| 1. |
- Akter, Shaheda T.
(författare)
-
Experimental characterization and numerical modeling of compression perpendicular to the grain in wood and cross-laminated timber
- 2022
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Compression perpendicular to the grain (CPG) of wood is a typical loading situation in timber structures. It has been an extensively studied research topic for decades, due to the highly ductile behavior of wood under such loading, the large variations in mechanical properties, and the relevance of these properties in structural design. Among others, the main influencing factors for CPG properties are stressed volume, load and support configurations, and annual ring orientations to the loading direction. After the innovation of the massive, engineered wood based product, cross-laminated timber (CLT) and its application in high rise buildings, CPG of wood has gained further importance. The development of a non-homogeneous, undesired and combined stress state under CPG in solid wood, due to the material anisotropy in the radial-tangential plane, can build up a complex multi-axial stress state in CLT. As a comparatively new product, the study of the influencing factors for CPG properties of CLT, and an understanding of the local material behavior under such loading, is essential for product characterization and for the development of design guidelines to ensure safe and efficient design.The main aim of the doctoral thesis is to establish a relationship betweenthe anisotropic behavior of clear wood in the transverse plane and the structural response of CLT under CPG loading. Both experimental and numerical studies were adopted herein, to enhance the understanding of the basic material behavior and the product and structural behavior. On the clear wood scale, the focus was on developing a test setup for uniaxial and biaxial loading in the radial-tangential(RT) plane. The potential of the developed test setup for the biaxial testing in the transverse plane was exploited for the investigation of the moisture and time dependent behavior of clear wood under radial compression and rolling shear loading. For data acquisition, in addition to the force and displacement data measured by the internal actuators of the testing machine and an external load cell,a contact-free digital image correlation (DIC) system was used in the experimental investigations. A numerical model was developed, which can describe the elasto-plastic behavior of wood under compression in the transverse plane and predict the structural behavior of solid wood and CLT. For that purpose, a novel Quadratic multi-surface (QMS) failure criterion and a simplified Hoffman failure criterion were implemented in a user-subroutine in the finite element software Abaqus®, and their suitability was compared with the Abaqus implemented Hill’s criterion.The validation of the material models was based on the experimental investigations of failure behavior of clear wood under stress perpendicular to the grain with rolling shear interaction. The material models were further utilized to predict the structural response of solid wood and CLT wall-to-floor connections under CPG loading. The predicted response of CLT connections under CPG by using the above-mentioned material models was compared with experiments, which investigated the influences of different connection types, wall and floor thicknesses, positions of walls, and outer deck layer orientations. The models were then applied to investigate the influence of the pith location in the boards, the number of layers and the thickness of walls and the floor on the stiffness and strength of CLT connections. Moreover, the CLT connection’s rotational rigidity as a consequence of compressive force from the upper floor in a multi-story building was studied by means of finite element calculations.The DIC measured strain fields from the experiments on clear wood confirmed the dependence of strain field on the curvature of the annual rings. As regards the material models, Hill’s model resulted in significantly higher force carrying capacity than experiments on clear wood, whereas Hoffman’s and QMS models predicted reasonably well the force-displacement relationships as found in experiments. The Hoffman’s and QMS models predicted stiffness was about 5–10% higher than corresponding experimental results on clear wood, and about 25% higher for CLT connections. The higher difference in the latter case is due to the difference in material properties of clear wood and structural timber, and the contact behavior between the structural members. The results from CLT wall-to-floor connections revealed a strong influence of loading and supporting configurations, wall thickness and pith locations on their stiffness and strength. A compressive loading on the CLT wall showed a positive effect on the rotational stiffness of CLT wall-to-floor connections, which considerably reduces the CLT floor mid-span deflection in comparison to a simply-supported floor.The thesis work contributes to an enhanced understanding of the anisotropic material behavior of wood in the RT-plane and of its effects on structural timber and CLT under CPG loading. The outcomes of the thesis are beneficial to the product design and standardization of CLT and can be applied in further product development and in optimized structural design.
|
|
| 2. |
|
|
| 3. |
- Briggert, Andreas, 1984-, et al.
(författare)
-
Evaluation of three dimensional fibre orientation in Norway spruce using a laboratory laser scanner
- 2016
-
Ingår i: WCTE 2016. - Vienna : Vienna University of Technology. - 9783903039001
-
Konferensbidrag (refereegranskat)abstract
- This paper addresses laser scanning and utilization of the tracheid effect for determination of local fibre orientation, which is decisive for strength and stiffness of timber. A newly developed laboratory laser scanner that can be used for high resolution and high precision scanning of wood surfaces is used for in-depth assessment of a single Norway spruce specimen that contains a knot. It is assumed that the specimen has a plane of symmetry, through the knot, and by splitting the specimen in two parts it is possible to determine fibre orientation on orthogonal planes. Hence, by relying on the assumption of symmetry, the fibre orientation in 3D space can also be determined. The results are used to evaluate the possibility of utilizing the tracheid effect for determination of the out-of-plane fibre angle of an investigated surface. Furthermore, the results are used for verification of a theoretical fibre orientation model that has often been used by researchers.
|
|
| 4. |
- Briggert, Andreas, 1984-
(författare)
-
Modelling and strength grading of structural timber and glulam lamellae on the basis of optical scanning and dynamic excitation
- 2020
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Machine strength grading of sawn timber is a sawmill process in which density, modulus of elasticity (MOE) and bending or tensile strength are predicted such that the timber can be assigned to strength classes. The predictions of these properties are performed using one or several so-called indicating properties (IPs), which represent a board property, or combination of board properties, measured non-destructively. A limitation of today’s strength grading is that the IPs applied in the industry for prediction of strength, in general, are based on rather weak statistical relationships between IPs and strength properties, which in turn results in poor material utilisation. It is well known that the strength of sawn timber is associated with the presence of knots and their surrounding fibre disorientations. Local fibre direction at surfaces of softwood can be determined by means of the light scattering that occur when a wood surface is illuminated by a dot-laser, i.e. by application of the so-called tracheid effect. Lately, IPs based on such measurements have been developed, and some of the suggested IPs have a strong statistical relationship to bending strength. The purposes of the research presented in this thesis are to contribute with knowledge of possibilities and limitations of the tracheid effect and of data of fibre directions in the vicinity of knots, to evaluate if information of fibre directions at surfaces of Norway spruce sawn timber can be used to achieve a better material utilisation of glulam lamellae and finger-jointed timber, and to provide insight regarding the grading regulations in Europe. Results presented herein show that knots and fibre direction within the interior of boards can be modelled on the basis of data obtained by means of the tracheid effect, but also that a previously proposed method to determine out-of-plane fibre angles gives poor accuracy. As regards grading of glulam lamellae, an IP based on fibre directions and dynamic MOE is proposed for prediction of tensile strength. The latter is used when grading glulam lamellae. Application of the proposed IP resulted in substantially increased yield in strength classes. It is also shown that this IP is applicable for boards with sawn as well as with planed surface finish. Regarding current regulations for machine strength grading in Europe, results indicate that grading based on global board properties give higher yield than what is appropriate.
|
|
| 5. |
- Briggert, Andreas, 1984-, et al.
(författare)
-
Prediction of tensile strength of sawn timber : models for calculation of yield in strength classes
- 2020
-
Ingår i: Materials and Structures. - : Springer. - 1359-5997 .- 1871-6873. ; 53:3, s. 1-15
-
Tidskriftsartikel (refereegranskat)abstract
- In Europe, strength classes for structural timber and glulam lamellae are defined by minimum requirements of characteristic values of the grade determining properties (GDPs). To fulfill these minimum requirements of characteristic values in the daily production at sawmills, indicating properties (IPs) to GDPs are calculated for each board and based on predetermined limits of the IPs (settings) boards are assigned to the graded class, or rejected. The aims of this paper is to address and discuss two different grading procedures/models that can be applied when settings for IPs that reflects a local board property are derived and to show how the yield in different T-classes depend on the model applied. It is not always that a board’s weakest cross-section is evaluated in a destructive test. An IP representing a local board property can therefore be determined either as the lowest property of the tested part of the board or as the lowest property along the whole board when applied to derive settings. Results presented in this paper show that too low settings and too large yields are obtained when the latter IP is employed. Similarly, IPs reflecting a global board property, like axial dynamic MOE, also give too low settings and too high yield in strength classes. This paper is the second and closing part of a series of two paper on prediction of GDPs and procedures for grading sawn timber into T-classes.
|
|
| 6. |
- Briggert, Andreas, 1984-, et al.
(författare)
-
Prediction of tensile strength of sawn timber : definitions and performance of indicating properties based on surface laser scanning and dynamic excitation
- 2020
-
Ingår i: Materials and Structures. - : Springer. - 1359-5997 .- 1871-6873. ; 53:3, s. 1-20
-
Tidskriftsartikel (refereegranskat)abstract
- The presence of wood irregularities such as knots are decisive for the mechanical properties of sawn timber, and efficient utilisation of timber requires methods by which grade determining properties can be predicted with high accuracy. In the glulam and sawmilling industries today, there is a potential and a need for more accurate prediction methods. This paper concerns the performance of a set of indicating properties calculated by means of data from surface laser scanning, dynamic excitation and X-ray scanning, the latter used to obtain boards’ average density. A total number of 967 boards of Norway spruce originating from Finland, Norway and Sweden were used to determine statistical relationships between the indicating properties and the grade determining properties used to grade sawn timber into T-classes. Results show that the indicating properties give coefficients of determination to tensile strength as high as 0.70. Furthermore, results also show that laser scanning of boards with sawn surface finish give basis for almost as accurate grading as what scanning of planed boards do. The results imply that more accurate grading of timber into T-classes is possible by application of a new set of indicating properties. This paper is part one of a series of two papers. In the second paper, two models to derive settings and calculate yield in different strength classes using the indicating properties presented herein are compared and discussed.
|
|
| 7. |
- Briggert, Andreas, 1984-, et al.
(författare)
-
Three dimensional knot models based on surface laser scanning
- 2015
-
Ingår i: Proceedings 19th International Nondestructive Testing and Evaluation of Wood Symposium Rio de Janeiro, Brazil, 23-25 September, 2015.. - Madison, USA : USDA, Forest Service, Forest Products Laboratory. ; , s. 83-90, s. 83-90
-
Konferensbidrag (refereegranskat)abstract
- Most machine strength grading methods of today result in limited grading accuracy and poor yield in higher strength classes. A new and more accurate grading method utilizing laser scanning technique to determine the in-plane fibre directions on board surfaces was recently approved for the European market. In this, however, no consideration is taken to the out-of-plane direction of the fibres. A first step towards scanning-based 3D models of the fibre orientation is the establishment of 3D knot models. In this investigation laser scanning was used to identify knot surfaces on longitudinal board surfaces. By means of developed algorithms knot surfaces that belonged to the same physical knot visible on different sides of the board were identified. All knots with surface areas larger than 100 mm2 were correctly identified and modeled in 3D. This is a promising starting point for further development of the new grading method based on laser scanning.
|
|
| 8. |
- Briggert, Andreas, 1984-, et al.
(författare)
-
Tracheid effect scanning and evaluation of in-plane and out-of-plane fibre direction in Norway spruce using
- 2018
-
Ingår i: Wood and Fiber Science. - : Society of Wood Science and Technology. - 0735-6161. ; 50:4, s. 411-429
-
Tidskriftsartikel (refereegranskat)abstract
- Local fiber direction is decisive for both strength and stiffness in timber. In-plane fiber direction on surfaces of timber can be determined using the so-called tracheid effect which is frequently used in both research and industry applications. However, a similar established method does not exist for measuring the out-of-plane angle, also known as diving angle. The purposes of this article were to evaluate if the tracheid effect can also be used to determine, with reasonable accuracy, the out-of-plane angle in Norway spruce and to verify an existing mathematical model used to calculate the fiber direction in the vicinity of knots. A newly developed laboratory laser scanner was applied for assessment of fiber directions in a single Norway spruce specimen containing a knot. It was assumed that the specimen had a plane of symmetry through the center of the knot, and by splitting the specimen through this plane into two parts, it was possible to make measurements on orthogonal planes. The results showed that the out-of-plane angle could not be determined with very high accuracy and the difficulties related to this objective were analyzed. Regarding the mathematical model of fiber direction in the vicinity of a knot, fiber directions calculated on the basis of this model agreed well with experimentally obtained fiber directions, but successful application of the model requires that the geometry of the knot is known in detail.
|
|
| 9. |
- Habite, Tadios, 1990-, et al.
(författare)
-
Automatic detection of pith location along boards of Norway spruce on the basis of data from optical scanning of longitudinal surfaces
- 2019
-
Ingår i: CompWood 2019 - International Conference on Computational Methods in Wood Mechanics - from material properties to Timber Structures, Växjö, Sweden, June 17-19, 2019. - Växjö : Lnu Press. - 9789188898647 ; , s. 64-64
-
Konferensbidrag (refereegranskat)abstract
- Different mechanical and physical properties of wood are related to the location of pith. Norway spruce wood from the centre of logs, close to the pith, is characterized by lower longitudinal MOE, larger spiral grain angle, and larger longitudinal shrinkage coefficient than what wood farther away from the pith is [1]. Thus, knowledge of pith location along timber boards may play an important role in both appearance grading and in assessment of mechanical properties such as strength [2]. The current work aims to develop an algorithm which is capable of automatically estimating the pith location of Norway spruce boards, along the boards’ length direction, by utilizing optical scanning of longitudinal surfaces. The initial step of the algorithm is to identify defect free sections along the timber board. This is done by utilizing data from tracheid effect scanning of the four sides of the timber board. Thereafter, a continuous wavelet transform (CWT), similar to fast Fourier transform, is applied on grey scale images from scanning, to analyse the variation of light intensity across the four surfaces at selected positions along the board. Obtained local frequencies correspond to the local annular ring pattern on surfaces. Then, assuming that annular growth rings are concentric circles with the pith in the centre, detected local annular ring wavelengths (using CWT) and artificial annual ring wavelengths corresponding to different hypothetical locations of pith are compared, and an optimization procedure is used to identify the location of pith that minimizes the discrepancy between the detected and artificial sets of annular ring wavelengths. Figure 1 shows grey scale images of short segments of longitudinal surfaces, graphs of the detected local annual ring widths, and a photograph of the board cross section where the determined location of pith is marked out. Preliminary results reveal that data from optical scanners and the suggested method allow for accurate detection of annular ring width and location of pith along boards.
|
|
| 10. |
- Habite, Tadios, et al.
(författare)
-
Automatic detection of pith location along norway spruce timber boards on the basis of optical scanning
- 2020
-
Ingår i: European Journal of Wood and Wood Products. - : Springer. - 0018-3768 .- 1436-736X. ; 78, s. 1061-1074
-
Tidskriftsartikel (refereegranskat)abstract
- Knowledge of annual ring width and location of pith in relation to board cross-sections, and how these properties vary in the longitudinal direction of boards, is relevant for many purposes, such as assessment of shape mechanical properties and stability of sawn timber. Hence, the present research aims at developing a novel method and an algorithm, based on data obtained from optical surface scanning, by which the pith location along the length of sawn timber boards can be determined accurately and automatically. The first step of the method is to identify clear wood sections, free of defects along boards. Then time-frequency analysis, using the continuous wavelet transform, is applied to detect the surface annual ring width distribution of the four sides of the selected sections. Finally, the pith location is estimated by comparing annual ring width distributions on the different surfaces, and assuming that annual rings are concentric circles with the pith in the centre. The proposed algorithm was applied to a total sample of 104 Norway spruce boards. Results indicate that optical scanners and the suggested automatic method allow for accurate detection of annual ring width and location of pith along boards. For a sample of boards with the pith located within the cross-section, a mean error of 2.6 mm and 3.2 mm in the depth and thickness direction, respectively, was obtained. For a sample of boards of which 60% with pith located outside the cross-section, a mean discrepancy between automatically and manually determined pith locations of 3.9 mm and 5.8 mm in depth and thickness direction, respectively, was obtained.
|
|
