| 1. |
|
|
| 2. |
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
- Boman, Christoffer, et al.
(författare)
-
Evaluation of a constant volume sampling setup for residential biomass fired appliances : Influence of dilution conditions on particulate and PAH emissions
- 2005
-
Ingår i: Biomass and Bioenergy. - : Elsevier BV. - 0961-9534 .- 1873-2909. ; 29:4, s. 258-268
-
Tidskriftsartikel (refereegranskat)abstract
- Increased concerns about particulate matter (PM) and polycyclic aromatic hydrocarbons (PAH) emissions from residential biomass combustion and their potential health effects, motivates detailed emission measurements under controlled conditions. Traditional sampling in raw flue gases can suffer from drawbacks mainly related to transient flows and the condensable nature of organic compounds. Whole flow dilution with constant volume sampling (CVS) is an alternative method but different sampling conditions may, however, influence the emission characteristics. The objective was to design a CVS system for emission measurements in residential biomass fired appliances and determine the influence of dilution sampling conditions on the characteristics and distributions of PM and PAH. Softwood pellets were combusted in a pellet stove with variations in; dilution ratio (3-7x), sampling temperature (45-75°C), dilution tunnel residence time (2-4 s) and fuel load (2.3 and 4.8 kW) according to a statistical experimental design. The sampling conditions did not influence either the emission concentrations of PM, CO and NO or the particle size distribution. Variations in residence time had no significant effect on any studied emission parameter. However, increased concentrations of organic gaseous carbon (OGC) and PAH were observed with increased dilution ratio. The distribution between particulate and semivolatile phase was influenced for 12 of the 37 analyzed PAH compounds, mainly by increased fractions of semivolatile material at higher sampling temperature. No influence of sampling temperature was observed for the concentrations of PAHtot or the dominating PAH compounds, i.e. phenanthrene, fluoranthene and pyrene. The results together with practical considerations also suggest sampling at 50±5°C and 3-4 times dilution as robust and applicable conditions in the presently designed setup. © 2005 Elsevier Ltd. All rights reserved.
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
|
|
| 9. |
|
|
| 10. |
- Boman, Christoffer, et al.
(författare)
-
Stove performance and emission characteristics in residential wood log and pellet combustion : Part 1: Pellet stoves
- 2011
-
Ingår i: Energy & Fuels. - : American Chemical Society (ACS). - 0887-0624 .- 1520-5029. ; 25:1, s. 307-314
-
Tidskriftsartikel (refereegranskat)abstract
- Stove performance, characteristics and quantities of gaseous and particulate emissions were determined for two different pellet stoves, varying fuel load, pellet diameter and chimney draught. This approach aimed at covering variations in emissions from stoves in use today. The extensive measurement campaign included CO, NOx, organic gaseous carbon, volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs), total particulate matter (PMtot) as well as particle mass and number concentrations, size distributions and inorganic composition. At high load, most emissions were similar. For stove B, operating at high residual oxygen and solely with primary air, the emissions of PMtot and particle numbers were higher while the particles were smaller. Lowering the fuel load, the emissions of CO and hydrocarbons increased dramatically for stove A, which operated continuously also at lower fuel loads. On the other hand for stove B, which had intermittent operation at lower fuel loads, the emissions of hydrocarbons increased only slightly lowering the fuel load, while CO emissions increased sharply, due to high emissions at the end of the combustion cycle. Beside methane, dominating VOCs were ethene, acetylene and benzene and the emissions of VOC varied in the range 1.1-47 mg/MJfuel. PAH emissions (2-340 µg/MJfuel) were generally dominated by phenantrene, fluoranthene and pyrene. PMtot (15-45 mg/MJfuel) were in all cases dominated by fine particles with mass median diameters in the range 100-200 nm, peak mobility diameters of 50-85 nm and number concentrations in the range 4×1013- 3×1014 particles/MJfuel. During high load conditions the particulate matter was totally dominated by inorganic particles at 15-25 mg/MJfuel consisting of potassium, sodium, sulfur and chlorine, in the form of K2SO4, K3Na(SO4)2 and KCl. The study shows that differences in operation and modulation principles for the tested pellet stoves, relevant for appliances in use today, will affect the performance and emissions significantly, although with lower scattering in the present study compared to compiled literature data.
|
|
