| 1. |
- Mazaheri, Ava, 1992-
(författare)
-
Beyond the Force: Redefining load exposure assessments of nutrunners for improved power tool ergonomics
- 2023
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Reaction force exposure from handheld tightening tools (also known as nutrunners) constitutes an acknowledged contributor to musculoskeletal disorders among assembly operators, and are today not regulated by explicit limits. The research presented in this thesis aimed at contributing to the development of recommended exposure limits for, and assessments of, reaction loads from handheld right-angle and pistol-grip tightening tools.In order to address the thesis objectives, four research studies were conducted. A literature review was conducted to provide an overview of the current state of knowledge within the topic area. Knowledge gaps were identified by mapping available publications and based on those suggesting directions for further research. Thereafter, two psychophysically based experimental studies were conducted where acceptability limits related to load exposure from handheld tightening tools were derived for right-angle and pistol-grip tightening tools. Finally, an automotive manufacturer’s approach to evaluating and managing the use of handheld tightening tools was outlined by means of an interview study.As found through the literature review, four of the forty included publications had stated exposure limits (general recommendations) or acceptability limits (load acceptance as assessed by study participants) for reaction load exposure from handheld tightening tools. However, some of the reported limits did not consider relevant physical parameters, and some did not comply with modern power tool technologies. Based on this, it was suggested that researchers should emphasize physical quantities relevant to the reaction load such as impulse, express exposure limits in terms of reaction load relevant parameters (and not only the tightening torque), and further study modern power tool technologies.The experimental studies resulted in acceptability limits for right-angle and pistol-grip tightening tools expressed as screw-joint tightening torque (i.e. a task-related factor), where acceptable tightening torque limits were higher for the inertia-controlled tightening program compared to the continuous drive tightening program, in both studies. In addition, corresponding acceptable reaction load levels (i.e. the exposure) were derived, indicating load levels resulting from the tool use that the study participants assessed as acceptable for an 8-hour workday. It should be noted that the experimental times on which the acceptability limits are based were limited, and that the acceptability limits therefore should not be prescribed to full workdays.From the interview study, three main topic categories were identified based on the interviewees’ responses: ‘A holistic approach’, ‘Information and knowledge availability’ and ‘Negotiating criteria’. Within the studied automotive organization, a comprehensive approach to ergonomics assessments is incorporate, where both objective and subjective evaluations form the basis for addressing physically demanding tool use situations. Further, it was found that there are different instances where the employees lack sufficient knowledge related to the tools, and which can influence the employment of handheld tightening tools. In addition, it was found that criteria such as safety and quality could in some situations compete with ergonomics efforts. In conclusion, the findings from this thesis can contribute to the development of recommended exposure limits and evaluation methods for reaction load exposure from handheld tightening tools. Policymakers could utilize the insights presented in this thesis to form general guidelines directed at power tool manufacturers as well as tool using organizations. Through standardized guidelines, reaction loads from handheld tightening tools, which is one of the contributors to MSDs within assembly work, can be managed and reduced.
|
|
| 2. |
|
|
| 3. |
- Mazaheri, Ava, et al.
(författare)
-
Reaction force exposure for tightening tool users : A psychophysical based experimental study of electric right-angle nutrunners
- 2022
-
Ingår i: Applied Ergonomics. - : Elsevier BV. - 0003-6870 .- 1872-9126. ; 103
-
Tidskriftsartikel (refereegranskat)abstract
- Reaction forces from nutrunner tools constitute a risk of developing MSDs. However, recommendations for sustainable reaction force levels are lacking. The aim of this study was to inform recommendations regarding reaction load exposures from right-angle nutrunners. Through a psychophysics approach, experienced assembly workers subjectively assessed reaction loads when using a nutrunner in six combinations of tool tightening strategy, work-pace and screw-joint stiffness. Electromyography, tool and joint parameters were measured. Regardless of tightening strategy, joint stiffness and work-pace combinations, no large differences in acceptable tightening torque, peak reaction force, and handle displacement were observed. However, acceptable jerk and impulse differed substantially between the TurboTight (R) (high-acceleration) and QuickStep (R) (conventional) tightening strategies. Although the TurboTight (R) strategy overall showed reduced peak muscular activities compared to the QuickStep (R), the participant-rated acceptable torque levels were similar, plausibly due to TurboTights' high jerk levels. Jerk and impulse are hypothesized to influence the perception of reaction loads.
|
|
| 4. |
|
|
| 5. |
- Mazaheri, Ava, et al.
(författare)
-
Reaction load exposure from handheld powered tightening tools : A scoping review
- 2021
-
Ingår i: International Journal of Industrial Ergonomics. - : Elsevier BV. - 0169-8141 .- 1872-8219. ; 81
-
Tidskriftsartikel (refereegranskat)abstract
- Assembly workers using handheld powered tightening tools are repetitively subjected to reaction loads resulting from the tool handle. Despite the vast amount of research, tool manufacturers and OSH practitioners still lack well-grounded recommendations and benchmarks for ergonomics evaluations of reaction loads. This review provides an overview of research investigating reaction loads and operator physical demand, and identifies gaps in current means of evaluating reaction load exposure from tightening tools. A scoping review was conducted, scanning for quantifications of reaction loads as well as reported indications of MSD risks following tightening tool use. Suggested maximum exposures for reaction loads were further identified. The most commonly investigated quantities among the 40 publications included, were peak reaction force/torque (70%) and handle displacement (70%), followed by impulse (23%). Pneumatic tools were studied at greater extent (65%) than electric tools (30%). Three studies presented a relationship between reaction load exposure and physiological changes, i.e. edema, tissue oxygenation and blood volume changes, indicating an elevated risk of developing MSDs. Four publications proposed values for maximum reaction load exposure, expressed as either reaction torque, handle displacement, or tightening torque. To conclude, strategies for developing recommendations for reaction load exposure are suggested. Less investigated reaction parameters, e.g. impulse, can carry additional relevant information regarding exposure. Exposure values should be expressed as physical quantities of the reaction load rather than tightening torque. Recommendations are further needed for various tool handle-configurations, emphasizing the increasingly used electric tools. Such recommendations can eventually contribute to reducing MSDs resulting from tightening tool use.
|
|
| 6. |
- Mazaheri, Ava, et al.
(författare)
-
Reaction Parameters Linked to Cumulative Trauma Disorders during Use of Powered Tightening Tools : A Literature Review
- 2019
-
Ingår i: PREMUS 2019. 10th International Scientific Conference on the Prevention of Work-Related Musculoskeletal Disorders.. ; , s. 255-
-
Konferensbidrag (refereegranskat)abstract
- Background: The impact of physical reactions on human operators generated byhandheld powered tightening tools has been researched by evaluating variousparameters, here referred to as ‘reaction parameters’. The objective of this literaturereview is to investigate which reaction parameters commonly are assessed duringphysical load evaluations of tightening tools, as well as reported correlations betweenreaction parameters and risk of developing cumulative trauma disorders (CTDs). Anadditional aim is to map exposure limits established for reaction parameters and identifyknowledge gaps regarding tightening tool impact on operators, if any.Methods: A systematic approach was adopted to review relevant literature, followingthe PRISMA flow-diagram. Synonyms of defined keywords were combined for search in3 databases. 76 articles were read and evaluated against inclusion criteria, of which 47articles where included in a qualitative synthesis. An overview of the assessed reactionparameters was obtained, as well as suggested linkages between these parameters andrisk of injury development.Results: Main parameters studied in literature are reaction force/torque (79%) andhandle displacement (74%). Impulse and handle velocity are studied in 26% and 15% ofthe articles, respectively. 51% of the studies also report a correlation between assessedreaction parameters and risk of developing CTDs. Three studies present exposure limitsfor reaction parameters. 1/3 of the studies were conducted on electric tools, whereasapproximately 2/3 were performed on pneumatic tools.Conclusions: There is a knowledge gap concerning several reaction parametersand their implications for developing CTDs, especially regarding impulse, tool handlevelocity/acceleration and grip force. Their influence is suggested to be explored infurther studies. Establishing exposure limits related to the reaction parameters wouldtranslate the scientific knowledge into industrially applicable recommendations. Further,the need for studies on electric tools is evident, due to a shift in the industry frompneumatic to electric tools.
|
|
| 7. |
|
|
