| 1. |
- Zhang, Pimin, 1990-, et al.
(författare)
-
Effects of surface finish on the initial oxidation of HVAF-sprayed NiCoCrAlY coatings
- 2019
-
Ingår i: Surface & Coatings Technology. - Elsevier : Elsevier BV. - 0257-8972 .- 1879-3347. ; 364, s. 43-56
-
Tidskriftsartikel (refereegranskat)abstract
- Oxide scale formed on HVAF-sprayed NiCoCrAlY coatings and the effect of surface treatment were investigated by a multi-approach study combining photo-stimulated luminescence, microstructural observation and mass gain. The initial oxidationbehaviour of as-sprayed, polished and shot-peened coatings at 1000 °C is studied. Both polished and shot-peened coatings exhibited superior performance due to rapid formation of α-Al2O3 fully covering the coating and suppressing the growth of transient alumina, assisted by a high density of α-Al2O3 nuclei on surface treatment induced defects. Moreover, the fast development of a two-layer alumina scale consisting of an inward-grown inner α-Al2O3 layer and an outer layer transformed from outward-grown transient alumina resulted in a higher oxide growth rate of the as-sprayed coating.
|
|
| 2. |
- Zhang, Pimin, 1990-, et al.
(författare)
-
Isothermal oxidation behavior of HVAF-sprayed NiCoCrAlY coatings : Effect of surface treatment
- 2017
-
Ingår i: Proceedings of the International Thermal Spray Conference & Exposition (ITSC 2017). - New York : Curran Associates, Inc. - 9781510858220 ; , s. 456-461
-
Konferensbidrag (refereegranskat)abstract
- NiCoCrAlY coatings are widely used as bond coats for ceramic thermal barrier coatings (TBCs) andoxidation and corrosion protective overlay coatings in industrial gas turbines. High temperature oxidation behaviour of NiCoCrAlYs has a great influence on the coating performance and lifetime of TBCs. A promising route to decrease the oxidation rate of such coatings is post-coating surface modification which can facilitate formation of a uniform alumina scale with a considerably slower growth rate compared to the as-sprayed coatings. In this work, the effect of surface treatment by means of shot peening and laser surface melting (LSM) on the oxidation resistance of high velocity air-fuel (HVAF) sprayed NiCoCrAlY coatings was studied. Isothermal oxidation was carried out at 1000⁰C for 1000h. Results showed that the rough surface of as-sprayed HVAF sprayed coatings was significantly changed after shot peening and LSM treatment, with a compact and smooth appearance. After the exposure, the oxide scales formed on surface-treated NiCoCrAlY coatings showed different morphology and growth rate compared to those formed on as-sprayed coating surface. The oxidation behaviour of surface treated HVAF-sprayed NiCoCrAlY coatings were revealed and discussed.
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
- Almer, J., et al.
(författare)
-
Strain and texture analysis of coatings using high-energy x-rays
- 2003
-
Ingår i: Journal of Applied Physics. - : AIP Publishing. - 0021-8979 .- 1089-7550. ; 94:1, s. 697-702
-
Tidskriftsartikel (refereegranskat)abstract
- We investigate the internal strain and crystallographic orientation (texture) in physical-vapor deposited metal nitride coatings of TiN and CrN. A high-energy diffraction technique is presented that uses synchrotron x rays and an area detector, and which allows the strain and intensity distributions of multiple crystallographic planes to be measured by a single x-ray exposure. Unique texture states and nonlinear sin2 strain distributions are observed for all coatings investigated. Quantitative analysis indicates that existing micromechanical models can reasonably predict strain and corresponding stress for mixed-hkl reflections but are inadequate for fully describing measured data. Alternative mechanisms involving deposition-induced defects are proposed
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
|
|
| 9. |
|
|
| 10. |
- Chen, Zhe, 1987-, et al.
(författare)
-
Effect of Machining Parameters on Cutting Force and Surface Integrity when High-Speed Turning AD730™ with PCBN Tools
- 2019
-
Ingår i: The International Journal of Advanced Manufacturing Technology. - : Springer London. - 0268-3768 .- 1433-3015. ; 100:9-12, s. 2601-2615
-
Tidskriftsartikel (refereegranskat)abstract
- The novel wrought nickel-based superalloy, AD 730™, is a good candidate material for turbine disc applications at high temperatures beyond 650 °C. The present study focuses on the machining performance of this newly developed alloy under high-speed turning conditions with advanced PCBN tools. Meanwhile, the machined surface integrity as influenced by cutting speed and feed rate was also investigated. The surface integrity was thoroughly characterized in terms of surface roughness and morphology, machining-induced plastic deformation, white layer formation, and residual stresses. It has been found that the cutting speed and feed rate had a strong effect on the cutting forces and resultant surface integrity. The cutting forces required when machining the alloy were gradually reduced with increasing cutting speed, while at 250 m/min and above, the flank tool wear became stronger which led to increased thrust force and feed force. A higher feed rate, on the other hand, always resulted in higher cutting forces. Increasing the cutting speed and feed rate in general deteriorated the surface integrity. High cutting speeds within the range of 200–250 m/min and a low feed rate of 0.1 mm/rev are preferable in order to implement more cost-effective machining without largely reducing the surface quality achieved. The formation of tensile residual stresses on the machined AD 730™, however, could be of a concern where good fatigue resistance is critical.
|
|
