| 1. |
- Li, Danqin, et al.
(författare)
-
n-Doping of photoactive layer in binary organic solar cells realizes over 18.3% efficiency
- 2022
-
Ingår i: Nano Energy. - : ELSEVIER. - 2211-2855 .- 2211-3282. ; 96
-
Tidskriftsartikel (refereegranskat)abstract
- Electronic doping of conjugated semiconductor plays a critical role in the fabrication of high efficiency organic optoelectronic devices. Here, we report an organic solar cell (OSC) by doping n-type DMBI-BDZC into one host binary bulk heterojunction (BHJ) photoactive layer comprised of a polymer donor PM6 and a nonfullerene acceptor Y6. The resulting champion device yields a significantly improved power conversion efficiency from 17.17% to 18.33% with an impressive fill factor of 80.20%. It is found that the electrically doped photoactive layer exhibits enhanced and balanced charge carrier mobilities, more effective exciton dissociation, longer carrier lifetime, and suppressed charge recombination with smaller energy loss. The dopant molecule DMBIBDZC also act as a surface morphology modifier of the photoactive layer with enhanced charge transport. This work demonstrates that manipulation of charge transport via adding a low concentration dopant into photoactive layer is a promising approach for further improvement of BHJ OSC performance.
|
|
| 2. |
- Liu, Tiefeng, et al.
(författare)
-
Ground-state electron transfer in all-polymer donor:acceptor blends enables aqueous processing of water-insoluble conjugated polymers
- 2023
-
Ingår i: Nature Communications. - : NATURE PORTFOLIO. - 2041-1723. ; 14:1
-
Tidskriftsartikel (refereegranskat)abstract
- Water-based conductive inks are vital for the sustainable manufacturing and widespread adoption of organic electronic devices. Traditional methods to produce waterborne conductive polymers involve modifying their backbone with hydrophilic side chains or using surfactants to form and stabilize aqueous nanoparticle dispersions. However, these chemical approaches are not always feasible and can lead to poor material/device performance. Here, we demonstrate that ground-state electron transfer (GSET) between donor and acceptor polymers allows the processing of water-insoluble polymers from water. This approach enables macromolecular charge-transfer salts with 10,000x higher electrical conductivities than pristine polymers, low work function, and excellent thermal/solvent stability. These waterborne conductive films have technological implications for realizing high-performance organic solar cells, with efficiency and stability superior to conventional metal oxide electron transport layers, and organic electrochemical neurons with biorealistic firing frequency. Our findings demonstrate that GSET offers a promising avenue to develop water-based conductive inks for various applications in organic electronics. Chemical approaches to improve aqueous dispersions of conjugated polymers are limited by the feasibility of modifying the backbone or lead to poor performance. Here, Liu et al. show that ground-state electron transfer in donor:acceptor blends aids aqueous dispersion, for high conductivity and solubility.
|
|
| 3. |
- Berggren, Elin, et al.
(författare)
-
Charge Transfer in the P(g42T-T) : BBL Organic Polymer Heterojunction Measured with Core-Hole Clock Spectroscopy
- 2023
-
Ingår i: The Journal of Physical Chemistry C. - : American Chemical Society (ACS). - 1932-7447 .- 1932-7455. ; 127:49, s. 23733-23742
-
Tidskriftsartikel (refereegranskat)abstract
- The conductivity of organic polymer heterojunction devices relies on the electron dynamics occurring along interfaces between the acceptor and donor moieties. To investigate these dynamics with chemical specificity, spectroscopic techniques are employed to obtain localized snapshots of the electron behavior at selected interfaces. In this study, charge transfer in blends (by weight 10, 50, 90, and 100%) of p-type polymer P(g(4)2T-T) (bithiophene-thiophene) and n-type polymer BBL (poly(benzimidazo-benzo-phenanthroline)) was measured by resonant Auger spectroscopy. Electron spectra emanating from the decay of core-excited states created upon X-ray absorption in the donor polymer P(g(4)2T-T) were measured in the sulfur KL2,3L2,3 Auger kinetic energy region as a function of the excitation energy. By tuning the photon energy across the sulfur K-absorption edge, it is possible to differentiate between decay paths in which the core-excited electron remained on the atom with the core-hole and those where it tunneled away. Analyzing the competing decay modes of these localized and delocalized (charge-transfer) processes facilitated the computation of charge-transfer times as a function of excitation energy using the core-hole clock method. The electron delocalization times derived from the measurements were found to be in the as/fs regime for all polymer blends, with the fastest charge transfer occurring in the sample with an equal amount of donor and acceptor polymer. These findings highlight the significance of core-hole clock spectroscopy as a chemically specific tool for examining the local charge tunneling propensity, which is fundamental to understanding macroscopic conductivity. Additionally, the X-ray absorption spectra near the sulfur K-edge in the P(g(4)2T-T) polymer for different polymer blends were analyzed to compare molecular structure, orientation, and ordering in the polymer heterojunctions. The 50% donor sample exhibited the most pronounced angular dependence of absorption, indicating a higher level of ordering compared to the other weight blends. Our studies on the electron dynamics of this type of all-polymer donor-acceptor systems, in which spontaneous ground-state electron transfer occurs, provide us with critical insights to further advance the next generation of organic conductors with mixed electron-hole conduction characteristics suitable for highly stable electrodes of relevance for electronic, electrochemical, and optoelectronic applications.
|
|
| 4. |
- Craighero, Mariavittoria, 1995, et al.
(författare)
-
Poly(benzodifurandione) Coated Silk Yarn for Thermoelectric Textiles
- 2024
-
Ingår i: Advanced Science. - 2198-3844 .- 2198-3844. ; In Press
-
Tidskriftsartikel (refereegranskat)abstract
- Thermoelectric textile devices represent an intriguing avenue for powering wearable electronics. The lack of air-stable n-type polymers has, until now, prevented the development of n-type multifilament yarns, which are needed for textile manufacturing. Here, the thermomechanical properties of the recently reported n-type polymer poly(benzodifurandione) (PBFDO) are explored and its suitability as a yarn coating material is assessed. The outstanding robustness of the polymer facilitates the coating of silk yarn that, as a result, displays an effective bulk conductivity of 13 S cm−1, with a projected half-life of 3.2 ± 0.7 years at ambient conditions. Moreover, the n-type PBFDO coated silk yarn with a Young's modulus of E = 0.6 GPa and a strain at break of εbreak = 14% can be machine washed, with only a threefold decrease in conductivity after seven washing cycles. PBFDO and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) coated silk yarns are used to fabricate two out-of-plane thermoelectric textile devices: a thermoelectric button and a larger thermopile with 16 legs. Excellent air stability is paired with an open-circuit voltage of 17 mV and a maximum output power of 0.67 µW for a temperature difference of 70 K. Evidently, PBFDO coated multifilament silk yarn is a promising component for the realization of air stable thermoelectric textile devices.
|
|
| 5. |
- Huang, Xiaofeng, et al.
(författare)
-
Solvent racing crystallization : Low-solvation dispersion cosolvents for high-quality halide perovskites in photovoltaics
- 2023
-
Ingår i: Joule. - : Elsevier. - 2542-4351. ; 7:7, s. 1556-1573
-
Tidskriftsartikel (refereegranskat)abstract
- The solvation capacity of dispersion solvents plays a crucial role in the solution processing of metal halide perovskites. For instance, N,N-dimethylformamide (DMF), a widely used dispersion solvent, possesses high solvation capacity but often generates suboptimal film quality due to slow crystallization kinetics. We propose using low-solvation binary cosolvents (nitrile-and ether-type solvents) to achieve a balance between solvation (i.e., sufficient solubility of precursors) and desolvation (i.e., rapid crystallization of films) pro-cesses during perovskite synthesis. The polarity and hydrogen -bonding property of these cosolvents synergistically enhance their solvation capacity, facilitating perovskite precursor dissolution. Moreover, the low-solvation cosolvents accelerate the crystalliza-tion of well-defined intermediate films, yielding higher-quality pe-rovskites than those synthesized with DMF. The optimized modules achieved an active-area efficiency of 22.27%, with a certified aper-ture-area efficiency of 16.10% and corresponding active-area effi-ciency of 20.75%. This research on solvation regulation provides universal guidelines for innovatively preparing high-quality halide perovskites.
|
|
| 6. |
|
|
| 7. |
- Li, Qifan, et al.
(författare)
-
A Highly Conductive n-Type Conjugated Polymer Synthesized in Water
- 2024
-
Ingår i: Journal of the American Chemical Society. - : AMER CHEMICAL SOC. - 0002-7863 .- 1520-5126.
-
Tidskriftsartikel (refereegranskat)abstract
- Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is a benchmark hole-transporting (p-type) polymer that finds applications in diverse electronic devices. Most of its success is due to its facile synthesis in water, exceptional processability from aqueous solutions, and outstanding electrical performance in ambient. Applications in fields like (opto-)electronics, bioelectronics, and energy harvesting/storage devices often necessitate the complementary use of both p-type and n-type (electron-transporting) materials. However, the availability of n-type materials amenable to water-based polymerization and processing remains limited. Herein, we present a novel synthesis method enabling direct polymerization in water, yielding a highly conductive, water-processable n-type conjugated polymer, namely, poly[(2,2 '-(2,5-dihydroxy-1,4-phenylene)diacetic acid)-stat-3,7-dihydrobenzo[1,2-b:4,5-b ']difuran-2,6-dione] (PDADF), with remarkable electrical conductivity as high as 66 S cm(-1), ranking among the highest for n-type polymers processed using green solvents. The new n-type polymer PDADF also exhibits outstanding stability, maintaining 90% of its initial conductivity after 146 days of storage in air. Our synthetic approach, along with the novel polymer it yields, promises significant advancements for the sustainable development of organic electronic materials and devices.
|
|
| 8. |
- Pataki, Nathan James, et al.
(författare)
-
A Rolled Organic Thermoelectric Generator with High Thermocouple Density
- 2024
-
Ingår i: Advanced Functional Materials. - : WILEY-V C H VERLAG GMBH. - 1616-301X .- 1616-3028.
-
Tidskriftsartikel (refereegranskat)abstract
- The surge in the number of distributed microelectronics and sensors requires versatile, scalable, and affordable power sources. Heat-harvesting organic thermoelectric generators (TEGs) are regarded as potential key components of the future energy landscape. Recent advances in the performance of organic thermoelectric materials have made practical applications of organic TEGs more feasible than ever before, yet the challenges of designing and fabricating organic TEGs suitable for real scenarios are scarcely addressed. Specifically, small sensors and wearables demand for micro-thermoelectric generators (mu TEGs) with high power density architectures and small form factors, while typical demonstrations of organic TEGs are characterized by < 10 thermocouples (TCs) per cm(2). This work presents a rolled, organic mu TEG architecture combining large-area, solution-based deposition techniques, such as inkjet and spray-coating, and an ultrathin parylene substrate to achieve a thermocouple density of 1842 TCs cm(-2). Such demonstrative mu TEG reaches a thermoelectric conversion performance of 0.15 mu W cm(-2) at Delta T = 50 K. Such power output is well in line with finite element method simulations, which highlight the benefit of the architecture and show that remarkable power densities, in the mW cm(-2) range at Delta T = 10 K, are realistically achievable with geometrical improvements and already ongoing advancements in organic thermoelectric inks.
|
|
| 9. |
- Wu, Hanyan, et al.
(författare)
-
Influence of Molecular Weight on the Organic Electrochemical Transistor Performance of Ladder-Type Conjugated Polymers
- 2022
-
Ingår i: Advanced Materials. - : Wiley-V C H Verlag GMBH. - 0935-9648 .- 1521-4095. ; 34:4
-
Tidskriftsartikel (refereegranskat)abstract
- Organic electrochemical transistors (OECTs) hold promise for developing a variety of high-performance (bio-)electronic devices/circuits. While OECTs based on p-type semiconductors have achieved tremendous progress in recent years, n-type OECTs still suffer from low performance, hampering the development of power-efficient electronics. Here, it is demonstrated that fine-tuning the molecular weight of the rigid, ladder-type n-type polymer poly(benzimidazobenzophenanthroline) (BBL) by only one order of magnitude (from 4.9 to 51 kDa) enables the development of n-type OECTs with record-high geometry-normalized transconductance (g(m,norm) approximate to 11 S cm(-1)) and electron mobility x volumetric capacitance (mu C* approximate to 26 F cm(-1) V-1 s(-1)), fast temporal response (0.38 ms), and low threshold voltage (0.15 V). This enhancement in OECT performance is ascribed to a more efficient intermolecular charge transport in high-molecular-weight BBL than in the low-molecular-weight counterpart. OECT-based complementary inverters are also demonstrated with record-high voltage gains of up to 100 V V-1 and ultralow power consumption down to 0.32 nW, depending on the supply voltage. These devices are among the best sub-1 V complementary inverters reported to date. These findings demonstrate the importance of molecular weight in optimizing the OECT performance of rigid organic mixed ionic-electronic conductors and open for a new generation of power-efficient organic (bio-)electronic devices.
|
|
| 10. |
- Wu, Hanyan, et al.
(författare)
-
Stable organic electrochemical neurons based on p-type and n-type ladder polymers
- 2023
-
Ingår i: Materials Horizons. - : ROYAL SOC CHEMISTRY. - 2051-6347 .- 2051-6355. ; :10, s. 4213-4223
-
Tidskriftsartikel (refereegranskat)abstract
- Organic electrochemical transistors (OECTs) are a rapidly advancing technology that plays a crucial role in the development of next-generation bioelectronic devices. Recent advances in p-type/n-type organic mixed ionic-electronic conductors (OMIECs) have enabled power-efficient complementary OECT technologies for various applications, such as chemical/biological sensing, large-scale logic gates, and neuromorphic computing. However, ensuring long-term operational stability remains a significant challenge that hinders their widespread adoption. While p-type OMIECs are generally more stable than n-type OMIECs, they still face limitations, especially during prolonged operations. Here, we demonstrate that simple methylation of the pyrrole-benzothiazine-based (PBBT) ladder polymer backbone results in stable and high-performance p-type OECTs. The methylated PBBT (PBBT-Me) exhibits a 25-fold increase in OECT mobility and an impressive 36-fold increase in & mu;C* (mobility x volumetric capacitance) compared to the non-methylated PBBT-H polymer. Combining the newly developed PBBT-Me with the ladder n-type poly(benzimidazobenzophenanthroline) (BBL), we developed complementary inverters with a record-high DC gain of 194 V V-1 and excellent stability. These state-of-the-art complementary inverters were used to demonstrate leaky integrate-and-fire type organic electrochemical neurons (LIF-OECNs) capable of biologically relevant firing frequencies of about 2 Hz and of operating continuously for up to 6.5 h. This achievement represents a significant improvement over previous results and holds great potential for developing stable bioelectronic circuits capable of in-sensor computing.
|
|
