| 1. |
|
|
| 2. |
- Asarnoj, A., et al.
(författare)
-
IgE to peanut allergen components : relation to peanut symptoms and pollen sensitization in 8-year-olds
- 2010
-
Ingår i: Allergy. European Journal of Allergy and Clinical Immunology. - : Wiley. - 0105-4538 .- 1398-9995. ; 65:9, s. 1189-1195
-
Tidskriftsartikel (refereegranskat)abstract
- Background: Allergen-specific IgE testing is often performed with crude peanut extract, but the results may be difficult to interpret because of cross-reactions between peanut and other plant allergens. The aim was to investigate IgE reactivity to peanut allergen components in children from a birch-rich region in relation to pollen sensitization and peanut symptoms. Methods: From a birth cohort, clinical parameters were obtained through questionnaires and IgE antibody levels to peanut and birch pollen were measured. Different peanut/birch sensitization phenotypes were defined among 200 selected children. IgE reactivity to peanut and pollen allergen components was analysed using microarray technique. Results: Peanut symptoms were reported in 87% of the children with IgE reactivity to any of the peanut allergens Ara h 1, 2 or 3 but not to Ara h 8 (n = 46) vs 17% of children with IgE reactivity to Ara h 8 but not to Ara h 1, 2 or 3 (n = 23), P < 0.001. Furthermore, symptoms were more severe in children with Ara h 1, 2 or 3 reactivity. Children with IgE reactivity both to Ara h 2 and to Ara h 1 or 3 more often reported peanut symptoms than children with IgE only to Ara h 2 (97% vs 70%, P = 0.016), particularly respiratory symptoms (50% vs 9%, P = 0.002). Conclusions: IgE analysis to peanut allergen components may be used to distinguish between peanut-sensitized individuals at risk of severe symptoms and those likely to have milder or no symptoms to peanut if sensitized to pollen allergens and their peanut homologue allergens.
|
|
| 3. |
- Azeez, Ahmed, 1991-, et al.
(författare)
-
Out-of-phase thermomechanical fatigue crack propagation in a steam turbine steel — modelling of crack closure
- 2021
-
Ingår i: International Journal of Fatigue. - : Elsevier. - 0142-1123 .- 1879-3452. ; 149
-
Tidskriftsartikel (refereegranskat)abstract
- Understanding of crack growth behaviour is necessary to predict accurate fatigue lives. Out-of-phase thermomechanical fatigue crack propagation tests were performed on FB2 steel used in high-temperature steam turbine sections. Testing results showed crack closure where the compressive part of the fatigue cycle affected crack growth rate. Crack closing stress was observed to be different, and had more influence on the growth rate, than crack opening stress. Crack growth rate was largely controlled by the minimum temperature of the cycle, which agreed with an isothermal crack propagation test. Finite element models with stationary sharp cracks captured the crack closure behaviour.
|
|
| 4. |
- Azeez, Ahmed, 1991-, et al.
(författare)
-
The effect of dwell times and minimum temperature on out-of-phase thermomechanical fatigue crack propagation in a steam turbine steel - Crack closure prediction
- 2022
-
Ingår i: International Journal of Fatigue. - : Elsevier Science Ltd. - 0142-1123 .- 1879-3452. ; 162
-
Tidskriftsartikel (refereegranskat)abstract
- Exploring crack growth behaviour is needed to establish accurate fatigue life predictions. Cracked specimens were tested under strain-controlled out-of-phase thermomechanical fatigue conditions. The tests included dwell times and three different minimum temperatures. Higher minimum temperature gave faster crack growth rates while the additions of dwell times showed no effects. Crack closure was observed in all the tests where the addition of dwell times and change in minimum temperature displayed little to no effect on crack closure stresses. Finite element models with a sharp stationary crack and material parameters switching provided acceptable predictions for the maximum, minimum, and crack closure stresses.
|
|
| 5. |
- Balachandramurthi, Arun Ramanathan, 1989-, et al.
(författare)
-
Anisotropic fatigue properties of Alloy 718 manufactured by Electron Beam Powder Bed Fusion
- 2020
-
Ingår i: International Journal of Fatigue. - : Elsevier. - 0142-1123 .- 1879-3452. ; 141
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, Alloy 718 specimens manufactured by Electron Beam Powder Bed Fusion process are subjected to two different post-treatments to have different microstructural features. Low cycle fatigue testing has been performed both parallel and transverse to the build direction. EB-PBF Alloy 718 exhibits anisotropic fatigue behaviour; the fatigue life is better along the parallel direction compared to the transverse direction. The anisotropy in fatigue life is related to the anisotropy in the Young’s modulus. The pseudo-elastic stress vs. fatigue life approach is presented as a potential solution to handle anisotropy in fatigue life assessment of additively manufactured engineering components. © 2020 The Authors
|
|
| 6. |
- Balachandramurthi, Arun Ramanathan
(författare)
-
Fatigue Properties of Additively Manufactured Alloy 718
- 2018
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Additive Manufacturing (AM), commonly known as 3D Printing, is a disruptive modern manufacturing process, in which parts are manufactured in a layer-wise fashion. Among the metal AM processes, Powder Bed Fusion (PBF) technology has opened up a design space that was not formerly accessible with conventional manufacturing processes. It is, now, possible to manufacture complex geometries, such as topology-optimized structures, lattice structures and intricate internal channels, with relative ease. PBF is comprised of Electron Beam Melting (EBM) and Selective Laser Melting (SLM) processes.Though AM processes offer several advantages, the suitability of these processes to replace conventional manufacturing processes must be studied in detail; for instance, the capability to produce components of consistent quality. Therefore, understanding the relationship between the AM process together with the post treatment used and the resulting microstructure and its influence on the mechanical properties is crucial, to enable manufacturing of high-performance components. In this regard, for AM built Alloy 718, only a limited amount of work has been performed compared to conventional processes such as casting and forging. The aim of this work, therefore, is to understand how the fatigue properties of EBM and SLM built Alloy 718, subjected to different thermal post-treatments, is affected by the microstructure. In addition, the effect of as-built surface roughness is also studied.Defects can have a detrimental effect on fatigue life. Numerous factors such as the defect type, size, shape, location, distribution and nature determine the effect of defects on properties. Hot Isostatic Pressing (HIP) improves fatigue life as it leads to closure of most defects. Presence of oxides in the defects, however, hinders complete closure by HIP. Machining the as-built surface improves fatiguelife; however, for EBM manufactured material, the extent of improvement is dependent on the amount of material removed. The as-built surface roughness, which has numerous crack initiation sites, leads to lower scatter in fatigue life. In both SLM and EBM manufactured material, fatigue crack propagation is transgranular. Crack propagation is affected by grain size and texture of the material.
|
|
| 7. |
- Balachandramurthi, Arun Ramanathan, et al.
(författare)
-
Influence of defects and as-built surface roughness on fatigue properties of additively manufactured Alloy 718
- 2018
-
Ingår i: Materials Science & Engineering. - : Elsevier BV. - 0921-5093 .- 1873-4936. ; 735, s. 463-474
-
Tidskriftsartikel (refereegranskat)abstract
- Electron beam melting (EBM) and Selective Laser Melting (SLM) are powder bed based additive manufacturing (AM) processes. These, relatively new, processes offer advantages such as near net shaping, manufacturing complex geometries with a design space that was previously not accessible with conventional manufacturing processes, part consolidation to reduce number of assemblies, shorter time to market etc. The aerospace and gas turbine industries have shown interest in the EBM and the SLM processes to enable topology-optimized designs, parts with lattice structures and part consolidation. However, to realize such advantages, factors affecting the mechanical properties must be well understood – especially the fatigue properties. In the context of fatigue performance, apart from the effect of different phases in the material, the effect of defects in terms of both the amount and distribution and the effect of “rough†as-built surface must be studied in detail. Fatigue properties of Alloy 718, a Ni-Fe based superalloy widely used in the aerospace engines is investigated in this study. Four point bending fatigue tests have been performed at 20 Hz in room temperature at different stress ranges to compare the performance of the EBM and the SLM material to the wrought material. The experiment aims to assess the differences in fatigue properties between the two powder bed AM processes as well as assess the effect of two post-treatment methods namely – machining and hot isostatic pressing (HIP). Fractography and metallography have been performed to explain the observed properties. Both HIPing and machining improve the fatigue performance; however, a large scatter is observed for machined specimens. Fatigue properties of SLM material approach that of wrought material while in EBM material defects severely affect the fatigue life. © 2018 Elsevier B.V.
|
|
| 8. |
- Balachandramurthi, Arun Ramanathan, 1989-, et al.
(författare)
-
Microstructural influence on fatigue crack propagation during high cycle fatigue testing of additively manufactured Alloy 718
- 2019
-
Ingår i: Materials Characterization. - : Elsevier BV. - 1044-5803 .- 1873-4189. ; 149, s. 82-94
-
Tidskriftsartikel (refereegranskat)abstract
- A study of the microstructure of additively manufactured Alloy 718 was performed in order to better understand the parameters that have an influence on the fatigue properties of the material. The specimens were manufactured using two powder bed fusion techniques – Electron Beam Melting (EBM) and Selective Laser Melting (SLM). Four point bending fatigue tests were performed at room temperature with a stress ratio of R = 0.1 and 20 Hz frequency, on material that was either in hot isostatically pressed (HIP) and solution treated and aged (STA) condition or in STA condition without a prior HIP treatment. The grains in the SLM material in the HIP + STA condition have grown considerably both in the hatch and the contour regions; EBM material, in contrast, shows grain growth only in the contour region. Fractographic analysis of the specimens in HIP + STA condition showed a faceted appearance while the specimens in STA condition showed a more planar crack appearance. The crack propagation occurred in a transgranular mode and it was found that precipitatessuch as NbC, TiN or δ-phase, when present, did not affect the crack path. The areas with larger grains corresponded to the faceted appearance of the fracture surface. This could be attributed to the plastic zone ahead of the crack tip being confined within one grain, in case of the larger grains, which promotes single shear crack growth mode
|
|
| 9. |
- Balachandramurthi, Arun Ramanathan, 1989-, et al.
(författare)
-
Microstructure tailoring in Electron Beam Powder Bed Fusion Additive Manufacturing and its potential consequences
- 2019
-
Ingår i: Results in Materials. - : Elsevier. - 2590-048X. ; 1
-
Tidskriftsartikel (refereegranskat)abstract
- Electron Beam Powder Bed Fusion process for Alloy 718 was investigated, in the sense of microstructural evolution with varying process conditions. The existence of a geometric relationship between the melt front and the processing parameters was observed. By understanding and capitalizing on this relationship, it was possible to obtain columnar, equiaxed or bimodal microstructure.
|
|
| 10. |
- Balachandramurthi, Arun Ramanathan, 1989-, et al.
(författare)
-
On the microstructure of laser beam powder bed fusion alloy 718 and its influence on the low cycle fatigue behaviour
- 2020
-
Ingår i: Materials. - : MDPI AG. - 1996-1944. ; 13:22
-
Tidskriftsartikel (refereegranskat)abstract
- Additive manufacturing of Alloy 718 has become a popular subject of research in recent years. Understanding the process-microstructure-property relationship of additively manufactured Alloy 718 is crucial for maturing the technology to manufacture critical components. Fatigue behaviour is a key mechanical property that is required in applications such as gas turbines. Therefore, in the present work, low cycle fatigue behaviour of Alloy 718 manufactured by laser beam powder bed fusion process has been investigated. The material was tested in as-built condition as well as after two different thermal post-treatments. Three orientations with respect to the building direction were tested to evaluate the anisotropy. Testing was performed at room temperature under controlled amplitudes of strain. It was found that defects, inclusions, strengthening precipitates, and Young’s modulus influence the fatigue behaviour under strain-controlled conditions. The strengthening precipitates affected the deformation mechanism as well as the cycle-dependent hardening/softening behaviour. The defects and the inclusions had a detrimental effect on fatigue life. The presence of Laves phase in LB-PBF Alloy 718 did not have a detrimental effect on fatigue life. Young’s modulus was anisotropic and it contributed to the anisotropy in strain-life relationship. Pseudo-elastic stress vs. fatigue life approach could be used to handle the modulus-induced anisotropy in the strain-life relationship. © 2020 by the authors. Licensee MDPI, Basel, Switzerland.
|
|
