| 1. |
-
- 2019
-
Tidskriftsartikel (refereegranskat)
|
|
| 2. |
- Liu, Jiandong, et al.
(författare)
-
An Improved ångström-type model for estimating solar radiation over the tibetan plateau
- 2017
-
Ingår i: Energies. - : MDPI AG. - 1996-1073. ; 10:7
-
Tidskriftsartikel (refereegranskat)abstract
- © 2017 by the authors. For estimating the annual mean of daily solar irradiation in plateau mountainous regions, observed data from 15 radiation stations were used to validate different empirical estimation methods over the Tibetan Plateau. Calibration indicates that sunshine-based site-dependent models perform better than temperature-based ones. Then, the highly rated sunshine-based Ångström model and temperature-based Bristow model were selected for regional application. The geographical models perform much better than the average models, but still not ideally. To achieve better performance, the Ångström-type model was improved using altitude and water vapor pressure as the leading factors. The improved model can accurately predict the coefficients at all the stations, and performs the best among all models with an average Nash-Sutcliffe Efficiency value of 0.856. Spatial distribution of the annual mean of daily solar irradiation was then estimated with the improved model. It is indicated that there is an increasing trend of radiation from east to west, with a great center of the annual mean of daily solar irradiation on southwest Tibetan Plateau ranging from 20 to 24 MJm2. The improved model should be further validated against observations before its applications in other plateau mountainous regions.
|
|
| 3. |
- Liu, Jiandong, et al.
(författare)
-
Observation and calculation of the solar radiation on the Tibetan Plateau
- 2012
-
Ingår i: Energy Conversion and Management. - : Elsevier BV. - 0196-8904. ; 57, s. 23-32
-
Tidskriftsartikel (refereegranskat)abstract
- Distribution of solar radiation is vital to locate the most suitable regions for harvesting solar energy, but solar radiation is only observed at few stations due to high costs and difficult maintenance. From 2001 to 2005, a set of pyranometer instruments were set up in Gaize, on the Tibetan Plateau, to test the hypothesis of high solar-radiation levels in this region, and find a suitable method for estimating the radiation. Over the 5-year observation period, the average daily radiation was 21 MJ m-2day-1 with maximum daily values of 27 MJ m-2day-1 occurring in June and minimum values of 14 MJ m-2day-1 in December, which is much higher than those measured in other regions at similar latitudes. The observational data were used to validate a set of radiation models: five sunshine based and three temperature based. The results showed that of the five sunshine-based models, a newly developed “comprehensive” model performed the best, but that the “vapor revised Angstrom model” was recommended to use for its simplicity and easy operation. The temperature-based models performed worse than the sunshine-based ones, where the Wu model is to be preferred if a temperature-based model is the only option. Moreover, it was shown that when estimating the solar radiation based on time-dependent coefficients, consideration of the seasonal variation of the coefficients has little predictive value and is thus unnecessary. Based on the results of this study, a strategy for the calculation of solar radiation on the Tibetan Plateau was made for potential users.
|
|
| 4. |
- Bao, Haiyan, et al.
(författare)
-
Condition of setting surge tanks in hydropower plants - A review
- 2018
-
Ingår i: Renewable & sustainable energy reviews. - : Elsevier BV. - 1364-0321 .- 1879-0690. ; 81, s. 2059-2070
-
Forskningsöversikt (refereegranskat)abstract
- Hydropower plays an important role in the safe, stable and efficient operation of power systems, especially with current trends toward renewable energy systems. The total global potential of gross, technical, economic, and exploitable hydropower are still enormous in the future, and the developments of new hydropower stations (HPSs) are of great importance. For constructions of new HPSs, the condition of setting surge tanks (CSST) is crucial for various perspectives, e.g. safety, stability and economy of HPSs. In this review, the CSST are summarized and analyzed from the three aspects: regulation assurance, operation stability, and the regulation quality, with an aim of providing a reference and guidance for research and engineering applications regarding surge tanks. Upstream and downstream surge tanks in conventional HPSs and pumped storage power stations are all included. Moreover, a comprehensive comparison of CSST under different conditions is conducted. One of the main focuses of this review is on Chinese studies, for introducing many meaningful results written in Chinese to more readers all over the world.
|
|
| 5. |
- Cai, Jing, et al.
(författare)
-
Influence of organic aerosol molecular composition on particle absorptive properties in autumn Beijing
- 2022
-
Ingår i: Atmospheric Chemistry And Physics. - : Copernicus GmbH. - 1680-7316 .- 1680-7324. ; 22:2, s. 1251-1269
-
Tidskriftsartikel (refereegranskat)abstract
- Organic aerosol (OA) is a major component of fine particulate matter (PM), affecting air quality, human health, and the climate. The absorptive and reflective behavior of OA components contributes to determining particle optical properties and thus their effects on the radiative budget of the troposphere. There is limited knowledge on the influence of the molecular composition of OA on particle optical properties in the polluted urban environment. In this study, we characterized the molecular composition of oxygenated OA collected on filter samples in the autumn of 2018 in Beijing, China, with a filter inlet for gases and aerosols coupled to a high-resolution time-of-flight chemical ionization mass spectrometer (FIGAERO–CIMS). Three haze episodes occurred during our sampling period with daily maximum concentrations of OA of 50, 30, and 55 µg m−3. We found that the signal intensities of dicarboxylic acids and sulfur-containing compounds increased during the two more intense haze episodes, while the relative contributions of wood-burning markers and other aromatic compounds were enhanced during the cleaner periods. We further assessed the optical properties of oxygenated OA components by combining detailed chemical composition measurements with collocated particle light absorption measurements. We show that light absorption enhancement (Eabs) of black carbon (BC) was mostly related to more oxygenated OA (e.g., dicarboxylic acids), likely formed in aqueous-phase reactions during the intense haze periods with higher relative humidity, and speculate that they might contribute to lensing effects. Aromatics and nitro-aromatics (e.g., nitrocatechol and its derivatives) were mostly related to a high light absorption coefficient (babs) consistent with light-absorbing (brown) carbon (BrC). Our results provide information on oxygenated OA components at the molecular level associated with BrC and BC particle light absorption and can serve as a basis for further studies on the effects of anthropogenic OA on radiative forcing in the urban environment.
|
|
| 6. |
- Cai, Jing, et al.
(författare)
-
Influence of organic aerosol molecular composition on particle absorptive properties in autumn Beijing
- 2022
-
Ingår i: Atmospheric Chemistry and Physics. - 1680-7316 .- 1680-7324. ; 22, s. 1251-1269
-
Tidskriftsartikel (refereegranskat)abstract
- Organic aerosol (OA) is a major component of fine particulate matter (PM), affecting air quality, human health, and the climate. The absorptive and reflective behavior of OA components contributes to determining particle optical properties and thus their effects on the radiative budget of the troposphere. There is limited knowledge on the influence of the molecular composition of OA on particle optical properties in the polluted urban environment. In this study, we characterized the molecular composition of oxygenated OA collected on filter samples in the autumn of 2018 in Beijing, China, with a filter inlet for gases and aerosols coupled to a high-resolution time-of-flight chemical ionization mass spectrometer (FIGAERO-CIMS). Three haze episodes occurred during our sampling period with daily maximum concentrations of OA of 50, 30, and 55 μg m-3. We found that the signal intensities of dicarboxylic acids and sulfur-containing compounds increased during the two more intense haze episodes, while the relative contributions of wood-burning markers and other aromatic compounds were enhanced during the cleaner periods. We further assessed the optical properties of oxygenated OA components by combining detailed chemical composition measurements with collocated particle light absorption measurements. We show that light absorption enhancement (Eabs) of black carbon (BC) was mostly related to more oxygenated OA (e.g., dicarboxylic acids), likely formed in aqueous-phase reactions during the intense haze periods with higher relative humidity, and speculate that they might contribute to lensing effects. Aromatics and nitro-aromatics (e.g., nitrocatechol and its derivatives) were mostly related to a high light absorption coefficient (babs) consistent with light-absorbing (brown) carbon (BrC). Our results provide information on oxygenated OA components at the molecular level associated with BrC and BC particle light absorption and can serve as a basis for further studies on the effects of anthropogenic OA on radiative forcing in the urban environment. Copyright:
|
|
| 7. |
- Liu, Jiandong, et al.
(författare)
-
Changes in the relationship between solar radiation and sunshine duration in large cities of China
- 2015
-
Ingår i: Energy. - : Elsevier BV. - 0360-5442. ; 82, s. 589-600
-
Tidskriftsartikel (refereegranskat)abstract
- Based on the linear relationship between solar radiation and sunshine duration, the Angstrom model is widely used to estimate solar radiation from routinely observed meteorological variables for energy exploitation. However, the relationship may have changed in quickly developing regions in the recent decades under global "dimming" and "brightening" context, with increasing aerosols due to industrial pollutions. Solar radiation stations under different climate conditions in six large cities in China are selected to test this hypothesis. Analysis of the related meteorological items shows that Guiyang has the lowest solar radiation with the average annual value of 10.5 MJm(-2)d(-1), while Lhasa on the Tibetan Plateau has the highest of 20.1 MJm(-2)d(-1). Both radiation and sunshine hours decreased from 1961 to 2010, but at different rates. A moving linear regression method is used to investigate the changes in the relationship between radiation and sunshine duration, the results indicate an abrupt change in the correlation coefficients in 1980-1990s, which can be attributed to the aerosol load resulting from air pollution caused by the industrial development in 1980s under China's Open Door Policy. The sky condition has been changing from clean to dirty, thus the relationship between solar radiation and duration changes in the 1980's and has recovered in the recent decades. This finding implies that it might not necessarily be right to use long data sets for model calibration. Further investigation confirms that the Angstrom model performs the best with higher NSE (nash-sutcliffe efficiency) of 0.914 and lower MAPE (mean absolute percentage error) and RMSE (root mean square error) values of 13.7 w/m(2) and 23.9 w/m(2) respectively, when calibrated with a 10-year data set. In contrast, the model performs worst when it is calibrated with a 40-year data set, with NSE, MAPE and RMSE values of 0.891, 15.1 w/m(2) and 25.3 w/m(2), respectively. Based on the findings of this research, a 10-year data set is recommended as the national standard for model calibration in rapidly developing regions of China. Further analogous investigations are needed in other industrial regions to make an international standard for Angstrom model calibration. (C) 2015 Elsevier Ltd. All rights reserved.
|
|
| 8. |
- Wang, Jiandong, et al.
(författare)
-
Synthesis, microstructure and properties of MoSi2-5vol.%Al2O3 composites
- 2014
-
Ingår i: Ceramics International. - : Elsevier BV. - 0272-8842 .- 1873-3956. ; 40:10 Part B, s. 16381-16387
-
Tidskriftsartikel (refereegranskat)abstract
- MoSi2-5vol.%Al2O3 composites were prepared in situ by self-propagating combustion synthesis from Mo, Si, Al and MoO3 powders. The combustion mode and temperature of the self-propagating reaction and phase composition of the product were investigated. The results showed that the combustion mode was a steady-state self-propagating process and the composite product was composed of MoSi2 and Al2O3. MoSi2-5vol.%Al2O3 composites were consolidated by vacuum hot-pressed sintering from 1300 to 1600 °C to produce composites with high density. MoSi2-5vol.%Al2O3 composites sintered at 1400 °C exhibited a fine microstructure and excellent mechanical properties: grain size ∼5 μm, Vicker’s hardness 11.14 GPa, bending strength 435 MPa, and fracture toughness 4.53 MPa.m1/2.
|
|
| 9. |
- Xu, Weidong, et al.
(författare)
-
Precisely Controlling the Grain Sizes with an Ammonium Hypophosphite Additive for High-Performance Perovskite Solar Cells
- 2018
-
Ingår i: Advanced Functional Materials. - : WILEY-V C H VERLAG GMBH. - 1616-301X .- 1616-3028. ; 28:33
-
Tidskriftsartikel (refereegranskat)abstract
- A facile approach to precisely control the perovskite grain sizes is proposed and demonstrated for high-performance photovoltaic (PV) solar cells. With the introduction of various amounts of NH4H2PO2 (AHP) additives into the PbI2/CH3NH3I precursors, the grain scale of CH3NH3PbI3 films can be finely turned from hundreds of nanometer to micrometer scale, allowing evaluating the effects of crystalline grain boundary on trap densities, charge recombination, and PV device performance. The X-ray diffraction and X-ray photoelectron spectroscopy measurements indicate that the formation of intermediates plays a key role in assisting the perovskite crystal growth. The optimized devices show much larger open-circuit voltages (V-OC) up to 1.10 +/- 0.02 V and significantly enhance power conversion efficiencies (PCEs) of 16.5 +/- 0.7%, as compared to the control devices with PCE of 9.4 +/- 1.0% and V-OC of 1.00 +/- 0.03 V. Further investigations confirm that the boosted PV performance origins from the decreased defect densities due to enlarged grain sizes. It is also demonstrated that the approach is general and applicable to other perovskite systems, e.g., HC(NH2)(2)PbI3. The results suggest the promising application of AHP in achieving high-performance perovskite PV devices, and shed light on understanding the grain boundary effects on perovskite optoelectronics.
|
|
| 10. |
- Zhang, Tianji, et al.
(författare)
-
In-depth characterization of 1,4-butanediol diglycidyl ether substituted hyaluronic acid hydrogels
- 2023
-
Ingår i: Carbohydrate Polymers. - : Elsevier. - 0144-8617 .- 1879-1344. ; 307
-
Tidskriftsartikel (refereegranskat)abstract
- BDDE substituted HA hydrogels remain the most commonly used HA product in the biomedical field. The physical and biochemical properties of the hydrogels are dependent on the degree of modification and substitution patterns/positions, thus, characterizing their fine structure is of great importance for quality assurance. In this study, we developed novel LC-MS methods for accurate determination of MoD as well as in-depth characterization of the linkage network. Fragments resulted from enzymatic depolymerization were resolved by a porous graphitic carbon column followed by online tandem-MS for determining the modification site/residue. With high-resolution separation, two types of previously unknown structures were detected in the cross-linked fragments of 2-B-2 and 4-B-2. Based on the feature of resistance to NaBH4 reduction, these structures contain a GlcNAc residue modified at OH1. This special sugar unit likely derived from reducing end of the native polysaccharide could be a signature to discriminate subtle batch to batch variations.
|
|
