| 1. |
- Abdel Aziz, Ilaria, et al.
(författare)
-
Electrochemical modulation of mechanical properties of glycolated polythiophenes
- 2024
-
Ingår i: Materials Horizons. - : ROYAL SOC CHEMISTRY. - 2051-6347 .- 2051-6355.
-
Tidskriftsartikel (refereegranskat)abstract
- Electrochemical doping of organic mixed ionic-electronic conductors is key for modulating their conductivity, charge storage and volume enabling high performing bioelectronic devices such as recording and stimulating electrodes, transistors-based sensors and actuators. However, electrochemical doping has not been explored to the same extent for modulating the mechanical properties of OMIECs on demand. Here, we report a qualitative and quantitative study on how the mechanical properties of a glycolated polythiophene, p(g3T2), change in situ during electrochemical doping and de-doping. The Young's modulus of p(g3T2) changes from 69 MPa in the dry state to less than 10 MPa in the hydrated state and then further decreases down to 0.4 MPa when electrochemically doped. With electrochemical doping-dedoping the Young's modulus of p(g3T2) changes by more than one order of magnitude reversibly, representing the largest modulation reported for an OMIEC. Furthermore, we show that the electrolyte concentration affects the magnitude of the change, demonstrating that in less concentrated electrolytes more water is driven into the film due to osmosis and therefore the film becomes softer. Finally, we find that the oligo ethylene glycol side chain functionality, specifically the length and asymmetry, affects the extent of modulation. Our findings show that glycolated polythiophenes are promising materials for mechanical actuators with a tunable modulus similar to the range of biological tissues, thus opening a pathway for new mechanostimulation devices. This work investigates the changes in the mechanical properties of glycolated polythiophenes induced by electrochemical addressing and by electrolyte concentration, due to its ability to stabilize water.
|
|
| 2. |
|
|
| 3. |
- Bergqvist, Jonas, et al.
(författare)
-
Time-resolved morphology formation of solution cast polymer : fullerene blends revealed by in-situ photoluminescence spectroscopy
- 2015
-
Annan publikation (övrigt vetenskapligt/konstnärligt)abstract
- The nanoscale morphology of the photo-active layer in organic solar cells is critical for device efficiency. The photoactive layer is cast from solution and during drying both the polymer and the fullerene self-assemble to form a blend. Here, we introduce in-situ spectroscopic photoluminescence (PL) combined with laser reflectometry to monitor the drying process of an amorphous polymer:fullerene blend. When casting only the pristine components (polymer or PCBM only), the strength of PL emission is proportional to the solid content of the drying solution, and both kinetics reveal a rapid aggregation onset at the final stage of film drying. On the contrary, when casting polymer:fullerene blends, the strength of PL emission is proportional to the wet film thickness and reveals polymer/fullerene charge transfer (CT) already at the earliest stages of film drying, i.e. in dilute solutions. The proposed method allows to detect polymer/fullerene phase separation during film casting – from a reduction in the PL quenching rate as the film dries. Poor solvents lead to phase separation already at early stages of film drying (low solid content), resulting in a coarse final morphology as confirmed by atomic force microscopy (AFM). We therefore anticipate that the proposed method will be an important tool in the future development of processing inks, not only for solution-cast polymer:fullerene solar cells but also for organic heterojunctions in general.
|
|
| 4. |
|
|
| 5. |
- Bäcklund, Fredrik, et al.
(författare)
-
Conducting microhelices from self-assembly of protein fibrils
- 2017
-
Ingår i: Soft Matter. - : Royal Society of Chemistry. - 1744-683X .- 1744-6848. ; 13:25, s. 4412-4417
-
Tidskriftsartikel (refereegranskat)abstract
- Herein we utilize insulin to prepare amyloid based chiral heliceswith either right or left handed helicity. We demonstrate that thehelices can be utilized as structural templates for the conductingpolymer alkoxysulfonate poly(ethylenedioxythiophene) (PEDOT-S).The chirality of the helical assembly is transferred to PEDOT-S asdemonstrated by polarized optical microscopy (POM) and CircularDichroism (CD). Analysis of the helices by conductive atomic force(c-AFM) shows significant conductivity. In addition the morphologyof the template structure is stabilized by PEDOT-S. Theseconductive helical structures represent promising candidates in ourquest for THz resonators.
|
|
| 6. |
- Cai, Wanzhu, et al.
(författare)
-
Self-doped conjugated polyelectrolyte with tuneable work function for effective hole transport in polymer solar cells
- 2016
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry. - 2050-7488 .- 2050-7496. ; 4:40, s. 15670-15675
-
Tidskriftsartikel (refereegranskat)abstract
- A water-soluble conjugated polyelectrolyte (CPE), PEDOT-S (poly(4-(2,3-dihydrothieno[3,4-b][1,4]dioxin-2-yl-methoxy)-1-butanesulfonic acid)), is demonstrated to be an excellent hole transport material in several polymer solar cells with different donor's HOMO (highest occupied molecular orbital). With a P3TI:PC71BM (poly[6,6′-bis(5′-bromo-3,4′-dioctyl-[2,2′-bithiophen]-5-yl)-1,1′-bis(2-hexyldecyl)-[3,3′-biindolinylidene]-2,2′-dione]:[6,6]-phenyl C71 butyric acid methyl ester) active layer, the device using PEDOT-S as a hole transport layer (HTL) outperforms the PEDOT:PSS-based devices due to an increased FF (fill factor). The devices' current density–voltage characteristics (J–V) show that a PEDOT-S layer can operate well with a wide range of thicknesses as well, helped by its high conductivity and decent transparency. With UV-ozone treatment, the work function of the PEDOT-S can increase from 4.9 eV to 5.2 eV. In TQ1:PC71BM (poly[[2,3-bis(3-octyloxyphenyl)-5,8-quinoxalinediyl]-2,5-thiophenediyl]:PC71BM) devices, which have a deeper donor HOMO than P3TI, Voc is improved from 0.81 V to 0.92 V by 7 min UV-ozone treatment, along with a suppressed reverse injection current and increased Jsc (short-circuit current density) and FF. Topography study shows the excellent coating ability of PEDOT-S. Conductive atomic force microscopy (C-AFM) shows the out-of-plane current in PEDOT-S film is one thousand times higher than that in PEDOT:PSS PH 4083 film under the same electric field and has much more uniformly distributed current pathways.
|
|
| 7. |
- Edberg, Jesper, et al.
(författare)
-
Patterning and Conductivity Modulation of Conductive Polymers by UV Light Exposure
- 2016
-
Ingår i: Advanced Functional Materials. - : WILEY-V C H VERLAG GMBH. - 1616-301X .- 1616-3028. ; 26:38, s. 6950-6960
-
Tidskriftsartikel (refereegranskat)abstract
- A novel patterning technique of conductive polymers produced by vapor phase polymerization is demonstrated. The method involves exposing an oxidant film to UV light which changes the local chemical environment of the oxidant and subsequently the polymerization kinetics. This procedure is used to control the conductivity in the conjugated polymer poly(3,4-ethylenedioxythiophene): tosylate by more than six orders of magnitude in addition to producing high-resolution patterns and optical gradients. The mechanism behind the modulation in the polymerization kinetics by UV light irradiation as well as the properties of the resulting polymer are investigated.
|
|
| 8. |
- Elfwing, Anders, et al.
(författare)
-
Protein nanowires with conductive properties
- 2015
-
Ingår i: Journal of Materials Chemistry C. - : Royal Society of Chemistry. - 2050-7526 .- 2050-7534. ; 3:25, s. 6499-6504
-
Tidskriftsartikel (refereegranskat)abstract
- Herein we report on the investigation of self-assembled protein nanofibrils functionalized with metallic organic compounds. We have characterized the electronic behaviour of individual nanowires using conductive atomic force microscopy. In order to follow the self assembly process we have incorporated fluorescent molecules into the protein and used the energy transfer between the internalized dye and the metallic coating to probe the binding of the polyelectrolyte to the fibril.
|
|
| 9. |
- Johansson, Patrik, et al.
(författare)
-
Electronic polymers in lipid membranes
- 2015
-
Ingår i: Scientific Reports. - : Nature Publishing Group. - 2045-2322. ; 5:11242
-
Tidskriftsartikel (refereegranskat)abstract
- Electrical interfaces between biological cells and man-made electrical devices exist in many forms, but it remains a challenge to bridge the different mechanical and chemical environments of electronic conductors (metals, semiconductors) and biosystems. Here we demonstrate soft electrical interfaces, by integrating the metallic polymer PEDOT-S into lipid membranes. By preparing complexes between alkyl-ammonium salts and PEDOT-S we were able to integrate PEDOT-S into both liposomes and in lipid bilayers on solid surfaces. This is a step towards efficient electronic conduction within lipid membranes. We also demonstrate that the PEDOT-S@alkyl-ammonium: lipid hybrid structures created in this work affect ion channels in the membrane of Xenopus oocytes, which shows the possibility to access and control cell membrane structures with conductive polyelectrolytes.
|
|
| 10. |
- Kroon, Renee, 1982, et al.
(författare)
-
Comparison of selenophene and thienothiophene incorporation into pentacyclic lactam-based conjugated polymers for organic solar cells
- 2015
-
Ingår i: Polymer Chemistry. - : Royal Society of Chemistry (RSC). - 1759-9954 .- 1759-9962. ; 6:42, s. 7402-7409
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, we compare the effect of incorporating selenophene versus thienothiophene spacers into pentacyclic lactam-based conjugated polymers for organic solar cells. The two cyclic lactam-based copolymers were obtained via a new synthetic method for the lactam moiety. Selenophene incorporation results in a broader and red-shifted optical absorption while retaining a deep highest occupied molecular orbital level, whereas thienothienophene incorporation results in a blue-shifted optical absorption. Additionally, grazing-incidence wide angle X-ray scattering data indicates edge- and face-on solid state order for the selenophene-based polymer as compared to the thienothiophene-based polymer, which orders predominantly edge-on with respect to the substrate. In polymer : PC71BM bulk heterojunction solar cells both materials show a similar open-circuit voltage of similar to 0.80-0.84 V, however the selenophene-based polymer displays a higher fill factor of similar to 0.70 vs. similar to 0.65. This is due to the partial face-on backbone orientation of the selenophene-based polymer, leading to a higher hole mobility, as confirmed by single-carrier diode measurements, and a concomitantly higher fill factor. Combined with improved spectral coverage of the selenophene-based polymer, as confirmed by quantum efficiency experiments, it offers a larger short-circuit current density of similar to 12 mA cm(-2). Despite the relatively low molecular weight of both materials, a very robust power conversion efficiency similar to 7% is achieved for the selenophene-based polymer, while the thienothiophene-based polymer demonstrates only a moderate maximum PCE of similar to 5.5%. Hence, the favorable effects of selenophene incorporation on the photovoltaic performance of pentacyclic lactam-based conjugated polymers are clearly demonstrated.
|
|
