| 1. |
- Pantazis, N, et al.
(författare)
-
Determining the likely place of HIV acquisition for migrants in Europe combining subject-specific information and biomarkers data
- 2019
-
Ingår i: Statistical methods in medical research. - : SAGE Publications. - 1477-0334 .- 0962-2802. ; 28:7, s. 1979-1997
-
Tidskriftsartikel (refereegranskat)abstract
- In most HIV-positive individuals, infection time is only known to lie between the time an individual started being at risk for HIV and diagnosis time. However, a more accurate estimate of infection time is very important in certain cases. For example, one of the objectives of the Advancing Migrant Access to Health Services in Europe (aMASE) study was to determine if HIV-positive migrants, diagnosed in Europe, were infected pre- or post-migration. We propose a method to derive subject-specific estimates of unknown infection times using information from HIV biomarkers’ measurements, demographic, clinical, and behavioral data. We assume that CD4 cell count (CD4) and HIV-RNA viral load trends after HIV infection follow a bivariate linear mixed model. Using post-diagnosis CD4 and viral load measurements and applying the Bayes’ rule, we derived the posterior distribution of the HIV infection time, whereas the prior distribution was informed by AIDS status at diagnosis and behavioral data. Parameters of the CD4–viral load and time-to-AIDS models were estimated using data from a large study of individuals with known HIV infection times (CASCADE). Simulations showed substantial predictive ability (e.g. 84% of the infections were correctly classified as pre- or post-migration). Application to the aMASE study ( n = 2009) showed that 47% of African migrants and 67% to 72% of migrants from other regions were most likely infected post-migration. Applying a Bayesian method based on bivariate modeling of CD4 and viral load, and subject-specific information, we found that the majority of HIV-positive migrants in aMASE were most likely infected after their migration to Europe.
|
|
| 2. |
|
|
| 3. |
|
|
| 4. |
- Polimeni, A., et al.
(författare)
-
Hydrogen related effects in diluted nitrides
- 2003
-
Ingår i: 22nd Int. Conf. on Defects in Semiconductors,2003. - : Elsevier. ; , s. 371-
-
Konferensbidrag (refereegranskat)abstract
- Hydrogen irradiation leads to the passivation of the electronic activity of nitrogen in Ga(AsN), thus allowing a fine tuning of the material optical properties. Here, some recent results on the effects that hydrogen irradiation has on the electronic properties of diluted III-N-V alloys are presented. In Ga(AsN), both the increase in the electron effective mass and exciton wave function localization induced by nitrogen are reversed in a fully controllable manner by hydrogen irradiation. In Ga(PN), hydrogen widens the band gap and exposes gradually in the gap nitrogen complex states formerly resonant with the conduction band.
|
|
| 5. |
- Dyal Ukabhai, K., et al.
(författare)
-
Formation of Ti2Cu in Ti-Cu Alloys
- 2022
-
Ingår i: JOURNAL OF PHASE EQUILIBRIA AND DIFFUSION. - : Springer Nature. - 1547-7037 .- 1863-7345. ; 43:3, s. 332-344
-
Tidskriftsartikel (refereegranskat)abstract
- One of the major issues with dental implants is failure due to bacterial infection, and additions of copper are known to improve the antimicrobial properties of Ti alloys. There are inconsistencies in the Ti rich area of the Cu-Ti binary phase diagram, hence the need to find out if Ti2Cu or Ti3Cu is formed, and to identify the type of formation of Ti2Cu. Four alloys: 20, 33, 40 and 50 Cu (mass%) were produced by arc melting and studied using SEM, XRD and DSC. The reactions were derived, and the temperatures of the reactions were determined by DSC. The formation of Ti2Cu is congruent, and no Ti3Cu was found.
|
|
| 6. |
- Masia, NDE, et al.
(författare)
-
Corrosion performance of Ti-Cu alloys targeted for biomedical applications
- 2022
-
Ingår i: Suid-Afrikaanse tydskrif vir natuurwetenskap en tegnologie. - : Medpharm Publications. - 0254-3486 .- 2222-4173. ; 40:1, s. 244-250
-
Tidskriftsartikel (refereegranskat)abstract
- The Thermo-Calc™ program and TTTI3 database were used to predict the phases in Ti-Cu with 5, 25, and 40 wt% Cu. Based on the predicted results, experimental work was conducted and the Ti-Cu alloys were produced in a button arc furnace, and characterised in the as-cast and the annealed condition (900°C) followed by water quenching. Microstructures and compositions were determined using an electron probe micro-analyser, and the phases were identified by X-ray diffraction. The corrosion performance was measured by potentiodynamic polarisation in a phosphate buffered saline solution at 37 °C at 7.4 pH while purging with nitrogen gas. The Ti-5Cu and Ti-25Cu alloys comprised (αTi) and Ti2Cu phases, the Ti-40Cu alloy comprised Ti2Cu and TiCu. Although the addition of copper decreased the corrosion performance by down to 75%, the corrosion rates were still within the acceptable range (0.02-0.13 mm/y) for biocompatibility of metallic implants. Annealing at 900 °C did not improve the corrosion performance.
|
|
