| 1. |
- Bremer, Johan, 1991, et al.
(författare)
-
Analysis of Lateral Thermal Coupling for GaN MMIC Technologies
- 2018
-
Ingår i: IEEE Transactions on Microwave Theory and Techniques. - 0018-9480 .- 1557-9670. ; 66:10, s. 4430-4438
-
Tidskriftsartikel (refereegranskat)abstract
- This paper presents a study of the lateral heat propagation in an aluminum gallium nitride/gallium nitride (AlGaN/GaN) heterostructure grown on a silicon carbide substrate. The study is enabled by the design of a temperature sensor that utilizes the temperature-dependent I-V characteristic of a semiconductor resistor, making it suitable for integration in GaN monolithic microwave integrated circuit technologies. Using the sensor, we are able to characterize the thermal transient response and extract lateral thermal time constants from the measurements. Time constants in the range from 25 mu s to 1.2 ms are identified. Furthermore, the heat propagation properties are characterized for heat source-to-sensor distances of 86-484 mu m, resulting in delay times from 3.5 to 111 mu s. It is shown that both the time constants and propagation delay increase with temperature. An empirical model of the sensor current versus temperature and voltage is proposed and used to predict the junction temperature of the sensor. The study provides knowledge for heat management design and proposes an integrated temperature measurement solution for future highly integrated GaN applications.
|
|
| 2. |
- Bremer, Johan, 1991, et al.
(författare)
-
Electric-Based Thermal Characterization of GaN Technologies Affected by Trapping Effects
- 2020
-
Ingår i: IEEE Transactions on Electron Devices. - 1557-9646 .- 0018-9383. ; 67:5, s. 1952-1958
-
Tidskriftsartikel (refereegranskat)abstract
- This article presents an electric-based methodology for thermal characterization of semiconductor technologies. It is shown that for technologies such as gallium nitride (GaN) high electron mobility transistors, which exhibit several field induced electron trapping effects, the thermal characterization has to be performed under specific conditions. The electric field is limited to low levels to avoid activation of trap states. At the same time, the dissipated power needs to be high enough to change the operating temperature of the device. The method is demonstrated on a test structure implemented as a GaN resistor with large contact separation. It is used to evaluate the thermal properties of samples with different silicon carbide suppliers and buffer thickness.
|
|
| 3. |
- Enmark, Markus, 1991, et al.
(författare)
-
A Critical Assessment of Nano Enhanced Vapor Chamber Wick Structures for Electronics Cooling
- 2021
-
Ingår i: 2021 23rd European Microelectronics and Packaging Conference and Exhibition, EMPC 2021.
-
Konferensbidrag (refereegranskat)abstract
- The increasing need for high thermal dissipation in small electronic products puts tough requirements on effective cooling solutions. Two of the most effective passive cooling devices in electronics today are vapor chambers and heat pipes. With new advancements in materials science and nanotechnology comes the possibility to further increase cooling capacity and at the same time make devices lighter. This study is a critical assessment on recent progress in the field of nanomaterial enhanced wick structures in vapor chambers and heat pipes. In this paper, nano-enhanced wick structures are divided into five different sub-categories based on material type. Publication trends for the different types of nano-enhanced wicks are studied by plotting them on a timeline. It is found that nanostructured metal wicks is the most studied field in recent years. A plot showing wick performance in terms of superheat temperatures for given heat flux is created to be used for benchmarking of new wick structures when pool boil experiments are carried out. An attempt to find correlation between publication trends, type of wick and performance is done. On the basis of the gathered data it is deemed difficult to find a distinct correlation, this is mainly due to difficulty in comparing performance between different studies, especially when different heat fluxes are used. There is no unambiguous answer to which category of nano-enhanced wicks that should be target for future studies. Graphene coating and pure carbon nanomaterials such as aerogels and graphene foam are still relatively unexplored and believed to have great potential if they can be attached to envelope materials.
|
|
| 4. |
- Hansson, Josef, 1991, et al.
(författare)
-
Bipolar electrochemical capacitors using double-sided carbon nanotubes on graphite electrodes
- 2020
-
Ingår i: Journal of Power Sources. - : Elsevier BV. - 0378-7753. ; 451
-
Tidskriftsartikel (refereegranskat)abstract
- The electrochemical capacitor (EC) is a key enabler for the miniaturized self-powered systems expected to become ubiquitous with the advent of the internet-of-things (IoT). Vertically aligned carbon nanotubes (VACNTs) on graphite holds promise as electrodes for compact and low-loss ECs. However, as with all ECs, the operating voltage is low, and miniaturization of higher voltage devices necessitates a bipolar design. In this paper, we demonstrate a bipolar EC using graphite/VACNTs electrodes fabricated using a joule heating chemical vapor deposition (CVD) setup. The constructed EC contains one layer of double-sided VACNTs on graphite as bipolar electrode. Compared to a series connection of two individual devices, the bipolar EC has 22% boost in volumetric energy density. More significant boost is envisaged for stacking more bipolar electrode layers. The energy enhancement is achieved without aggravating self-discharge (71.2% retention after 1 h), and at no sacrifice of cycling stability (96.7% over 50000 cycles) owing to uniform growth of VACNTs and thus eliminating cell imbalance problems.
|
|
| 5. |
- Hansson, Josef, 1991, et al.
(författare)
-
Effect of Fiber Concentration on Mechanical and Thermal Properties of a Solder Matrix Fiber Composite Thermal Interface Material
- 2019
-
Ingår i: IEEE Transactions on Components, Packaging and Manufacturing Technology. - 2156-3985 .- 2156-3950. ; 9:6, s. 1045-1053
-
Tidskriftsartikel (refereegranskat)abstract
- Increased demand on the mechanical and thermal properties on the thermal interface and die attach material creates a demand for materials with tailored material properties. Solder matrix fiber composites (SMFCs) have been shown to address these challenges, but have, so far, required complicated procedures and components. In this paper, we present the fabrication of a new type of SMFC based on commercially available fiber networks infiltrated with Sn-Ag-Cu alloy (SAC305) or indium using equipment for large-volume production. The composite material exhibits similar thermal properties compared to pure solder, and mechanical properties that can be tailored toward specific applications. We also show that the handling properties of the SMFC allows it to be used in process flows where multiple reflow cycles are required and can achieve a well-defined bond line thickness (BLT) and good bonding using fluxless reflow under pressure.
|
|
| 6. |
- Hansson, Josef, 1991, et al.
(författare)
-
Effects of high temperature treatment of carbon nanotube arrays on graphite : Increased crystallinity, anchoring and inter-tube bonding
- 2020
-
Ingår i: Nanotechnology. - : Institute of Physics Publishing (IOPP). - 0957-4484 .- 1361-6528. ; 31:45
-
Tidskriftsartikel (refereegranskat)abstract
- Thermal treatment of carbon nanotubes (CNTs) can significantly improve their mechanical, electrical and thermal properties due to reduced defects and increased crystallinity. In this work we investigate the effect of annealing at 3000 degrees C of vertically aligned CNT arrays synthesized by chemical vapor deposition (CVD) on graphite. Raman measurements show a drastically reduced amount of defects and, together with transmission electron microscope (TEM) diffraction measurements, an increased average crystallite size of around 50%, which corresponds to a 124% increase in Young's modulus. We also find a tendency for CNTs to bond to each other with van der Waals (vdW) forces, which causes individual CNTs to closely align with each other. This bonding causes a densification effect on the entire CNT array, which appears at temperatures >1000 degrees C. The densification onset temperature corresponds to the thermal decomposition of oxygen containing functional groups, which otherwise prevents close enough contact for vdW bonding. Finally, the remaining CVD catalyst on the bottom of the CNT array is evaporated during annealing, enabling direct anchoring of the CNTs to the underlying graphite substrate.
|
|
| 7. |
- Hansson, Josef, 1991, et al.
(författare)
-
Novel nanostructured thermal interface materials: a review
- 2018
-
Ingår i: International Materials Reviews. - : Informa UK Limited. - 0950-6608 .- 1743-2804. ; 63:1, s. 22-45
-
Forskningsöversikt (refereegranskat)abstract
- The trend of continuing miniaturisation of microelectronics leads to new thermal management challenges. A key point in the heat removal process development is to improve the heat conduction across interfaces through improved thermal interface materials (TIMs). We identify the key areas for state-of-the art TIM research and investigate the current state of the field together with possible future advances.
|
|
| 8. |
- Hansson, Josef, 1991, et al.
(författare)
-
Synthesis of a Graphene Carbon Nanotube Hybrid Film by Joule Self-heating CVD for Thermal Applications
- 2018
-
Ingår i: Proceedings - Electronic Components and Technology Conference. - 0569-5503. ; 2018-May
-
Konferensbidrag (refereegranskat)abstract
- Hybrid films based on vertically aligned carbon nanotubes (CNTs) on graphene or graphite sheets have been proposed for application as thermal interface materials and micro heat sinks. However, the fabrication of these materials are limited to small scale, expensive and complicated chemical vapor deposition (CVD) for CNT synthesis. We present a new method for direct growth of CNTs on one or both sides of a thin graphene film (GF) using joule self-heating of the graphene film to provide the necessary heat for the thermal breakdown of carbon feedstock in a CVD process. The resulting CNT forests show good density and alignment consistent with regular CVD synthesis processes on silicon surfaces. The resulting double sided GF/CNT hybrid film is directly applicable as a thermal pad. The CNT forest has a thermal conductivity of 30 W/mK, measured by pulsed photothermal reflectance, and the total thermal interface resistance between aluminum blocks was measured to be 60 Kmm 2 /W using an ASTM D5470 compliant 1-D measurement setup. This method of directly synthesizing CNTs on graphene films is more energy efficient and capable of larger volume production compared to traditional CVD methods. It is also compatible with scaling up towards continuous roll-to-roll production for large scale commercial production, one of the major limitations preventing CVD-grown CNTs from commercial applications
|
|
| 9. |
- Hultdin, Johan, et al.
(författare)
-
Prospective study of first stroke in relation to plasma homocysteine and MTHFR 677C > T and 1298A > C genotypes and haplotypes : evidence for an association with hemorrhagic stroke
- 2011
-
Ingår i: Clinical Chemistry and Laboratory Medicine. - Berlin : Walter de Gruyter. - 1434-6621 .- 1437-4331. ; 49:9, s. 1555-1562
-
Tidskriftsartikel (refereegranskat)abstract
- Background: Abnormalities in homocysteine metabolism have been suggested as risk factors for stroke. The aim of this prospective study was to examine whether total plasma homocysteine concentration (tHcy) and its main genetic determinant, methylene tetrahydrofolate reductase (MTHFR) polymorphisms, were associated with first ischemic or hemorrhagic stroke.Methods: This was a nested case-referent study of 321 ischemic and 60 hemorrhagic stroke cases, defined by WHO MONICA criteria and each matched with two event-free referents for sex, age, cohort, recruitment date and geographical area. All subjects were from the population-based Northern Sweden Health and Disease Study cohorts. Odds ratios were determined by conditional logistic regression.Results: The mean follow-up time was 4.2 years. Both tHcy and MTHFR were independent predictors of hemorrhagic stroke in multivariate models including body mass index, hypertension and, for MTHFR, tHcy [OR for the highest vs. lowest tHcy quartile 8.13 (95% CI 1.83-36.1), p(trend)=0.002; OR for MTHFR 677TT vs. 677CC genotype 3.62 (95% CI 0.77-17.0), p(trend)=0.040]. Haplotype analyses confirmed that the MTHFR 677T-1298A haplotype was positively associated with hemorrhagic stroke [OR 1.81 (95% CI 1.09-3.00), p=0.022], whereas the MTHFR 677C-1298C haplotype was not significantly related to either hemorrhagic or ischemic stroke. Neither tHcy nor the MTHFR polymorphisms were significant predictors of ischemic stroke.Conclusion: Both elevated plasma homocysteine levels and the MTHFR 677T allele are indicators of increased risk of hemorrhagic stroke in the northern Swedish population.
|
|
| 10. |
- Kabiri Samani, Majid, 1976, et al.
(författare)
-
Improving Thermal Transport at Carbon Hybrid Interfaces by Covalent Bonds
- 2018
-
Ingår i: Advanced Materials Interfaces. - : Wiley. - 2196-7350. ; 5:15
-
Tidskriftsartikel (refereegranskat)abstract
- Graphene and carbon nanotubes have received much attention for thermal management application due to their unique thermal performance. Theoretical work suggests that a covalent bond can combine 1D carbon nanotubes with 2D graphene together to extend the excellent thermal property to three dimensions for heat dissipation. This paper experimentally demonstrates the high heat dissipation capability of a freestanding 3D multiwall carbon nanotube (MWCNT) and graphene hybrid material. Using high-resolution transmission electron microscopy and pulsed photothermal reflection measurement method, the covalent bonds between MWCNT and planar graphene are microscopically and numerically demonstrated. Thermal resistance at the junction with covalent bonds is 9×10^−10 Kelvin square meter per watt, which is three orders of magnitude lower than van der Waals contact. Joule heating method is used to verify the extra cooling effect of this 3D hybrid material compared to graphite film. A demonstrator using high power chip is developed to demonstrate the applicability of this hybrid material in thermal application. Temperature at hot spots can be decreased by around 10°C with the assistance of this hybrid material. These findings are very significant for understanding the thermal conduction during combining 1D and 2D carbon material together for future thermal management application.
|
|
