| 1. |
- Abolhasani, Hasanali, et al.
(författare)
-
Development of self-healable acrylic water-based environmental-friendly coating as an alternative to chromates coatings
- 2023
-
Ingår i: Progress in organic coatings. - : Elsevier B.V.. - 0300-9440 .- 1873-331X. ; 176
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, different coating systems, including solvent-based epoxy and water-based acrylic resins, were evaluated for their potential as an alternative to chromate coatings in order to avoid Cr(VI) toxic hazards. The resins were used as either pigment-free coatings or were formulated with 20-wt% zinc/aluminum pigments. The coatings were subsequently applied on galvanized ST12 steel plates and their corrosion resistance was investigated by electrochemical impedance spectroscopy (EIS) evaluations. The effect of the binder and pigment type on the impact resistance of two different polymeric coatings was also evaluated. The results of impact tests revealed completely peeled film from the substrate for epoxy coatings. However, under the same experimental conditions, very few small cracks were created in water-based acrylic coatings for both pigmented and pigment-free cases. In addition, some other parameters such as drying time and coating cost were taken into account to select a good alternative to chromate coatings. The results of this work can facilitate the introduction of an inexpensive environmentally friendly acrylic coating as a promising self-healing alternative to chromate coating.
|
|
| 2. |
- Aminoroaya, Alireza, et al.
(författare)
-
A Review of Dental Composites : Methods Of Characterizations
- 2020
-
Ingår i: ACS Biomaterials Science & Engineering. - : American Chemical Society (ACS). - 2373-9878. ; 6:7, s. 3713-3744
-
Forskningsöversikt (refereegranskat)abstract
- Dental composites are becoming increasingly popular in esthetic restorative dentistry and present a promising substitute for amalgam. However, the major hurdles that hinder their total adoption in restorative dentistry are limited longevity and possible health risks, leading to significant attempts for addressing these shortcomings. Besides the new materials, the evaluation methods play a critical role in the introduction and improvement of these types of materials. This review aims to cover the characterization methods in the evaluation of dental composites that are most employed nowadays. Therefore, the methods for evaluating the physical properties of the dental composites are first explained. Subsequently, the assessment methods of curing kinetics and the mechanical properties of the composites are classified and reviewed. Afterward, the article delves into the introduction and classification of the microscopic and antibacterial evaluation methods. Finally, the test methods for assessment of in vitro cytotoxicity and self-healing ability are described. It should be noted, for each test method, the most recent and interesting articles are cited. It is envisaged that this review will facilitate an understanding and provide knowledge for the section and utilizing the most effective and suitable characterization methods for future research on the development of dental composites.
|
|
| 3. |
- Aminoroaya, Alireza, et al.
(författare)
-
A review of dental composites : Challenges, chemistry aspects, filler influences, and future insights
- 2021
-
Ingår i: Composites Part B. - : Elsevier. - 1359-8368 .- 1879-1069. ; 216
-
Forskningsöversikt (refereegranskat)abstract
- Resin-based dental composites are promising tooth-resembling materials in restorative dentistry. The limited longevity of dental composite restorations due to the bulk/marginal fracture and secondary caries as well as possible health risks are the critical challenges faced by such materials. Therefore, developments of resin-based dental composites received considerable attention in academic researches for clinical applications. A comprehensive review of the recent developments in the scientific literature on resin-based dental composites is presented in this article. Firstly, in the article, the challenges in dental composites are introduced and then the chemical aspects of the systems are classified through a review of employed resins. Subsequently, the different characteristics related to the fillers employed for the development of the resin-based dental composites are described. Finally, conclusions are drawn and future insights are proposed. This article provides an insight that paves the way for tailoring and designing resin-based dental composites for clinical applications.
|
|
| 4. |
- Aminoroaya, Alireza, et al.
(författare)
-
Facile encapsulation of cyanoacrylate-based bioadhesive by electrospray method and investigation of the process parameters
- 2024
-
Ingår i: Scientific Reports. - : Nature Research. - 2045-2322. ; 14:1
-
Tidskriftsartikel (refereegranskat)abstract
- Polymer microcapsules containing cyanoacrylates have represented a promising option to develop self-healing biomaterials. This study aims to develop an electrospray method for the preparation of capsules using poly(methyl methacrylate) (PMMA) as the encapsulant and ethyl 2-cyanoacrylate (EC) as the encapsulate. It also aims to study the effect of the electrospray process parameters on the size and morphology of the capsules. The capsules were characterized using Fourier-transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), and field-emission scanning electron microscopy (FE-SEM). Moreover, the effects of electrospray process parameters on the size were investigated by Taguchi experimental design. FTIR and TGA approved the presence of both PMMA and EC without further reaction. FE-SEM micrograph demonstrated that an appropriate choice of solvents, utilizing an appropriate PMMA:EC ratio and sufficient PMMA concentration are critical factors to produce capsules dominantly with an intact and spherical morphology. Utilizing various flow rates (0.3–0.5 ml/h) and applied voltage (18–26 kV), capsules were obtained with a 600–1000 nm size range. At constantly applied voltages, the increase in flow rate increased the capsule size up to 40% (ANOVA, p ≤ 0.05), while at constant flow rates, the increase in applied voltage reduced the average capsule size by 3.4–26% (ANOVA, p ≤ 0.05). The results from the Taguchi design represented the significance of solution flow rate, applied voltage, and solution concentration. It was shown that the most effective parameter on the size of capsules is flow rate. This research demonstrated that electrospray can be utilized as a convenient method for the preparation of sub-micron PMMA capsules containing EC. Furthermore, the morphology of the capsules is dominated by solvents, PMMA concentration, and PMMA:EC ratio, while the average size of the capsules can be altered by adjusting the flow rate and applied voltage of the electrospray process.
|
|
| 5. |
- Babu, Karthik, et al.
(författare)
-
A Review on the Flammability Properties of Carbon-Based Polymeric Composites : State-of-the-Art and Future Trends
- 2020
-
Ingår i: Polymers. - : MDPI. - 2073-4360. ; 12:7
-
Forskningsöversikt (refereegranskat)abstract
- Carbon based fillers have attracted a great deal of interest in polymer composites because of their ability to beneficially alter properties at low filler concentration, good interfacial bonding with polymer, availability in different forms, etc. The property alteration of polymer composites makes them versatile for applications in various fields, such as constructions, microelectronics, biomedical, and so on. Devastations due to building fire stress the importance of flame-retardant polymer composites, since they are directly related to human life conservation and safety. Thus, in this review, the significance of carbon-based flame-retardants for polymers is introduced. The effects of a wide variety of carbon-based material addition (such as fullerene, CNTs, graphene, graphite, and so on) on reaction-to-fire of the polymer composites are reviewed and the focus is dedicated to biochar-based reinforcements for use in flame retardant polymer composites. Additionally, the most widely used flammability measuring techniques for polymeric composites are presented. Finally, the key factors and different methods that are used for property enhancement are concluded and the scope for future work is discussed.
|
|
| 6. |
- Das, Oisik, et al.
(författare)
-
Flammability and mechanical properties of biochars made in different pyrolysis reactors
- 2021
-
Ingår i: Biomass and Bioenergy. - : Elsevier. - 0961-9534 .- 1873-2909. ; 152
-
Tidskriftsartikel (refereegranskat)abstract
- The effect of pyrolysis reactors on the properties of biochars (with a focus on flammability and mechanical characteristics) were investigated by keeping factors such as feedstock, carbonisation temperature, heating rate and residence time constant. The reactors employed were hydrothermal, fixed-bed batch vertical and fixed-bed batch horizontal-tube reactors. The vertical and tube reactors, at the same temperature, produced biochars having comparable elemental carbon content, surface functionalities, thermal degradation pattern and peak heat release rates. The hydrothermal reactor, although, a low-temperature process, produced biochar with high fire resistance because the formed tarry volatiles sealed water inside the pores, which hindered combustion. However, the biochar from hydrothermal reactor had the lowest nanoindentation properties whereas the tube reactor-produced biochar at 300 °C had the highest nanoindentation-hardness (290 Megapascal) and modulus (ca. 4 Gigapascal) amongst the other tested samples. Based on the inherent flammability and mechanical properties of biochars, polymeric composites’ properties can be predicted that can include them as constituents.
|
|
| 7. |
- Das, Oisik, et al.
(författare)
-
Functionalised biochar in biocomposites: The effect of fire retardants, bioplastics and processing methods
- 2023
-
Ingår i: Composites Part C: Open Access. - : Elsevier. - 2666-6820. ; 11
-
Tidskriftsartikel (refereegranskat)abstract
- Fire retardants, although can impart fire-safety in polymeric composites, are detrimental to the mechanical properties. Biochar can be used, in conjunction with fire retardants, to create a balance between fire-safety and mechanical performance. It is possible to thermally dope fire retardants into the pores of biochar to make it functionalised. Thus, the current work is intended in identifying a composite having the combination of the most desirable fire retardant, bioplastic, and a suitable processing method. A comparison was made between two fire retardants (lanosol and ammonium polyphosphate), bioplastics (wheat gluten and polyamide 11), and composite processing methods (compression and injection moulding). It was found that wheat gluten containing ammonium polyphosphate-doped biochar made by compression moulding had the best fire-safety properties with the lowest peak heat release rate (186 kW/m2), the highest fire performance index (0.6 m2s/kW), and the lowest fire growth index (1.6 kW/ms) with acceptable mechanical properties compared to the corresponding neat bioplastic. Thus, for gluten-based polymers, the use of ammonium polyphosphate thermally doped into biochar processed by compression moulding is recommended to both simultaneously improve fire-safety and conserve the mechanical strength of the resulting biocomposites.
|
|
| 8. |
- Das, Oisik, et al.
(författare)
-
Natural and industrial wastes for sustainable and renewable polymer composites
- 2022
-
Ingår i: Renewable & sustainable energy reviews. - : Elsevier BV. - 1364-0321 .- 1879-0690. ; 158
-
Tidskriftsartikel (refereegranskat)abstract
- By-products management from industrial and natural (agriculture, aviculture, and others) activities and products are critical for promoting sustainability, reducing pollution, increasing storage space, minimising landfills, reducing energy consumption, and facilitating a circular economy. One of the sustainable waste management approaches is utilising them in developing biocomposites. Biocomposites are eco-friendly materials because of their sustainability and environmental benefits that have comparable performance properties to the synthetic counterparts. Biocomposites can be developed from both renewable and industrial waste, making them both energy efficient and sustainable. Because of their low weight and high strength, biocomposite materials in applications such as automobiles can minimise fuel consumption and conserve energy. Furthermore, biocomposites in energy-based applications could lead to savings in both the economy and energy consumption. Herein, a review of biocomposites made from various wastes and their related key properties (e.g. mechanical and fire) are provided. The article systematically highlights the individual wastes/by-products from agriculture and materials processing industries for composites manufacturing in terms of their waste components (materials), modifications, resultant properties, applications and energy efficiency. Finally, a perspective for the future of biowastes and industrial wastes in polymer composites is discussed.
|
|
| 9. |
- Das, Oisik, et al.
(författare)
-
The Effect of Carbon Black on the Properties of Plasticised Wheat Gluten Biopolymer
- 2020
-
Ingår i: Molecules. - : MDPI. - 1431-5157 .- 1420-3049. ; 25:10
-
Tidskriftsartikel (refereegranskat)abstract
- Wheat gluten biopolymers generally become excessively rigid when processed without plasticisers, while the use of plasticisers, on the other hand, can deteriorate their mechanical properties. As such, this study investigated the effect of carbon black (CB) as a filler into glycerol-plasticised gluten to prepare gluten/CB biocomposites in order to eliminate the aforementioned drawback. Thus, biocomposites were manufactured using compression moulding followed by the determination of their mechanical, morphological, and chemical properties. The filler content of 4 wt% was found to be optimal for achieving increased tensile strength by 24%, and tensile modulus by 268% along with the toughness retention based on energy at break when compared with those of glycerol-plasticised gluten. When reaching the filler content up to 6 wt%, the tensile properties were found to be worsened, which can be ascribed to excessive agglomeration of carbon black at the high content levels within gluten matrices. Based on infrared spectroscopy, the results demonstrate an increased amount of β-sheets, suggesting the formation of more aggregated protein networks induced by increasing the filler contents. However, the addition of fillers did not improve fire and water resistance in such bionanocomposites owing to the high blend ratio of plasticiser to gluten.
|
|
| 10. |
- Das, Oisik, et al.
(författare)
-
The need for fully bio-based facemasks to counter coronavirus outbreaks : A perspective
- 2020
-
Ingår i: Science of the Total Environment. - : Elsevier. - 0048-9697 .- 1879-1026. ; 736
-
Tidskriftsartikel (refereegranskat)abstract
- The onset of coronavirus pandemic has sparked a shortage of facemasks in almost all nations. Without this personal protective equipment, healthcare providers, essential workers, and the general public are exposed to the risk of infection. In light of the aforementioned, it is critical to balance the supply and demand for masks. COVID-19 will also ensure that masks are always considered as an essential commodity in future pandemic preparedness. Moreover, billions of facemasks are produced from petrochemicals derived raw materials, which are non-degradable upon disposal after their single use, thus causing environmental pollution and damage. The sustainable way forward is to utilise raw materials that are side-stream products of local industries to develop facemasks having equal or better efficiency than the conventional ones. In this regard, wheat gluten biopolymer, which is a by-product or co-product of cereal industries, can be electrospun into nanofibre membranes and subsequently carbonised at over 700 °C to form a network structure, which can simultaneously act as the filter media and reinforcement for gluten-based masks. In parallel, the same gluten material can be processed into cohesive thin films using plasticiser and hot press. Additionally, lanosol, a naturally-occurring substance, imparts fire (V-0 rating in vertical burn test), and microbe resistance in gluten plastics. Thus, thin films of flexible gluten with very low amounts of lanosol (<10 wt%) can be bonded together with the carbonised mat and shaped by thermoforming to create the facemasks. The carbon mat acting as the filter can be attached to the masks through adapters that can also be made from injection moulded gluten. The creation of these masks could simultaneously be effective in reducing the transmittance of infectious diseases and pave the way for environmentally benign sustainable products.
|
|
