| 1. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Accelerated Mold Test on Dried Pine Sapwood Boards : Impact of Contact Heat Treatment
- 2013
-
Ingår i: Journal of wood chemistry and technology. - : Taylor & Francis. - 0277-3813 .- 1532-2319. ; 33:3, s. 174-187
-
Tidskriftsartikel (refereegranskat)abstract
- We test the hypothesis that the combination of kiln drying of double-stacked boards and contact heat treatment will reduce the susceptibility of treated boards to colonization by mold fungi. Winter-felled Scots pine (Pinus sylvestris L.) sapwood boards were double-stacked in an industrial kiln in ''sapwood out'' and ''sapwood in'' positions. Dried samples were then contact heat-treated using a hot press at three different temperatures (140°C, 170°C, and 200°C) for three different periods (1, 3, and 10 min). An accelerated mold test was performed in a climate chamber where naturally mold-infected samples were used as a source of mold inocula. Contact heat treatment degraded the saccharides that accumulated at dried surfaces, and reduced the mold growth. The threshold temperature and time for inhibiting mold growth were 170°C for 10 min. However, for industrial application, the most feasible combination of temperature and time would be 200°C for 3 min. We concluded that double stacking/contact heat treatment used is an environmentally friendly alternative to chemicals for reducing mold on Scots pine sapwood boards.
|
|
| 2. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Anatomical properties and process parameters affecting blister/blow formation in densified European aspen and downy birch sapwood boards by thermo-hygro-mechanical compression
- 2013
-
Ingår i: Journal of Materials Science. - : Springer Science and Business Media LLC. - 0022-2461 .- 1573-4803. ; 48:24, s. 8571-8579
-
Tidskriftsartikel (refereegranskat)abstract
- Approximately, 13.5 % of the standing volume of productive forest land in Sweden is covered by birch and aspen, which provides the vast potential to produce value-added products such as densified wood. This study shows whether it is possible to densify those species with a thermo-hygro-mechanical (THM) process using heat, steam, and pressure. In this process, transverse compression on thin European aspen (Populus tremula) and downy birch (Betula pubescens) boards was performed at 200 ºC with a maximum steam pressure of 550 kPa. To obtain a theoretical 50 % compression set, the press’s maximum hydraulic pressure ranged from 1.5 to 7.3 MPa. Preliminary tests showed that ~75 % of the birch boards produced defects (blisters/blows) while only 25 % of the aspen boards did. Mainly, radial delamination associated with internal checks in intrawall and transwall fractures caused small cracks (termed blisters) while blows are characterized by relatively larger areas of delamination visible as a bumpy surface on the panel. Anatomical investigations revealed that birch was more prone to those defects than aspen. However, those defects could be minimized by increasing the pre-treatment time during the THM processing.
|
|
| 3. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Development of a new rapid method for mould testing in a climate chamber : preliminary tests
- 2013
-
Ingår i: European Journal of Wood and Wood Products. - : Springer. - 0018-3768 .- 1436-736X. ; 71:4, s. 451-461
-
Tidskriftsartikel (refereegranskat)abstract
- The purpose of this study was to develop fast, simple and robust solid wood mould testing methods for the use in small-scale laboratory tests. The objective was to investigate mould susceptibility of different wood materials within the batches. The proposed method is based on natural contamination of non-sterile surfaces in climates conducive to mould growth. For this purpose, a climate chamber with regulated temperature and relative humidity was used. The conditioning chamber was divided into upper and lower chamber by a thin layer of stainless steel placed horizontally above the fan to minimise air circulation to the sample in the upper compartment. Mould-infected samples from outdoor tests were used as a source of mould inocula, and test trials were conducted on Scots pine (Pinus sylvestris L.) sapwood. Samples were suspended from the top of the upper chamber, and the chamber was exposed to different temperature and humidity levels. Severe mould infestation was observed after 12–14 days of incubation. Visual mould rating was then performed. Regardless of some constraints, this test method was very simple, fast, and effective. More importantly, unlike other test methods, it closely models mould infestation as it would occur under natural condition.
|
|
| 4. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Distribution of preservatives in thermally modified Scots pine and Norway spruce sapwood
- 2013
-
Ingår i: Wood Science and Technology. - : Springer Science and Business Media LLC. - 0043-7719 .- 1432-5225. ; 47:3, s. 499-513
-
Tidskriftsartikel (refereegranskat)abstract
- Studying the impregnation and distribution of oil-based preservative in dried wood is complicated as wood is a nonhomogeneous, hygroscopic and porous material, and especially of anisotropic nature. However, this study is important since it has influence on the durability of wood. To enhance the durability of thermally modified wood, a new method for preservative impregnation is introduced, avoiding the need for external pressure or vacuum. This article presents a study on preservative distribution in thermally treated Scots pine (Pinus sylvestris L.) and Norway spruce (Picea abies (L.) Karst.) sapwood using computed tomography scanning, light microscopy, and scanning electron microscopy. Secondary treatment of thermally modified wood was performed on a laboratory scale by impregnation with two types of preservatives, viz. Elit Träskydd (Beckers) and pine tar (tar), to evaluate their distribution in the wood cells. Preservative solutions were impregnated in the wood using a simple and effective method. Samples were preheated to 170°C in a drying oven and immediately submerged in preservative solutions for simultaneous impregnation and cooling. Tar penetration was found higher than Beckers, and their distribution decreased with increasing sample length. Owing to some anatomical properties, uptake of preservatives was low in spruce. Besides, dry-induced interstitial spaces, which are proven important flow paths for seasoned wood, were not observed in this species.
|
|
| 5. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Effect of oil impregnation on water repellency, dimensional stability and mold susceptibility of thermally-modified European aspen and downy birch wood
- 2017
-
Ingår i: Journal of Wood Science. - Japan : Springer. - 1435-0211 .- 1611-4663. ; 63:1, s. 74-82
-
Tidskriftsartikel (refereegranskat)abstract
- Conventional chemical wood preservatives have been banned or restricted in some applications due to human and animal toxicity and their adverse impact on the surrounding environment. New, low-environmental-impact wood treatments that still provide effective protection systems are needed to protect wood. Thermal modification of wood could reduce hygroscopicity, improve dimensional stability and enhance resistance to mold attack. The aim of this study is to investigate if these properties enhanced in thermally-modified (TM) wood through treatments with oils. In this study, TM European aspen (Populus tremula) and downy birch (Betula pubescens) wood were impregnated with three different types of oil: water-miscible commercial Elit Träskydd (Beckers oil with propiconazole and 3-iodo-2-propynyl butylcarbamate, IPBC), a pine tar formulation and 100% tung oil. The properties of oil-impregnated wood investigated were water repellency, dimensional stability and mold susceptibility. The treated wood especially with pine tar and tung oil, showed an increase in water repellency and dimensional stability. However, Beckers oil which contains biocides like propiconazole and IPBC, showed better protection against mold compared with pine tar and tung oil. To enhance the dimensional stability of the wood, pine tar and tung oil can be used, but these oil treatments did not significantly improve mold resistance rather sometimes enhanced the mold growth. Whereas, a significant anti-mold effect was observed on Beckers oil treated samples.
|
|
| 6. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Evaluation of preservative distribution in thermally modified European aspen and birch boards using computed tomography and scanning electron microscopy
- 2013
-
Ingår i: Journal of Wood Science. - : Springer. - 1435-0211 .- 1611-4663. ; 59:1, s. 57-66
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of this experiment was to impregnate thermally modified wood using an easy and cost-effective method. Industrially processed thermally modified European aspen (Populus tremula L.) and birch (Betula pubescens Ehrh.) were collected and secondarily treated at the laboratory scale with the preservatives tung oil, pine tar and Elit Träskydd (Beckers) using a simple and effective method. Preservative uptake and distribution in sample boards were evaluated using computed tomography (CT) and scanning electron microscopy (SEM) techniques. Preservative uptake and treatability in terms of void volume filled were found the highest in Beckers and the lowest in tung oil-treated samples. Thermally modified samples had lower treatability than their counterpart control samples. More structural changes after thermal modification, especially in birch, significantly reduced the preservative uptake and distribution. The differences of preservatives uptake near the end grain were high and then decreased near the mid position of the samples length as compared with similar type of wood sample. Non-destructive evaluation by CT scanning provided a very useful method to locate the preservative gradients throughout the sample length. SEM analysis enabled the visualization of the preservative deposits in wood cells at the microstructural level.
|
|
| 7. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Förstudie: värmebehandling av trä : slutrapport
- 2012
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- Projektet har bedrivits som en förstudie till en större ansökan inom området Värmebehandlat trä för interiört bruk. Projektet inleds med studier av olje- och tjärupptagning i värmebehandlat trä genomen speciell impregneringsmetod som bygger på förvärmning och undertryck i materialet. Tanken är att med denna metod kunna tillföre ytterligare en egenskap som skyddar trä och gör det attraktivt för inomhusbruk genom att t ex blockera den något besvärande luft som kommer från värmebehandlat trä.Projektet syftar till att undersöka möjligheten att med en förenklad impregneringsmetod erhålla tillräcklig penetrering av impregneringsmedel (Becker olja och trätjära) och i samband därmed studera fördelningen av impregneringsmedel i trä.
|
|
| 8. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Moisture properties of heat-treated Scots pine and Norway spruce sapwood impregnated with wood preservatives
- 2012
-
Ingår i: Wood and Fiber Science. - : Society of Wood Science and Technology. - 0735-6161. ; 44:1, s. 85-93
-
Tidskriftsartikel (refereegranskat)abstract
- An experiment was conducted on commercially heat-treated (HT) Scots pine (Pinus sylvestris L.) and Norway spruce (Picea abies [L.] Karst.) sapwood collected from Ht Wood AB, Arvidsjaur, Sweden. Secondary treatment on HT wood was performed in laboratory scale by impregnating with water-repellent preservatives (a commercial one and pine tar) to evaluate their retention and different moisture-related properties. Preservative solutions were impregnated using a simple and effective method. Wood samples were heated at 170°C in a dry oven and were immediately immersed in preservative solutions. Considerable retention was observed in HT wood, particularly in pine. Moisture adsorption properties were measured after conditioning in a high-humidity environmental chamber (4°C and 84% RH). Experimental results showed that secondary treatment enhanced moisture excluding efficiencies by decreasing equilibrium moisture content, suggesting better hydrophobicity. Soaking test in water showed that antiswelling and water repellence efficiencies improved, especially in tar-treated wood. In addition, this type of treatment significantly decreased water absorption. It was also possible to decrease volumetric swellings. Thus, secondary treatment of HT wood with preservative, in particular with tar, improved dimensional stability and water repellency.
|
|
| 9. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Mould susceptibility of Scots pine (Pinus sylvestris L.) sapwood : Impact of drying, thermal modification, and copper-based preservative
- 2013
-
Ingår i: International Biodeterioration & Biodegradation. - : Elsevier. - 0964-8305 .- 1879-0208. ; 85, s. 284-288
-
Tidskriftsartikel (refereegranskat)abstract
- The development of mould on wood surfaces depends on several factors. Although mould does not affect the mechanical properties of wood, it greatly reduces the aesthetic value of wood such as the sapwood of Scots pine (Pinus sylvestris L.), which is very prone to mould. In addition, adverse health effects of mould on humans are a great concern. Different types of dried and treated wood were used to observe whether they had enhanced durability against mould following an accelerated laboratory test method in a climate chamber. Samples were green, air-dried, industrially thermally modified, treated with copper-based preservative, and kiln-dried wood, which were tested within a single test run. The test produced the following main results: The thermal modification increased the durability of the wood, and the protective effectiveness of alternative treatments was comparable to that of commercially available copper-based treatment. However, the initial moisture content of the samples during mould exposure had a great influence on the onset of mould growth. The risk of mould susceptibility of industrial kiln-dried lumber can be reduced by drying using the double-layering technique and planing off the nutrient enriched evaporation surfaces.
|
|
| 10. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Uneven distribution of preservative in kiln-dried sapwood lumber of Scots pine : Impact of wood structure and resin allocation
- 2012
-
Ingår i: Holzforschung. - : Walter de Gruyter. - 0018-3830 .- 1437-434X. ; 66:2, s. 251-258
-
Tidskriftsartikel (refereegranskat)abstract
- Scots pine (Pinus sylvestris L.) sapwood lumber was collected after kiln drying and preservative treatment with Celcure AC 800 (a copper-amine wood preservative). Distribution of the preservative throughout the lumber was visually examined. Not all, but some samples showed specific localized areas without any preservative distribution throughout their entire length. Those samples were assessed further for anatomical properties, specifically in impregnated and unimpregnated areas. Additional study was conducted on the morphological nature and redistribution of lipophilic extractives using three different histochemical staining methods. Intrinsic wood properties – especially the frequency of axial resin canals and the percentage of canals blocked – were found to be responsible for the irregular distribution of the preservative. Furthermore, the inability to create continuous and frequent interstitial spaces due to the collapse of thin-walled ray cells throughout the lumber resulted in un-even distribution of preservatives. Staining techniques were useful to localize places with more or less abundance of extractives (e.g., fats) in impregnated and unimpregnated wood, which varied considerably. Histochemical observations revealed information pertaining to the kiln dry specific distribution and redistribution of extractives between the areas. Moreover, resin reallocation and modification in ray parenchyma and resin canals induced by kiln drying would be another reason for the impregnation anomalies.
|
|
