| 1. |
- Brezinsek, S., et al.
(författare)
-
Erosion, screening, and migration of tungsten in the JET divertor
- 2019
-
Ingår i: Nuclear Fusion. - : IOP PUBLISHING LTD. - 0029-5515 .- 1741-4326. ; 59:9
-
Tidskriftsartikel (refereegranskat)abstract
- The erosion of tungsten (W), induced by the bombardment of plasma and impurity particles, determines the lifetime of plasma-facing components as well as impacting on plasma performance by the influx of W into the confined region. The screening of W by the divertor and the transport of W in the plasma determines largely the W content in the plasma core, but the W source strength itself has a vital impact on this process. The JET tokamak experiment provides access to a large set of W erosion-determining parameters and permits a detailed description of the W source in the divertor closest to the ITER one: (i) effective sputtering yields and fluxes as function of impact energy of intrinsic (Be, C) and extrinsic (Ne, N) impurities as well as hydrogenic isotopes (H, D) are determined and predictions for the tritium (T) isotope are made. This includes the quantification of intra- and inter-edge localised mode (ELM) contributions to the total W source in H-mode plasmas which vary owing to the complex flux compositions and energy distributions in the corresponding phases. The sputtering threshold behaviour and the spectroscopic composition analysis provides an insight in the dominating species and plasma phases causing W erosion. (ii) The interplay between the net and gross W erosion source is discussed considering (prompt) re-deposition, thus, the immediate return of W ions back to the surface due to their large Larmor radius, and surface roughness, thus, the difference between smooth bulk-W and rough W-coating components used in the JET divertor. Both effects impact on the balance equation of local W erosion and deposition. (iii) Post-mortem analysis reveals the net erosion/deposition pattern and the W migration paths over long periods of plasma operation identifying the net W transport to remote areas. This W transport is related to the divertor plasma regime, e.g. attached operation with high impact energies of impinging particles or detached operation, as well as to the applied magnetic configuration in the divertor, e.g. close divertor with good geometrical screening of W or open divertor configuration with poor screening. JET equipped with the ITER-like wall (ILW) provided unique access to the net W erosion rate within a series of 151 subsequent H-mode discharges (magnetic field: B-t = 2.0 T, plasma current: I-p = 2.0 MA, auxiliary power P-aux = 12 MW) in one magnetic configuration accumulating 900 s of plasma with particle fluences in the range of 5-6 x 10(26) D(+ )m(-2) in the semi-detached inner and attached outer divertor leg. The comparison of W spectroscopy in the intra-ELM and inter-ELM phases with post-mortem analysis of W marker tiles provides a set of gross and net W erosion values at the outer target plate. ERO code simulations are applied to both divertor leg conditions and reproduce the erosion/deposition pattern as well as confirm the high experimentally observed prompt W re-deposition factors of more than 95% in the intra- and inter-ELM phase of the unseeded deuterium H-mode plasma. Conclusions to the expected divertor conditions in ITER as well as to the JET operation in the DT plasma mixture are drawn on basis of this unique benchmark experiment.
|
|
| 2. |
- Heinola, K., et al.
(författare)
-
Long-term fuel retention in JET ITER-like wall
- 2016
-
Ingår i: Physica Scripta. - : Institute of Physics Publishing (IOPP). - 0031-8949 .- 1402-4896. ; T167
-
Tidskriftsartikel (refereegranskat)abstract
- Post-mortem studies with ion beam analysis, thermal desorption, and secondary ion mass spectrometry have been applied for investigating the long-term fuel retention in the JET ITERlike wall components. The retention takes place via implantation and co-deposition, and the highest retention values were found to correlate with the thickness of the deposited impurity layers. From the total amount of retained D fuel over half was detected in the divertor region. The majority of the retained D is on the top surface of the inner divertor, whereas the least retention was measured in the main chamber on the mid-plane of the inner wall limiter. The recessed areas of the inner wall showed significant contribution to the main chamber total retention. Thermal desorption spectroscopy analysis revealed the energetic T from DD reactions being implanted in the divertor. The total T inventory was assessed to be >0.3 mg.
|
|
| 3. |
- Widdowson, A., et al.
(författare)
-
Overview of fuel inventory in JET with the ITER-like wall
- 2017
-
Ingår i: Nuclear Fusion. - : Institute of Physics Publishing (IOPP). - 0029-5515 .- 1741-4326. ; 57:8
-
Tidskriftsartikel (refereegranskat)abstract
- Post mortem analyses of JET ITER-Like-Wall tiles and passive diagnostics have been completed after each of the first two campaigns (ILW-1 and ILW-2). They show that the global fuel inventory is still dominated by co-deposition; hence plasma parameters and sputtering processes affecting material migration influence the distribution of retained fuel. In particular, differences between results from the two campaigns may be attributed to a greater proportion of pulses run with strike points in the divertor corners, and having about 300 discharges in hydrogen at the end of ILW-2. Recessed and remote areas can contribute to fuel retention due to the larger areas involved, e.g. recessed main chamber walls, gaps in castellated Be main chamber tiles and material migration to remote divertor areas. The fuel retention and material migration due to the bulk W Tile 5 during ILW-1 are presented. Overall these tiles account for only a small percentage of the global accountancy for ILW-1.
|
|
| 4. |
- Widdowson, A., et al.
(författare)
-
Overview of the JET ITER-like wall divertor
- 2017
-
Ingår i: Nuclear Materials and Energy. - : ELSEVIER. - 2352-1791. ; 12, s. 499-505
-
Tidskriftsartikel (refereegranskat)abstract
- The work presented draws on new analysis of components removed following the second JET ITER-like wall campaign 2013-14 concentrating on the upper inner divertor, inner and outer divertor corners, lifetime issues relating to tungsten coatings on JET carbon fibre composite divertor tiles and dust/particulate generation. The results show that the upper inner divertor remains the region of highest deposition in the JET-ILW. Variations in plasma configurations between the first and second campaign have altered material migration to the corners of the inner and outer divertor. Net deposition is shown to be beneficial in the sense that it reduces W coating erosion, covers small areas of exposed carbon surfaces and even encapsulates particles. (C) 2017 Elsevier Ltd. This is an open access article under the CC BY-NC-ND license.
|
|
| 5. |
- Brezinsek, S., et al.
(författare)
-
Beryllium migration in JET ITER-like wall plasmas
- 2015
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 55:6
-
Tidskriftsartikel (refereegranskat)abstract
- JET is used as a test bed for ITER, to investigate beryllium migration which connects the lifetime of first-wall components under erosion with tokamak safety, in relation to long-term fuel retention. The (i) limiter and the (ii) divertor configurations have been studied in JET-ILW (JET with a Be first wall and W divertor), and compared with those for the former JET-C (JET with carbon-based plasma-facing components (PFCs)). (i) For the limiter configuration, the Be gross erosion at the contact point was determined in situ by spectroscopy as between 4% (E-in = 35 eV) and more than 100%, caused by Be self-sputtering (E-in = 200 eV). Chemically assisted physical sputtering via BeD release has been identified to contribute to the effective Be sputtering yield, i.e. at E-in = 75 eV, erosion was enhanced by about 1/3 with respect to the bare physical sputtering case. An effective gross yield of 10% is on average representative for limiter plasma conditions, whereas a factor of 2 difference between the gross erosion and net erosion, determined by post-mortem analysis, was found. The primary impurity source in the limiter configuration in JET-ILW is only 25% higher (in weight) than that for the JET-C case. The main fraction of eroded Be stays within the main chamber. (ii) For the divertor configuration, neutral Be and BeD from physically and chemically assisted physical sputtering by charge exchange neutrals and residual ion flux at the recessed wall enter the plasma, ionize and are transported by scrape-off layer flows towards the inner divertor where significant net deposition takes place. The amount of Be eroded at the first wall (21 g) and the Be amount deposited in the inner divertor (28 g) are in fair agreement, though the balancing is as yet incomplete due to the limited analysis of PFCs. The primary impurity source in the JET-ILW is a factor of 5.3 less in comparison with that for JET-C, resulting in lower divertor material deposition, by more than one order of magnitude. Within the divertor, Be performs far fewer re-erosion and transport steps than C due to an energetic threshold for Be sputtering, and inhibits as a result of this the transport to the divertor floor and the pump duct entrance. The target plates in the JET-ILW inner divertor represent at the strike line a permanent net erosion zone, in contrast to the net deposition zone in JET-C with thick carbon deposits on the CFC (carbon-fibre composite) plates. The Be migration identified is consistent with the observed low long-term fuel retention and dust production with the JET-ILW.
|
|
| 6. |
- Krat, S., et al.
(författare)
-
Comparison of erosion and deposition in JET divertor during the first three ITER-like wall campaigns
- 2020
-
Ingår i: Physica Scripta. - : IOP PUBLISHING LTD. - 0031-8949 .- 1402-4896. ; T171:1
-
Tidskriftsartikel (refereegranskat)abstract
- The manuscript presents an overview of the erosion and deposition data in the inner and outer JET divertor observed during the first three ITER-like wall campaigns (JET-ILW1, JET-ILW2, JET-ILW3). Erosion and deposition were studied using core samples cut out from divertor tiles. For the studied samples a similar general deposition pattern was observed in all three campaigns: More than 60% of the total deposition occurred in the upper region of the inner divertor on tiles 0 and 1, where Be was transported and deposited from the scrape-off layer. High erosion was observed only on tile 5. In JET-ILW2 and 3, erosion together with high power fluxes was observed in the outer divertor at the bottom of tile 7. Additionally, deposition peaks were observed on the sloping parts of tiles 4 and 6, which were more pronounced in JET-ILW2 and 3 due to placing the strike point more often on these tiles. The deposits consisted primarily of Be, with some additional D and C. Deposition rates were observed to decrease from campaign to campaign, with the C deposition rate decreasing the most, more than 2 times from JET-ILW1 to JET-ILW3. D retention up to levels of similar to 1 at% was observed up to large depths in the W protective coatings in all campaigns.
|
|
| 7. |
- Krat, S., et al.
(författare)
-
Erosion at the inner wall of JET during the discharge campaign 2013-2014
- 2017
-
Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 11, s. 20-24
-
Tidskriftsartikel (refereegranskat)abstract
- The erosion of Be and W marker layers was investigated using long-term samples containing marker layers during the second ITER-like wall discharge campaign 2013-2014 (ILW-2). The samples were mounted in Be coated Inconel tiles between the inner wall guard limiters (IWGL). They were analyzed using elastic backscattering (EBS) before and after exposure. All samples showed noticeable erosion. The results were compared to the data for Be and W erosion rates for the first 2011-2012 JET ITER-like wall (ILW-1) campaign, and to the data for C erosion during the 2005-2009 campaign when JET was operated with a carbon wall. The mean W erosion rates and the toroidal and poloidal distributions of the W erosion were nearly the same for the ILW-1 and ILW-2 campaigns. The mean erosion rate of Be during the ILW-2 campaign was smaller by a factor of about two compared to the ILW-1 campaign.
|
|
| 8. |
- Mayer, M., et al.
(författare)
-
Erosion and deposition in the JET divertor during the first ILW campaign
- 2016
-
Ingår i: Physica Scripta. - : Institute of Physics Publishing (IOPP). - 0031-8949 .- 1402-4896. ; T167
-
Tidskriftsartikel (refereegranskat)abstract
- Erosion and deposition were studied in the JET divertor during the first JET ITER-like wall campaign 2011 to 2012 using marker tiles. An almost complete poloidal section consisting of tiles 0, 1, 3, 4, 6, 7, 8 was studied. The data from divertor tile surfaces were completed by the analysis of samples from remote divertor areas and from the inner wall cladding. The total mass of material deposited in the divertor decreased by a factor of 4-9 compared to the deposition of carbon during all-carbon JET operation before 2010. Deposits in 2011 to 2012 consist mainly of beryllium with 5-20 at.% of carbon and oxygen, respectively, and small amounts of Ni, Cr, Fe and W. This decrease of material deposition in the divertor is accompanied by a decrease of total deuterium retention inside the JET vessel by a factor of 10 to 20. The detailed erosion/deposition pattern in the divertor with the ITER-like wall configuration shows rigorous changes compared to the pattern with the all-carbon JET configuration.
|
|
| 9. |
- Krat, S., et al.
(författare)
-
Beryllium film deposition in cavity samples in remote areas of the JET divertor during the 2011-2012 ITER-like wall campaign
- 2017
-
Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 12, s. 548-552
-
Tidskriftsartikel (refereegranskat)abstract
- Beryllium film deposition was studied with cavity samples in remote areas of the inner and outer JET divertor and below divertor tile 5 during the 2011-2012 campaign with the ITER-like wall. Predominantly beryllium films were formed inside the cavities with some additional carbon, the ratio Be/C was > 2. These deposited layers had high D/(Be+C) ratios of about 0.3. The formation of these films is mainly due to sticking of beryllium-containing particles with low sticking coefficients < 0.5. The observed surface loss probabilities depend on the position in the divertor. The particles responsible for film deposition originated from the location of in the divertor strike points.
|
|
| 10. |
- Krat, S., et al.
(författare)
-
Erosion at the inner wall of JET during the discharge campaign 2011-2012 in comparison with previous campaigns
- 2015
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 456, s. 106-110
-
Tidskriftsartikel (refereegranskat)abstract
- The erosion of Be and W marker layers was investigated using long-term samples during the first ITER-like wall discharge campaign 2011-2012. The markers were mounted in Be coated Inconel tiles between the inner wall guard limiters (IWGL). They were analyzed using Rutherford backscattering (RBS) before and after exposure. All samples showed strong erosion. The results were compared to the data for Be and W erosion rates for the 2005-2009 and the 2001-2004 campaigns, respectively, when JET was operated with a carbon wall. In 2005-2009 Be and C samples were used, and W samples were used in 2001-2004. The mean W erosion rates and the toroidal and poloidal distributions of the W erosion were the same for the 2001-2004 and the 2011-2012 campaigns. The mean erosion rate of Be during the 2011-2012 campaign was smaller by a factor of about two compared to the 2005-2009 campaign and showed a different poloidal distribution. The mean erosion rate of the inner JET ITER-like wall was about 4-5 times smaller than the mean erosion rate of the carbon wall.
|
|
