| 1. |
- Duoc, Vo Thanh, et al.
(författare)
-
New Design of ZnO Nanorod- and Nanowire-Based NO2 Room-Temperature Sensors Prepared by Hydrothermal Method
- 2019
-
Ingår i: Journal of Nanomaterials. - : HINDAWI LTD. - 1687-4110 .- 1687-4129.
-
Tidskriftsartikel (refereegranskat)abstract
- Room-temperature gas sensors are attracting attention because of their low power consumption, safe operation, and long-term stability. Herein, ZnO nanorods (NRs) and nanowires (NWs) were on-chip grown via a facile hydrothermal method and used for room-temperature NO2 gas sensor applications. The ZnO NRs were obtained by a one-step hydrothermal process, whereas the NWs were obtained by a two-step hydrothermal process. To obtain ZnO NW sensor, the length of NRs was controlled short enough so that none of the nanorod-nanorod junction was made. Thereafter, the NWs were grown from the tips of no-contact NRs to form nanowire-nanowire junctions. The gas-sensing characteristics of ZnO NRs and NWs were tested against NO2 gas at room temperature for comparison. The gas-sensing characteristics of the sensors were also tested at different applied voltages to evaluate the effect of the self-activated gas-sensing performance. Results show that the diameter of ZnO NRs and NWs is the dominant parameter of their NO2 gas-sensing performance at room temperature. In addition, self-activation by local heating occurred for both sensors, but because the NWs were smaller and sparser than the NRs, local heating thus required a lower applied voltage with maximal response compared with the NRs.
|
|
| 2. |
- Duy, Nguyen Van, et al.
(författare)
-
Design and fabrication of effective gradient temperature sensor array based on bilayer SnO2/Pt for gas classification
- 2022
-
Ingår i: Sensors and actuators. B, Chemical. - : Elsevier. - 0925-4005 .- 1873-3077. ; 351
-
Tidskriftsartikel (refereegranskat)abstract
- Classification of different gases is important, and it is possible to use different gas sensors for this purpose. Electronic noses, for example, combine separated gas sensors into an array for detecting different gases. However, the use of separated sensors in an array suffers from being bulky, high-energy consumption and complex fabrication processes. Generally, gas sensing properties, including gas selectivity, of semiconductor gas sensors are strongly dependent on their working temperature. It is therefore feasible to use a single device composed of identical sensors arranged in a temperature gradient for classification of multiple gases. Herein, we introduce a design for simple fabrication of gas sensor array based on bilayer Pt/SnO2 for real-time monitoring and classification of multiple gases. The study includes design simulation of the sensor array to find an effective gradient temperature, fabrication of the sensors and test of their performance. The array, composed of five sensors, was fabricated on a glass substrate without the need of backside etching to reduce heat loss. A SnO2 thin film sensitized with Pt on top deposited by sputtering was used as sensing material. The sensor array was tested against different gases including ethanol, methanol, isopropanol, acetone, ammonia, and hydrogen. Radar plots and principal component analysis were used to visualize the distinction of the tested gases and to enable effective classification.
|
|
| 3. |
- Hoang-Minh, Thao, et al.
(författare)
-
Mineralogical Characterization of Di Linh Bentonite, Vietnam: A Methodological Approach of X-ray Diffraction and Transmission Electron Microscopy
- 2014
-
Ingår i: Proceedings of 13th International Symposium on Mineral Exploration (ISME-XIII). - Hanoi : Vietnam National University Press, Hanoi. - 9786046215400 ; , s. 143-148
-
Konferensbidrag (refereegranskat)abstract
- Vietnam has decided to establish nuclear power as further energy option. In order to develop a Vietnamese reference bentonite as potential barrier in a final repository for high radioactive waste, a detailed mineralogical investigation of Di Linh bentonite (Lam Dong province), lacustrine clay, was carried out by different methods especially transmission electron microscopy (TEM) linked with energy-dispersive X-ray (EDX). From a sample homogenized from 5 tones of the bentonite, mineral formulae of clay particles was calculated The calculation also focuses on randomly interstratifications of two and three members. The fraction <2 μm of Di Linh bentonite is composed mainly by montmorillonite (Ca0.06Mg0.03Na0.09K0.03Al1.39Fe0.25Mg0.26(OH)2 Si3.96Al0.04O10) and regular ordering (R1) illite-smectite interstratifications with K- and charge-deficiency (Ca0.04Mg0.07Na0.18K0.16Al1.76Fe0.08Mg0.16(OH)2Si3.62Al0.38O10). Additionally, Fe-poor kaolinite-smectite-vermiculite interstratifications and trace of Fe-rich chloritesmectite- vermiculite interstatifications were identified. TEM-investigations showed analytical proofs of the sedimentary character of smectite formation in the Di Linh deposit. Parent muscovite was weathered in several steps in two different environments: (i) K-leaching and layer-wise alteration into kaolinite; (ii) further edge- controlled alteration of mica into lathlike montmorillonite particles under dissolution of kaolinite layers from former kaolinite-mica intergrowths. Mineralogical composition of the Di Linh bentonite with mainly montmorillonite and illite-rich illite-smectite interstratifications shows that the Di Linh bentonite can be a suitable barrier candidate in final repositories.
|
|
| 4. |
- Hoang-Minh, Thao, et al.
(författare)
-
Use of TEM-EDX for structural formula identification of clay minerals : a case study of Di Linh bentonite, Vietnam
- 2019
-
Ingår i: Journal of applied crystallography. - : International Union of Crystallography (IUCr). - 0021-8898 .- 1600-5767. ; 52:1, s. 133-147
-
Tidskriftsartikel (refereegranskat)abstract
- Transmission electron microscopy linked with energy-dispersive X-ray spectroscopy (TEM-EDX) was applied to characterize mineralogical signals ofweathering processes in the Di Linh bentonite deposit (Vietnam) and to visualize the effects of Na activation on the smectitic phases. Modelling of X ray diffraction patterns (oriented mount) was applied in order to refine the computed structural formula. X-ray diffraction, X-ray fluorescence and Fouriertransform infrared spectroscopy (FT-IR) methods were also applied to verify the TEM-EDX results. An Excel-based routine has been developed in this research to allow fast computation of structural formulae and classification of the investigated clay particles. This routine supports the acquirement of 100 300 TEM-EDX analyses as a representative set of individual particles for each sample. The Excel-based routine involves end members of different clay mineral groups and interstratifications with two or three members (e.g. illite smectite interstratifications – IS-ml; dioctahedral vermiculite–smectite interstratifications – diVS-ml; and kaolinite–montmorillonite–dioctahedral vermiculite interstratifications – KSV-ml). The routine is now freely available. According to the identification procedure, the <2 mm fraction of the Di Linh bentonite (Vietnam) is composed mainly of K- and charge-deficient illite smectite interstratifications (or diVS-ml): montmorillonite-rich randomly ordered (R0) type and illite-rich regularly ordered (R1) type. Additionally, Fe-poor KSV-ml was identified.Industrial Na activation of the Di Linh bentonite resulted in an increase of theR1 diVS-ml portion and dissolution of a large part of the smectite-rich phases.The TEM-EDX approach also gave analytical proof of a sedimentary processfor Di Linh smectite. The parent muscovite was altered in two different environments: (i) K-leaching and layer-wise alteration into kaolinite (weathering), and (ii) further edge-controlled alteration of mica into lath-like montmorillonite particles associated with a dissolution of kaolinite layers from the former kaolinite–mica intergrowths by heat impact (basalt flow).
|
|
| 5. |
- Phu, Vu Dinh, et al.
(författare)
-
Burden of Hospital Acquired Infections and Antimicrobial Use in Vietnamese Adult Intensive Care Units
- 2016
-
Ingår i: PLOS ONE. - : PUBLIC LIBRARY SCIENCE. - 1932-6203. ; 11:1
-
Tidskriftsartikel (refereegranskat)abstract
- Background Vietnam is a lower middle-income country with no national surveillance system for hospital-acquired infections (HAIs). We assessed the prevalence of hospital-acquired infections and antimicrobial use in adult intensive care units (ICUs) across Vietnam. Methods Monthly repeated point prevalence surveys were systematically conducted to assess HAI prevalence and antimicrobial use in 15 adult ICUs across Vietnam. Adults admitted to participating ICUs before 08: 00 a.m. on the survey day were included. Results Among 3287 patients enrolled, the HAI prevalence was 29.5% (965/3266 patients, 21 missing). Pneumonia accounted for 79.4% (804/1012) of HAIs Most HAIs (84.5% [855/1012]) were acquired in the survey hospital with 42.5% (363/855) acquired prior to ICU admission and 57.5% (492/855) developed during ICU admission. In multivariate analysis, the strongest risk factors for HAI acquired in ICU were: intubation (OR 2.76), urinary catheter (OR 2.12), no involvement of a family member in patient care (OR 1.94), and surgery after admission (OR 1.66). 726 bacterial isolates were cultured from 622/1012 HAIs, most frequently Acinetobacter baumannii (177/726 [24.4%]), Pseudomonas aeruginosa (100/726 [13.8%]), and Klebsiella pneumoniae (84/726 [11.6%]), with carbapenem resistance rates of 89.2%, 55.7%, and 14.9% respectively. Antimicrobials were prescribed for 84.8% (2787/ 3287) patients, with 73.7% of patients receiving two or more. The most common antimicrobial groups were third generation cephalosporins, fluoroquinolones, and carbapenems (20.1%, 19.4%, and 14.1% of total antimicrobials, respectively). Conclusion A high prevalence of HAIs was observed, mainly caused by Gram-negative bacteria with high carbapenem resistance rates. This in combination with a high rate of antimicrobial use illustrates the urgent need to improve rational antimicrobial use and infection control efforts.
|
|
| 6. |
- Son, Dang Ngoc, et al.
(författare)
-
A novel design and fabrication of self-heated In2O3 nanowire gas sensor on for ethanol detection
- 2022
-
Ingår i: Sensors and Actuators A-Physical. - : Elsevier. - 0924-4247 .- 1873-3069. ; 345
-
Tidskriftsartikel (refereegranskat)abstract
- Many attempts have been made on the design and fabrication of low-power consumption gas sensor for application on the Internet of Things and portable devices. The performance of gas sensors includes sensitivity, selectivity, and power consumption, which are strongly dependent on the configuration of the device such as the gap size between two electrodes, the sensing material, and operation principle. Here, self-heated In2O3 nanowire-based gas sensors were designed and fabricated by on-chip growth technique via thermal evaporation to work at room temperature. The effect of electrode gap (10-40 mu m) on the power consumption and gas sensing performance of the In2O3 nanowire sensors was studied. With the large gap of 40 mu m, the sensor exhibited excellent sensing characteristics of low power consumption (1.06 mW) with ability to detect ethanol gas down to 20 ppm effectively. We also examined the role of nanowire conductivity in the performance of the self-heated sensor in the detection of reducing gas. The sensor demonstrated rapid response and recovery times of less than a minute, exceptional stability, and remarkable recovery.
|
|
| 7. |
- Thanh Le, Thanh, et al.
(författare)
-
Diarylether-Amino Acid Conjugates as New Class of Anticancer Agents
- 2023
-
Ingår i: CHEMISTRYSELECT. - : Wiley. - 2365-6549. ; 8:28
-
Tidskriftsartikel (refereegranskat)abstract
- Diarylether (DE) is a privileged structure found in both natural products and synthetic compounds including small molecule drugs. We present the synthesis of a series of 13 new DE-amino acid conjugates which were screened for cancer cells antiproliferation activity. Structure-activity relationship suggests ester and phenyl groups in DE-Phe-OEt 4 c are important for the activity. Compound 4 c inhibited strongly MCF-7 3D tumor sphere formation and have favourable calculated physical chemical properties according to Lipinski's rule of 5. Docking study suggests estrogen receptor and/ or 3a-HSD type 3 protein could be the target(s) for anticancer activity of this class of compounds.
|
|
| 8. |
- Duoc, Vo Thanh, et al.
(författare)
-
Room temperature highly toxic NO2 gas sensors based on rootstock/scion nanowires of SnO2/ZnO, ZnO/SnO2, SnO2/SnO2 and, ZnO/ZnO
- 2021
-
Ingår i: Sensors and actuators. B, Chemical. - : Elsevier. - 0925-4005 .- 1873-3077. ; 348
-
Tidskriftsartikel (refereegranskat)abstract
- Grafted structures between SnO2 and ZnO nanowires were realized in a two-step process of growth. First, the rootstocks of SnO2 or ZnO nanowires were synthesized by thermal evaporation technique. Second, a thin Au layer was sputter deposited on the sample and synthesis of nanowire scions of ZnO or SnO2, respectively, on the rootstocks was realized by thermal evaporation technique again. In both growth steps, SnO2 powder or a mixture of ZnO and carbon powders was use as source materials for the synthesis. Different rootstock/scion combinations of SnO2/ZnO, ZnO/SnO2 nanowires (called heterostructures) and ZnO/ZnO, SnO2/SnO2 nanowires (called homostructures) were synthesised. The fabricated grafted nanowires were examined by field-emission scanning electron microscope and their compositions were analyzed by energy dispersive spectroscopy and X-ray diffraction analysis. The test results indicate that this type of nanostructure material is very promising for NO2 gas sensing at ppt level at room temperature. Among the fabricated structures the SnO2/ZnO nanowires showed the best sensing performance with the high sensitivity and fast response and recovery time. We also discussed the gas sensing mechanism of the fabricated sensors based on the band diagram.
|
|
| 9. |
- Thanh Hoan, Nguyen, et al.
(författare)
-
Novel Time Series Bagging Based Hybrid Models for Predicting Historical Water Levels in the Mekong Delta Region, Vietnam
- 2022
-
Ingår i: CMES - Computer Modeling in Engineering & Sciences. - : Tech Science Press. - 1526-1492 .- 1526-1506. ; 131:3, s. 1431-1449
-
Tidskriftsartikel (refereegranskat)abstract
- Water level predictions in the river, lake and delta play an important role in flood management. Every year Mekong River delta of Vietnam is experiencing flood due to heavy monsoon rains and high tides. Land subsidence may also aggravate flooding problems in this area. Therefore, accurate predictions of water levels in this region are very important to forewarn the people and authorities for taking timely adequate remedial measures to prevent losses of life and property. There are so many methods available to predict the water levels based on historical data but nowadays Machine Learning (ML) methods are considered the best tool for accurate prediction. In this study, we have used surface water level data of 18 water level measurement stations of the Mekong River delta from 2000 to 2018 to build novel time-series Bagging based hybrid ML models namely: Bagging (RF), Bagging (SOM) and Bagging (M5P) to predict historical water levels in the study area. Performances of the Bagging-based hybrid models were compared with Reduced Error Pruning Trees (REPT), which is a benchmark ML model. The data of 19 years period was divided into 70:30 ratio for the modeling. The data of the period 1/2000 to 5/2013 (which is about 70% of total data) was used for the training and for the period 5/2013 to 12/2018 (which is about 30% of total data) was used for testing (validating) the models. Performance of the models was evaluated using standard statistical measures: Coefficient of Determination (R2), Root Mean Square Error (RMSE) and Mean Absolute Error (MAE). Results show that the performance of all the developed models is good (R2 > 0.9) for the prediction of water levels in the study area. However, the Bagging-based hybrid models are slightly better than another model such as REPT. Thus, these Bagging-based hybrid time series models can be used for predicting water levels at Mekong data.
|
|
| 10. |
- Chu Manh, Hung, et al.
(författare)
-
ZnO coral-like nanoplates decorated with Pd nanoparticles for enhanced VOC gas sensing
- 2021
-
Ingår i: Journal of Science: Advanced Materials and Devices. - Hanoi, Vietnam : Elsevier. - 2468-2284 .- 2468-2179. ; 6:3, s. 453-461
-
Tidskriftsartikel (refereegranskat)abstract
- A high working temperature of the ZnO nanomaterial-based gas sensor could shorten the lifetime of the sensor and increase its power consumption. Enhancing the volatile organic compound (VOC) sensing performance of ZnO nanomaterial-based gas sensors in terms of gas response and temperature is vital for their practical application. Decoration of noble metals onto nanostructures is an effective approach for improving their sensing characteristics. Herein, hydrothermally synthesized ZnO coral-like nanoplates decorated with Pd nanoparticles are introduced to achieve the improved VOC sensing performance. The morphology, crystal structure, composition, atomic structure, and gas sensing properties of the synthesized pristine and Pd–ZnO coral-like nanoplates were investigated. The results showed a remarkable reduction of optimal working temperature from 450 °C for the pristine ZnO based sensor to 350 °C for the Pd–ZnO based sensor. The sensor response to acetone at the optimal operating temperature of 350 °C was improved three times by surface decoration with Pd nanoparticles. The response time and recovery time of the Pd–ZnO sensor were about three times faster than that of the pristine ZnO sensor. The Pd–ZnO sensor reached a theoretical detection limit of 17 ppt and a sensitivity of 3.5–2.5 ppm acetone at 350 °C. The sensor transient stability after several on/off switching cycles from air to gas revealed the effective reusability of the fabricated devices. A plausible mechanism for the VOC sensing of the porous Pd–ZnO coral-like nanoplate-based sensor is also discussed.
|
|
