results showed that a DHF dip before the normal cleaning, was essential to clean the Si-fins while in-situ annealing in range of 780–800 °C was needed to remove the native oxide for high epitaxial quality. Because of smallness of fins, the induced strain by SiGe could not be directly measured by X-ray beam in a typical XRD tool in the lab or even in a Synchrotron facility. Further analysis using nano-beam diffraction technique in high-resolution transmission electron microscope also failed to provide information about strain in the FinFET structure. Therefore, the induced strain by SiGe was simulated by technology computer-aided design program and the Ge content was measured by using energy dispersive spectroscopy. Simulation results showed 0.8, 1 and 1.3 GPa for Ge content of 40%, 50% and 60%, respectively. A kinetic gas model was also introduced to predict the SiGe profile on Si-fins with sharp triangular shape. The input parameters in the model includes growth temperature, partial pressure of the reactant gases and the exposed Si coverage in the chip area.
|
|
