| 1. |
- Andrén, Anna, et al.
(författare)
-
Degradation of the Reinforcing Effect of Shotcrete : Freeze-Thaw Tests on Shotcrete-Rock Panels
- 2020
-
Ingår i: The Electronic journal of geotechnical engineering. - : Mete Öner. - 1089-3032 .- 1089-3032. ; 25:1, s. 1-30
-
Tidskriftsartikel (refereegranskat)abstract
- In rock tunnels in regions with colder climates, the load-bearing structure, including the rock and the reinforcing elements, is exposed to repeated destructive freezing and thawing cycles during the winter. If water accumulates in cracks or in the interface between rock and shotcrete, frost shattering may occur. If there is adequate adhesion between the rock and shotcrete, degradation of the shotcrete as a reinforcement element due to frost shattering should not present a problem. However, if adhesion is poor, a small void will form between the rock and the shotcrete where water can accumulate. If the water in these voids is subjected to freeze-thaw cycles, ice will develop, thus exerting pressure on the interface and causing the shotcrete to crack and degrade. In tunnel sections with complex water conditions, for example, relatively water-bearing open joints and weak zones, the adhesion of the shotcrete and its stability and reinforcing effect may be strongly affected when exposed to freezing temperatures. This article describes a laboratory study that comprised freeze-thaw tests on shotcreterock panels with the objective of studying how water migration affects the growth of ice and the ice pressure in the shotcrete-rock interface to better understand the degradation of the reinforcing effect of shotcrete
|
|
| 2. |
- Andrén, Anna, et al.
(författare)
-
Evaluation of a laboratory model test using field measurements of frost penetration in railway tunnels
- 2022
-
Ingår i: Cold Regions Science and Technology. - : Elsevier. - 0165-232X .- 1872-7441. ; 204
-
Tidskriftsartikel (refereegranskat)abstract
- Despite extensive grouting efforts to prevent water from leaking into tunnels, water seepages remain. When exposed to freezing temperatures, ice formations occur. During the winter, the Swedish Transport Administration's railway tunnels are affected by major problems caused by ice, such as icicles from roof and walls, ice loads on installations, ice-covered tracks and roads, etc. To ensure safety and prevent traffic disruptions, many tunnels require extensive maintenance. Improved knowledge about frost penetration in tunnels is required to reduce maintenance of the tunnels. Frost insulated drain mats are often used at leakage spots to prevent ice formation along the tunnels. To find out which parts of a tunnel are exposed to freezing temperatures, the University of Gävle and the Royal Institute of Technology in Stockholm conducted a laboratory model test on behalf of the Swedish National Rail Administration (now the Swedish Transport Administration). The laboratory model test aimed to find a method to determine the expected temperature conditions along a tunnel to decide which parts of the tunnel require frost insulation to protect the drainage system from freezing and prevent ice formation. To evaluate the laboratory model test, the Swedish Transport Administration in collaboration with Luleå University of Technology have performed field surveys in two Swedish railway tunnels. The field measurements involved monitoring temperatures in air, rock surfaces and rock mass, as well as measuring wind direction, wind and air velocity and air pressure. The measurements in the tunnels show that the frost penetrates further into the tunnels than was expected from the laboratory model test, which was based on a completely uninsulated tunnel. Frost insulated drains do not only prevent the cold air from reaching the rock mass, but also prevent the rock from emitting geothermal heat that warms up the cold tunnel air. Consequently, the frost penetrates further into the tunnel than it would do if the heat from the rock mass was allowed to warm up the outside air on its way into the tunnel. The number of frost insulated drains and how much of the tunnel walls and roof are covered thereby affect the length of the frost penetration.
|
|
| 3. |
- Andrén, Anna, et al.
(författare)
-
Field Observations of Water and Ice Problems in Railway Tunnels from a Maintenance Perspective
- 2023
-
Ingår i: Journal of Earth Sciences and Geotechnical Engineering. - : Scientific Press International Limited. - 1792-9040 .- 1792-9660. ; 13:1, s. 11-54
-
Tidskriftsartikel (refereegranskat)abstract
- During the winter season, ice causes major problems in many Swedish railway tunnels. Ice, rock and shotcrete in the roof and on the walls may come loose and fall down, installations and cables can break due to ice loads and the tracks can become covered with ice. To maintain safety and prevent traffic disturbances, many tunnels require frequent maintenance. The removal of ice, loose rock and shotcrete is expensive and potentially risky work for the maintenance workers. To reduce maintenance costs, it is important to improve our knowledge of frost penetration inside tunnels and investigate the effect of ice pressure and frost shattering on loadbearing constructions. The aim of this investigation was to gather information about the problems caused by water leakage and its effect on the degradation of a rock tunnel when subjected to freezing temperatures. There are many factors that determine whether frost or ice formations will appear in tunnels. To collect information on ice formation problems, field observations were undertaken in five of Sweden’s railway tunnels between autumn 2004 and summer 2005. For one of the tunnels, follow-up observations also took place in March during the years 2005, 2006 and 2007.
|
|
| 4. |
- Andrén, Anna, 1970-
(författare)
-
Freezing Temperature Flows in Railway Tunnels and its Consequence on the Rock Supporting Structure, the Rock and the Reinforcing Elements
- 2023
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Water in the surrounding rock mass flows into the tunnel via naturally occurring joints and via cracks caused by the blasting used to excavate the tunnel. The most common method in Sweden to reduce or prevent leakage problems are first and foremost the use of grouting. However, experience shows that despite extensive pre-grouting and supplementary post-grouting, it is difficult to seal the rock mass so that drips and moisture are completely eliminated. Although the water itself causes degradation of the tunnel, the degradation process increases dramatically when the water is exposed to freezing temperatures. Water expands during freezing and due to water migration, which occurs in rock in a similar way as in soil, the ice causes frost shattering of the interface between rock and shotcrete and also to the shotcrete and the rock itself. This can damage the main load-bearing system. The ice formation itself is a maintenance problem, as the tunnels must be kept clear of icicles, ice pillars and ice layers in the tracks or on the roads. One of the main tasks in this research project has been to identify which problems cause the most maintenance work and where and when these problems occur in the tunnel.During the field observations carried out as part of this doctoral study, many problems with water and ice were discovered, all of which contribute to increased maintenance. Many ice problems are directly linked to frost insulated drain mats. Leakage and ice formations occur at the edge of the drains, in mat splices and when brackets for cable racks, handrails or other installations puncture a drain and it has not been properly sealed. In drains covered with shotcrete, frost shattering and cracking in the shotcrete can be a problem. Frost cycles in the tunnel cause the water to freeze and thaw alternately, allowing more water to reach the freezing area due to water migration, resulting in frost shattering of the rock and the shotcrete. If not anchored with bolts, the reinforcing effect and the stability of shotcrete in a tunnel is dependent on the adhesion to the rock surface. It is, therefore, important to take all available measures to ensure good adhesion. Poor adhesion in itself is not a degradation problem, but a void can form in the interface between rock and shotcrete as a result of poor adhesion. If this void is filled with water that cannot drain away, ice pressure can occur in the layer between rock and shotcrete. The ice pressure can cause cracking and degradation of the shotcrete if the pressure exceeds the tensile strength of the adjacent material. In some of the reported fall-outs of rock and shotcrete, an ice layer was discovered between the rock surface and the edges of the remaining shotcrete layer. Therefore, frost shattering is a likely cause of the fall-outs. Many frost cycles combined with water leakage can cause frost shattering. The field measurements conducted as a part of the doctoral study have shown that most frost cycles do not occur closest to the tunnel entrances, but instead about 100 to 200 m into the longer tunnels. The results from the laboratory tests performed as part of the doctoral study showed that the adhesive strength between rock and shotcrete decreased significantly when the test panels were subjected to freeze-thaw cycles. Furthermore, more of the micro seismic events (AE - acoustic emission monitoring) occurred in the test panels that had access to water during freezing. Therefor, maintenance personnel and inspectors should pay particular attention to water leakage in sections that have an increased number of frost cycles, to avoid future problems with frost shattering of rock or shotcrete. In the longer tunnels studied in this work, a greater number of ice formations occurred in the inner parts of the tunnel, than close to the entrances. The rock mass emits heat, which heats up the cold outside air that enters the tunnel. Due to the heat transfer from the rock mass, leakage points located further along the tunnels can remain unfrozen. A leak that is closer to the tunnel entrances in the longer tunnels or a leak in a shorter tunnel are exposed to higher freezing rates. The entire rock mass freezes and the leak ‘freezes dry’, that is, ice forms in the water-bearing fracture, preventing further water leakage.Where and when ice problems occur along a tunnel depends on many factors. Besides the obvious water leakage, the length of frost penetration into the tunnel is the main reason for where and when ice problems occur. The predominant cause of frost penetration in most of the tunnels is the thermally induced airflow. In the longer tunnels, the inclination of the tunnel affects frost penetration the most. The field observations showed that there was a difference in where and when leakage points appear during the year and also in terms of variation in the amount of leakage water. There was also a variation over different years. The conclusions of the field observations are that it is difficult to estimate where the insulated drain mats should be located along a tunnel. Based on experience from this survey, the location of the drains should be determined only after several inspections and especially after a winter period, when the main problems with ice formation occur. Previous perception regarding ice problems have been that ice formation only occurs at the tunnel entrances and in the outer parts of the tunnel. A proposed measure has, therefore, been to cover the first 300 m from each entrance with frost insulated drains to try to completely eliminate the ice problems. However, this is not an effective solution to the problem. The insulation not only prevents the cold from reaching the leakage point, but it also prevents the rock mass from emitting heat that warms up the cold outside air entering the tunnel. Thus, the frost can penetrate further into the tunnel and the problems with ice formation are only moved further into the tunnel. As the amount and location of the frost insulation affects frost penetration, the dimensioning of insulation must, therefore, be carried out in several iterations, where each new distribution of insulation along the tunnel is calculated separately.For the tunnels that have been studied as part of this doctoral study, the following has emerged. The central and southern parts of Sweden have shorter cooling periods and the tunnels are exposed to many temperature fluctuations around 0°C during the winter. The frost does not have time to penetrate as far here as in the tunnels in the northern parts of Sweden. Therefore, more ice problems arise around the entrances of the tunnels in the southern parts of Sweden than for those in the northern parts. For northern parts of Sweden, the problem of growing ice formations in sections near the tunnel entrance usually occurs only during the autumn and spring, but not in winter. The field observations showed that the problems with ice growth and temperature fluctuations around 0°C occur further along the longer tunnels in the northern parts of Sweden. This is because the temperature of the tunnel air is higher due to heat transfer from the rock mass. For shorter tunnels that adopt the same temperatures as the outside air, ice formations can occur along the entire length of the tunnel in the sections that have leakage problems. The Swedish Transport Administration’s regulations are currently being updated and the observations and measurements carried out in this doctoral work are now being used to evaluate new requirements regarding frost penetration in tunnels.
|
|
| 5. |
- Andrén, Anna, et al.
(författare)
-
Temperature Flows in Railway Tunnels : Field Measurements of Frost Penetration
- 2020
-
Ingår i: Journal of Earth Sciences and Geotechnical Engineering. - : Scientific Press International Limited. - 1792-9040 .- 1792-9660. ; 10:5, s. 161-194
-
Tidskriftsartikel (refereegranskat)abstract
- Even though extensive pre-grouting is carried out during the construction of tunnels, certain leakages and drips remain. These remaining leakages are remedied by a combination of post-injection and drainage measures with, for example, frost insulated drain mats, whose function is to prevent the cold tunnel air from reaching a leakage spot and causing water to freeze. Despite these measures, some water may still enter the tunnels and cause problems during winter with ice formations and frost shattering. Icicles, ice pillars and ice-covered roads and railway tracks require constant maintenance. If ice occurs in the fracture network close to the tunnel contour or in the interface between the rock and shotcrete, it can cause degradation of the load-bearing capacity of the tunnel and fall-outs of both materials. In tunnel sections with water leakage problems it is common to protect the load-bearing structure from freezing with insulated drainage systems. To determine where along the tunnel efforts must be made to prevent ice formation, the temperature conditions of tunnels must be investigated. This article presents parts of the results from field measurements in two Swedish railway tunnels. The measurements involves monitoring of air and rock temperatures, air pressure and air velocity.
|
|
| 6. |
- Botelho, Anneliese H., et al.
(författare)
-
Effects of parallel fractures near a free surface on velocity amplification of S-wave
- 2017
-
Ingår i: Proceedings of the Ninth International Symposium on Rockbursts and Seismicity in Mines. - Santiago do Chile : University of Chile.
-
Konferensbidrag (refereegranskat)abstract
- When rock support is designed in a seismically active underground mine, it is important tochoose the right ejection velocity and calculate corresponding kinetic energy. Field monitoringand back-analyses have shown that ejection velocity of the order of 10 m/s and higher can resultfrom seismic events of moderate magnitude. Such velocities are much higher than those predictedusing peak particle velocity (PPV) obtained from scaling laws. Many researches have reportedthe amplification of particle velocity near excavation surface. Velocity amplification of P-wavetravelling through fractured rock near a free surface was recently studied. The amplification ofseismic waves on the skin of excavation is of interest in case of large seismic events. Seismic eventswith large magnitude are often associated with slip along weaknesses or shear fracturing of intactrock, which according to observations radiate much stronger S-wave as compared to P-wave.In this paper, velocity amplification of S-wave was investigated by modelling the dynamicinteraction between fractured rock and a free surface using a 2D discontinuum-based numericalprogram, UDEC (Universal Distinct Element Code). A 1D model with a fractured zone wasused to represent the fractured rock in this investigation. It is found that the shear stress ratio,wave frequency, fracture stifness, fracture spacing and thickness of fractured zone afect thevelocity amplification, in which the shear stress ratio is the most crucial factor influencing wavetransmission. The results have proved that the interaction of the seismic wave and multiplefractures near the free surface strongly influences the ground motion.
|
|
| 7. |
- Botelho, Anneliese H., et al.
(författare)
-
Velocity amplification of obliquely incident s-wave through fractures near free-surface
- 2019
-
Ingår i: Rock Mechanics for Natural Resources and Infrastructure Development - Full Papers. - : Taylor & Francis. ; , s. 1487-1494
-
Konferensbidrag (refereegranskat)abstract
- The rockfall risk due to mining-induced seismicity reduces by installing appropriate rock support to absorb the kinetic energy from a seismic event, which is calculated by assuming the mass of ejected rock and its ejection velocity. Estimation of ejection velocity is normally based on scaling laws that do not consider the effect of the excavation free-surface and existing fractures near the excavation free-surface. Field monitoring studies have shown that the peak particle velocity on the free-surface can be much larger than the velocity in deep solid rock. The interaction between the fractures and the free-surface under incident S-wave is investigated by using a two-dimensional UDEC model with fractured zone characterized as one, two, three and four sets of parallel fractures with varied intersecting angles. The results show that wave amplification factor varies according to the incident wave angle, the number of fracture sets and fracture spacing.
|
|
| 8. |
- Idris, Musa Adebayo, et al.
(författare)
-
Probabilistic-Based Stope Design Methodology for Complex Ore Body with Rock Mass Property Variability
- 2019
-
Ingår i: Journal of mining science. - Russia : Springer. - 1062-7391 .- 1573-8736. ; 55:5, s. 743-750
-
Tidskriftsartikel (refereegranskat)abstract
- This paper presents a probabilistic approach for optimizing stope design methodology whiletaking into consideration the variability in the rock mass properties. For this study, a complex orebody in aCanadian mine was used. Because of the variability in the rock mass properties of the orebody, it was notpossible to determine precisely, the values of geotechnical design input parameters and hence the need toutilize a probabilistic approach. Point Estimate Method (PEM), a probabilistic tool, was incorporated intonumerical analysis using FLAC3D to study the deformation magnitudes of various stope geometries todetermine the optimal stope geometry with a minimum ground control problem. Results obtained for thedistribution of the wall deformations and the floor heaves for each option of the stope geometry werecompared to select the best geometry to achieve the optimum stability condition. The methodologypresented in this study can be helpful in the process of underground mine planning and optimization incomplex orebody.
|
|
| 9. |
- Idris, Musa Adebayo, et al.
(författare)
-
ВЕРОЯТНОСТНАЯ МЕТОДИКА ПРОЕКТИРОВАНИЯ ОЧИСТНЫХ ЗАБОЕВ ДЛЯ СЛОЖНЫХ РУДНЫХ ТЕЛ С ИЗМЕНЯЮЩИМИСЯ СВОЙСТВАМИ ПОРОДНОГО МАССИВА
- 2019
-
Ingår i: Физико-технические проблемы разработки полезных ископаемых. - : Издательство СО РАН. - 0015-3273. ; :5, s. 56-62
-
Tidskriftsartikel (refereegranskat)abstract
- Представлен вероятностный подход для оптимизации методики расчета параметров забоя с учетом изменчивости свойств горного массива на примере сложного рудного месторождения в Канаде. Для точного определения значений входящих геотехнических параметров использован вероятностный метод PEM (метод точечной оценки) в совокупности с численным анализом и программным обеспечением FLAC3D. Определены деформации выработок с различной геометрией и оптимальные параметры выработки для минимизации проблем управления состоянием массива. Полученные результаты по распределению деформаций стенок и почвы выработок анализировались для каждого варианта с целью выбора их наилучшей геометрии и достижения оптимальной устойчивости
|
|
| 10. |
- Jones, Tristan, et al.
(författare)
-
Mining-Induced Deformation in the Malmberget Mine
- 2019
-
Ingår i: Rock Mechanics and Rock Engineering. - : Springer. - 0723-2632 .- 1434-453X. ; 52:6, s. 1903-1916
-
Tidskriftsartikel (refereegranskat)abstract
- The Norra Alliansen orebody of the Malmberget sublevel caving mine consists of iron ore interspersed with biotite schist and granitic inclusions. The schist is squeezed between the ore and the host rock and in direct contact with the ore along the majority of the length of the footwall. The schist exhibits high deformation when exposed to stress. SMART cable bolt roof deformation measurements are re-analyzed to draw conclusions regarding the patterns of deformation in the mine. Each bolt’s head is placed at the origin of a spherical coordinate system and the radius and inclination angle between the bolt and every production blast occurring during the bolt’s recorded lifetime are calculated. The deformation experienced by each instrument is investigated by comparing the long-term recorded movements with the developed geometric variables. Patterns of deformation magnitude and rate are found with respect to production-blast distance and inclination angle, instrument location, rock quality designation, and likely mining-induced stresses. Results show that deformation magnitude tends to be higher when driven by production blasting occurring on the production level above the instrumentation when accounting for the effects of distance, but average deformation magnitude for very-near production blasts tends to be higher than that for production blasts occurring directly above the instrument. Correlations also exist between the measured RQD, estimated rockmass parameters, and the measured deformation. Empirical evidence allows the identification of six scenarios which account for 91% of the recorded high-deformation-rate events. These scenarios help determine which production activities are most likely to cause high deformation rates.
|
|
