| 1. |
- Laptev, Roman, et al.
(författare)
-
Influence of beam current on microstructure of electron beam melted Ti-6Al-4V alloy
- 2019
-
Ingår i: Progress in Natural Science. - : Elsevier BV. - 1002-0071 .- 1745-5391. ; 29:4, s. 440-446
-
Tidskriftsartikel (refereegranskat)abstract
- The defect microstructure of the samples manufactured from Ti-6Al-4V powder was studied using electron beam melting (EBM) in the beam current range of 17 - 13 mA. The hybrid digital complex combined positron lifetime spectroscopy and coincidence Doppler broadening spectroscopy was used to characterize the defect structure of the materials. The microstructure and defects were also analyzed by transmission electron microscopy. It has been established that the main type of the defects in the EBM manufactured samples is dislocations. According to the conducted measurements and calculations, the dislocation density in the EBM manufactured samples exceeds by two orders the similar value for the cast Ti-6Al-4Valloy. Formation of Ti-Ti-Al nanoscale clusters has been found in the EBM manufactured samples.
|
|
| 2. |
- Botero, Carlos Alberto, et al.
(författare)
-
Microstructural and mechanical evaluation of a cr-mo-v cold-work tool steel produced via electron beam melting (Ebm)
- 2021
-
Ingår i: Materials. - : MDPI AG. - 1996-1944. ; 14:11
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, a highly alloyed cold work tool steel, Uddeholm Vanadis 4 Extra, was manufactured via the electron beam melting (EBM) technique. The corresponding material microstructure and carbide precipitation behavior as well as the microstructural changes after heat treatment were characterized, and key mechanical properties were investigated. In the as-built condition, the mi-crostructure consists of a discontinuous network of very fine primary Mo-and V-rich carbides dispersed in an auto-tempered martensite matrix together with ≈15% of retained austenite. Adjusted heat treatment procedures allowed optimizing the microstructure by the elimination of Mo-rich carbides and the precipitation of fine and different sized V-rich carbides, along with a decrease in the retained austenite content below 2%. Hardness response, compressive strength, and abrasive wear properties of the EBM-manufactured material are similar or superior to its as-HIP forged counterparts manufactured using traditional powder metallurgy route. In the material as built by EBM, an impact toughness of 16–17 J was achieved. Hot isostatic pressing (HIP) was applied in order to further increase ductility and to investigate its impact upon the microstructure and properties of the material. After HIPing with optimized protocols, the ductility increased over 20 J.
|
|
| 3. |
- Botero, Carlos Alberto, et al.
(författare)
-
Microstructure and nanomechanical behavior of modified 316L-based materials fabricated using EBM
- 2018
-
Konferensbidrag (refereegranskat)abstract
- Stainless steel 316L based materials modified by the additions of iron-based wear-resistant alloys (Colferoloy@ 103 and 139) used for thermal spray coatings applications were fabricated by EBM. Process parameters were tailored to fabricate compact specimens of 1cm3 in an Arcam A2 (Arcam AB, Mölndal, Sweden) at Mid Sweden University. Microstructural features of the materials obtained were characterized by OM and SEM in polished and etched samples. Nanoindentation tests carried out at different penetration depths were performed on selected areas of the polished specimens to evaluate the materials micro/nano mechanical behavior and to establish correlations with the observed microstructure.
|
|
| 4. |
|
|
| 5. |
- Botero, Carlos, et al.
(författare)
-
Functionally Graded Steels Obtained via Electron Beam Powder Bed Fusion
- 2023
-
Ingår i: Key Engineering Materials. - : Trans Tech Publications, Ltd.. - 1013-9826 .- 1662-9795. ; 964, s. 79-84
-
Tidskriftsartikel (refereegranskat)abstract
- Electron-Beam Powder Bed Fusion (EB-PBF) is one of the most important metal additive manufacturing (AM) technologies. In EB-PBF, a focused electron beam is used to melt metal powders in a layer by layer approach. In this investigation two pre-alloyed steel-based powders, stainless steel 316L and V4E, a tool steel developed by Uddeholm, were used to manufacture functionally graded materials. In the proposed approach two powders are loaded into the feeding container, V4E powder on top of 316L one, preventing their mixing. Such type of feeding yields components with two distinct materials separated by a zone with gradual transition from 316L to V4E. Microstructure and local mechanical properties were evaluated in the manufactured samples. Optical Microscopy, Scanning Electron Microscopy and EDX on the polished cross-sections show a gradual microstructural and compositional transition from characteristic 316L at the bottom of the specimens to the tool steel towards the top. Nanoindentation experiments confirmed a consequent gradient in hardness and elastic modulus, which gradually increase towards the top surface of the samples. The achieved results provide great possibilities to tailor the composition, microstructure, mechanical properties, and wear resistance by combining different powders in the powder bed AM technology. Potential applications include the tooling industry, where hard and wear-resistant materials are demanded on the surface with tougher and more ductile materials in the core of the tool.
|
|
| 6. |
- Bujtar, Peter, et al.
(författare)
-
Emerging manufacturing bioengineering technologies 2: Scaffold designing experiment using titanium scaffolds
- 2014
-
Ingår i: British Journal of Oral & Maxillofacial Surgery. - : Elsevier BV. - 0266-4356 .- 1532-1940. ; 52:8, s. e60-e61
-
Tidskriftsartikel (refereegranskat)abstract
- Substantial volume defects of the head and neck oftenrequire customized solutions to improve quality of life likefree flap transfers.Titanium and its alloys are versatile materialsproviding the feature of osteointegration. The conditionswhich facilitate the deposition of lamellar bone are underextensive research. Our project aimed to determine whethertitanium can function as a scaffold - unlike simple plates - toenhance bone regeneration for load bearing structures. Thereaction of stem cells to scaffolds with varying stiffness willbe presented.Additive manufacturing were used to produce a variety ofscaffolds to optimize titanium structures. Electric beam melting(EBM) manufacturing allowed us to optimize the elasticmodulus (Young) of the titanium to match with cadaveric bone from a previous project. Multidirectional mechanicaltests were performed on the various designs of titanium cellstructures (n=80). The predictability and quality of manufacturingwas assessed statistically and also with scanningelectron microscope (SEM).The results demonstrated structures matching the mechanicalproperties of bone and even anisotropy as our resultssuggest 3GPa elasticity. This allows the possibility to buildregenerating bone with predictable properties. In addition,predictable patterning - unlike etching and sandblasting - ofmicroscopic (nano) features found to be significant and nonhomogenous simple repetitive patterns provide better cellularresponse.The benefit that tissue engineering techniques offer isdecreased morbidity, relative independence from donor site,with a highly specific and customized shape. Titanium basedreconstruction constructs seems to offer an alternative futurefor bony reconstruction.
|
|
| 7. |
|
|
| 8. |
- Bäckström, Mikael, et al.
(författare)
-
Sports Technology Education at Mid Sweden University
- 2013
-
Ingår i: 6TH ASIA-PACIFIC CONGRESS ON SPORTS TECHNOLOGY (APCST). - : Elsevier. ; , s. 214-219
-
Konferensbidrag (refereegranskat)abstract
- In present paper we would like to share some experiences of building new education in Sports Technology at MidSweden University and the results of 10 years of successfully running it in Östersund. The Sports Technologyeducation at Mid Sweden University started at Campus Östersund in 2003 as a part of the curriculum of theEngineering Department. This specialization was initially at the three-year Bachelor level, and later it was extendedto an additional two-year Master level. Aiming at the quality of Sports Technology education, three keystones areunderlying its process, representing the solid knowledge base, capacity to be flexible in problem solving and the usean innovative approaches. The Department unites researches with a background in both natural sciences andengineering disciplines, having a wide experience of working with and within the industry, equally active in researchand teaching. The unique constellation of the profiles forming the Department include not only the SportsTech®group, being “the backbone”, but also the Ecology and Eco-technology, and Quality Technology groups bringing theexcellence and extra competence needed to assure the quality of the Sports Technology education. We were the firsthigher education institution in Sweden to give this kind of education program and now some other SwedishUniversities have followed us. Our success can be measured by a number of graduates taking good jobs in theindustry. We also enjoy a steady flow of new students coming from all parts of Sweden, and Sports Technologyeducation stays among the most desirable ones in the country.
|
|
| 9. |
- Chudinova, E., et al.
(författare)
-
Functionalization of additive-manufactured Ti6Al4V scaffolds with poly(allylamine hydrochloride)/poly(styrene sulfonate) bilayer microcapsule system containing dexamethasone
- 2021
-
Ingår i: Materials Chemistry and Physics. - : Elsevier BV. - 0254-0584 .- 1879-3312. ; 273
-
Tidskriftsartikel (refereegranskat)abstract
- Porous titanium alloy Ti6Al4V scaffolds manufactured via electron beam melting (EBM®) reveal broad prospects for applications in bone tissue engineering. However, local inflammation and even implant failure may occur while placing an implant into the body. Thus, the application of drug carriers to the surface of a metallic implant can provide treatment at the inflammation site. In this study, we propose to use polyelectrolyte (PE) microcapsules formed by layer-by-layer (LbL) synthesis loaded with both porous calcium carbonate (CaCO3) microparticles and the anti-inflammatory drug dexamethasone (DEX) to functionalize implant surfaces and achieve controlled drug release. Scanning electron microscopy indicated that the CaCO3 microparticles coated with PE bilayers loaded with DEX had a spherical shape with a diameter of 2.3 ± 0.2 μm and that the entire scaffold surface was evenly coated with the microcapsules. UV spectroscopy showed that LbL synthesis allows the manufacturing of microcapsules with 40% DEX. According to high performance liquid chromatography (HPLC) analysis, 80% of the drug was released within 24 h from the capsules consisting of three bilayers of polystyrene sulfonate (PSS) and poly(allylamine)hydrochloride (PAH). The prepared scaffolds functionalized with CaCO3 microparticles loaded with DEX and coated with PE bilayers showed hydrophilic surface properties with a water contact angle below 5°. Mouse embryonic fibroblast cells were seeded on Ti6Al4V scaffolds with and without LbL surface modification. The surface modification with LbL PE microcapsules with CaCO3 core affected cell morphology in vitro. The results confirmed that DEX had no toxic effect and did not prevent cell adhesion and spreading, thus no cytotoxic effect was observed, which will be further studied in vivo.
|
|
| 10. |
|
|
