| 1. |
- Kalscheuer, Thomas, et al.
(författare)
-
Non-linear model error and resolution properties from two-dimensional single and joint inversions of direct current resistivity and radiomagnetotelluric data
- 2010
-
Ingår i: Geophysical Journal International. - 0956-540X .- 1365-246X. ; 182:3, s. 1174-1188
-
Tidskriftsartikel (refereegranskat)abstract
- P>For the first time, a comparative analysis of the resolution and variance properties of 2-D models of electrical resistivity derived from single and joint inversions of dc resistivity (DCR) and radiomagnetotelluric (RMT) measurements is presented. DCR and RMT data are inverted with a smoothness-constrained 2-D scheme. Model resolution, model variance and data resolution analyses are performed both with a classical linearized scheme that employs the smoothness-constrained generalized inverse and a non-linear truncated singular value decomposition (TSVD). In the latter method, the model regularization used in the inversion is avoided and non-linear semi-axes give an approximate description of the non-linear confidence surface in the directions of the model eigenvectors. Hence, this method analyses the constraints that can be provided by the data. Model error estimates are checked against improved and independent estimates of model variability from most-squares inversions. For single and joint inverse models of synthetic data sets, the smoothness-constrained scheme suggests relatively small model errors (typically up to 30 to 40 per cent) and resolving kernels that are spread over several cells in the vicinity of the investigated cell. Linearized smoothness-constrained errors are in good agreement with the corresponding most-squares errors. The variability of the RMT model as estimated from non-linear semi-axes is confirmed by TSVD-based most-squares inversions for most model cells within the depth range of investigation. In contrast to this, most-squares errors of the DCR model are consistently larger than errors estimated from non-linear semi-axes except for the smallest truncation levels. The model analyses confirm previous studies that DCR data can constrain resistive and conductive structures equally well while RMT data provide superior constraints for conductive structures. The joint inversion can improve error and resolution of structures which are within the depth ranges of exploration of both methods. In such parts of the model which are outside the depth range of exploration for one method, error and resolution of the joint inverse model are close to those of the best single inversion result subject to an appropriate weighting of the different data sets.
|
|
| 2. |
|
|
| 3. |
|
|
| 4. |
- Wang, Shunguo, et al.
(författare)
-
Joint inversion of lake-floor electrical resistivity tomography and boat-towed radio-magnetotelluric data illustrated on synthetic data and an application from the Äspö Hard Rock Laboratory site, Sweden
- 2018
-
Ingår i: Geophysical Journal International. - : Oxford University Press (OUP). - 0956-540X .- 1365-246X. ; 213:1, s. 511-533
-
Tidskriftsartikel (refereegranskat)abstract
- The electrical resistivity tomography (ERT) method provides moderately good constraints for both conductive and resistive structures, while the radio-magnetotelluric (RMT) method is well suited to constrain conductive structures. Additionally, RMT and ERT data may have different target coverage and are differently affected by various types of noise. Hence, joint inversion of RMT and ERT data sets may provide a better constrained model as compared to individual inversions. In this study, joint inversion of boat-towed RMT and lake-floor ERT data has for the first time been formulated and implemented. The implementation was tested on both synthetic and field data sets incorporating RMT transverse electrical mode and ERT data. Results from synthetic data demonstrate that the joint inversion yields models with better resolution compared with individual inversions. A case study from an area adjacent to the Ä spö Hard Rock Laboratory (HRL) in southeastern Sweden was used to demonstrate the implementation of the method. A 790-m-long profile comprising lake-floor ERT and boattowed RMT data combined with partial land data was used for this purpose. Joint inversions with and without weighting (applied to different data sets, vertical and horizontal model smoothness) as well as constrained joint inversions incorporating bathymetry data and water resistivity measurementswere performed. The resultingmodels delineate subsurface structures such as a major northeasterly directed fracture system, which is observed in the HRL facility underground and confirmed by boreholes. A previously uncertain weakness zone, likely a fracture system in the northern part of the profile, is inferred in this study. The fractures are highly saturated with saline water, which make them good targets of resistivity-based geophysical methods. Nevertheless, conductive sediments overlain by the lake water add further difficulty to resolve these deep fracture zones. Therefore, the joint inversion of RMT and ERT data particularly helps to improve the resolution of the resistivity models in areas where the profile traverses shallow water and land sections. Our modification of the joint inversion of RMT and ERT data improves the study of geological units underneath shallow water bodies where underground infrastructures are planned. Thus, it allows better planning and mitigating the risks and costs associated with conductive weakness zones.
|
|
