| 1. |
- Banerjee, Debashree, et al.
(författare)
-
Electrical tuning of radiative cooling at ambient conditions
- 2023
-
Ingår i: Cell Reports Physical Science. - : ELSEVIER. - 2666-3864. ; 4:2
-
Tidskriftsartikel (refereegranskat)abstract
- Passive radiative cooling forms a sustainable means for cooling of objects through thermal radiation. Along with progress on static cooling systems, there is an emerging need for dynamic control to enable thermoregulation. Here, we demonstrate temperature regu-lation of devices at ambient pressure and temperature by electri-cally tuning their radiative cooling power. Our concept exploits the possibility to electrochemically tune the thermal emissivity and thereby cooling power of a conducting polymer, which enabled reversible control of device temperatures of around 0.25 degrees C at ambient conditions in a sky simulator. Besides tuneable radiative cooling by exposure to the sky, the concept could also contribute to reduced needs for indoor climate control by enabling dynamic control of thermal energy flows between indoor objects, such as be-tween people and walls.
|
|
| 2. |
- Liao, Mingna, et al.
(författare)
-
Cellulose-Based Radiative Cooling and Solar Heating Powers Ionic Thermoelectrics
- 2023
-
Ingår i: Advanced Science. - : WILEY. - 2198-3844. ; 10:8
-
Tidskriftsartikel (refereegranskat)abstract
- Cellulose opens for sustainable materials suitable for radiative cooling thanks to inherent high thermal emissivity combined with low solar absorptance. When desired, solar absorptance can be introduced by additives such as carbon black. However, such materials still shows high thermal emissivity and therefore performs radiative cooling that counteracts the heating process if exposed to the sky. Here, this is addressed by a cellulose-carbon black composite with low mid-infrared (MIR) emissivity and corresponding suppressed radiative cooling thanks to a transparent IR-reflecting indium tin oxide coating. The resulting solar heater provides opposite optical properties in both the solar and thermal ranges compared to the cooler material in the form of solar-reflecting electrospun cellulose. Owing to these differences, exposing the two materials to the sky generated spontaneous temperature differences, as used to power an ionic thermoelectric device in both daytime and nighttime. The study characterizes these effects in detail using solar and sky simulators and through outdoor measurements. Using the concept to power ionic thermoelectric devices shows thermovoltages of >60 mV and 10 degrees C temperature differences already at moderate solar irradiance of approximate to 400 W m(-2).
|
|
| 3. |
- Liao, Mingna, et al.
(författare)
-
Solar Heating Modulated by Evaporative Cooling Provides Intermittent Temperature Gradients for Ionic Thermoelectric Supercapacitors
- 2024
-
Ingår i: Advanced Functional Materials. - : WILEY-V C H VERLAG GMBH. - 1616-301X .- 1616-3028.
-
Tidskriftsartikel (refereegranskat)abstract
- Solar heating is important for many applications but less attractive for concepts requiring intermittent heating, such as ionic thermoelectric supercapacitors (ITESCs). However, the heating process even at constant solar illumination can be converted to temperature oscillations through water infiltration and evaporation. Here, this process is demonstrated for a carbon nanotube-cellulose membrane and used to induce temporally varying temperature gradients across an ITESC, which enables continuous operation through repeated charge and discharge cycles. A temperature variation of 10 K can be generated on the top electrode, which leads to a variation in the temperature difference across the ITESC of 7.5 K. Precise control over charge and discharge durations can be achieved by adjusting the volume and interval of the added water. The concept of temporarily adjusting temperatures by evaporative cooling may be extended to create intermittent heating also for other heat sources that are typically constant. A vertical ionic thermoelectric supercapacitor (ITESC) is driven by intermittent temperature gradients as induced by constant solar heating and periodic evaporative cooling. As shown, a solar absorber provides temperature oscillations on the top electrodes through water infiltration and evaporation. This concept enables continuous operation of ITESCs through repeated charge and discharge cycles. image
|
|
| 4. |
- Sultana, Ayesha, et al.
(författare)
-
The Origin of Thermal Gradient-Induced Voltage in Polyelectrolytes
- 2023
-
Ingår i: Small. - : WILEY-V C H VERLAG GMBH. - 1613-6810 .- 1613-6829.
-
Tidskriftsartikel (refereegranskat)abstract
- Ionic thermoelectric materials can generate large thermal voltages under temperature gradients while also being low-cost and environmentally friendly. Many electrolytes with large Seebeck coefficients are reported in recent years, however, the mechanism of the thermal voltage is remained elusive. In this work, three types of polyelectrolytes are studied with different cations and identified a significant contribution to their thermal voltage originating from a concentration gradient. This conclusion is based on studies of the loss and gain of water upon temperature changes, variations in conductivity with water content and temperature, and the voltages induced by changes in water content. The results are analyzed by the "hopping mode" dynamics of charge transport in electrolytes. The hydration of different cations influences the water concentration gradient, which affects the barrier height and ion-induced potential in the electrodes. This work shows that the hydro-voltage in ionic thermoelectric devices can be one order of magnitude larger than the contribution from thermodiffusion-induced potentials, and becomes the main contributor to energy harvesting when implemented into ionic thermoelectric supercapacitors. Together with the rationalized theoretical discussion, this work clarifies the mechanism of thermal voltages in electrolytes and provides a new path for the development of ionic thermoelectric materials. The thermal voltage of polyelectrolyte films largely depends on the water concentration gradient under a temperature difference, which can be optimized to promote the generated total voltage up to over 30 mV K-1.image
|
|
| 5. |
- Zhang, Qilun, 1992-, et al.
(författare)
-
Industrial Kraft Lignin Based Binary Cathode Interface Layer Enables Enhanced Stability in High Efficiency Organic Solar Cells
- 2023
-
Ingår i: Advanced Materials. - : WILEY-V C H VERLAG GMBH. - 0935-9648 .- 1521-4095.
-
Tidskriftsartikel (refereegranskat)abstract
- Herein, a binary cathode interface layer (CIL) strategy based on the industrial solvent fractionated LignoBoost kraft lignin (KL) is adopted for fabrication of organic solar cells (OSCs). The uniformly distributed phenol moieties in KL enable it to easily form hydrogen bonds with commonly used CIL materials, i.e., bathocuproine (BCP) and PFN-Br, resulting in binary CILs with tunable work function (WF). This work shows that the binary CILs work well in OSCs with large KL ratio compatibility, exhibiting equivalent or even higher efficiency to the traditional CILs in state of art OSCs. In addition, the combination of KL and BCP significantly enhanced OSC stability, owing to KL blocking the reaction between BCP and nonfullerene acceptors (NFAs). This work provides a simple and effective way to achieve high-efficient OSCs with better stability and sustainability by using wood-based materials. This work introduces industrial solvent fractionated LignoBoost kraft lignin (KL) in highly efficient organic solar cells (OSCs) by binary cathode interface layer (CIL) strategy, which can significantly improve the stability of both binary and ternary photoactive layer (PAL) OSC, owing to the passivation of diffusion and reaction between bathocuproine (BCP) and nonfullerene acceptors (NFAs). The results combine sustainable wood-based material with classic interface materials in advance NFA-OSCs.image
|
|
