| 1. |
- Aad, G., et al.
(författare)
-
The ATLAS Inner Detector commissioning and calibration
- 2010
-
Ingår i: European Physical Journal C. Particles and Fields. - : Springer Science and Business Media LLC. - 1434-6044 .- 1434-6052. ; 70:3, s. 787-821
-
Tidskriftsartikel (refereegranskat)abstract
- The ATLAS Inner Detector is a composite tracking system consisting of silicon pixels, silicon strips and straw tubes in a 2 T magnetic field. Its installation was completed in August 2008 and the detector took part in data-taking with single LHC beams and cosmic rays. The initial detector operation, hardware commissioning and in-situ calibrations are described. Tracking performance has been measured with 7.6 million cosmic-ray events, collected using a tracking trigger and reconstructed with modular pattern-recognition and fitting software. The intrinsic hit efficiency and tracking trigger efficiencies are close to 100%. Lorentz angle measurements for both electrons and holes, specific energy-loss calibration and transition radiation turn-on measurements have been performed. Different alignment techniques have been used to reconstruct the detector geometry. After the initial alignment, a transverse impact parameter resolution of 22.1 +/- 0.9 mu m and a relative momentum resolution sigma (p) /p=(4.83 +/- 0.16)x10(-4) GeV(-1)xp (T) have been measured for high momentum tracks.
|
|
| 2. |
- Abate, E., et al.
(författare)
-
Combined performance tests before installation of the ATLAS Semiconductor and Transition Radiation Tracking Detectors
- 2008
-
Ingår i: Journal of Instrumentation. - 1748-0221. ; 3
-
Tidskriftsartikel (refereegranskat)abstract
- The ATLAS (A Toroidal LHC ApparatuS) Inner Detector provides charged particle tracking in the centre of the ATLAS experiment at the Large Hadron Collider (LHC). The Inner Detector consists of three subdetectors: the Pixel Detector, the Semiconductor Tracker (SCT), and the Transition Radiation Tracker (TRT). This paper summarizes the tests that were carried out at the final stage of SCT+TRT integration prior to their installation in ATLAS. The combined operation and performance of the SCT and TRT barrel and endcap detectors was investigated through a series of noise tests, and by recording the tracks of cosmic rays. This was a crucial test of hardware and software of the combined tracker detector systems. The results of noise and cross-talk tests on the SCT and TRT in their final assembled configuration, using final readout and supply hardware and software, are reported. The reconstruction and analysis of the recorded cosmic tracks allowed testing of the offline analysis chain and verification of basic tracker performance parameters, such as efficiency and spatial resolution, in combined operation before installation.
|
|
| 3. |
- Abdesselam, A., et al.
(författare)
-
Engineering for the ATLAS SemiConductor Tracker (SCT) end-cap
- 2008
-
Ingår i: Journal of Instrumentation. - 1748-0221. ; 3
-
Tidskriftsartikel (refereegranskat)abstract
- The ATLAS SemiConductor Tracker (SCT) is a silicon-strip tracking detector which forms part of the ATLAS inner detector. The SCT is designed to track charged particles produced in proton-proton collisions at the Large Hadron Collider (LHC) at CERN at an energy of 14 TeV. The tracker is made up of a central barrel and two identical end-caps. The barrel contains 2112 silicon modules, while each end-cap contains 988 modules. The overall tracking performance depends not only on the intrinsic measurement precision of the modules but also on the characteristics of the whole assembly, in particular, the stability and the total material budget. This paper describes the engineering design and construction of the SCT end-caps, which are required to support mechanically the silicon modules, supply services to them and provide a suitable environment within the inner detector. Critical engineering choices are highlighted and innovative solutions are presented - these will be of interest to other builders of large-scale tracking detectors. The SCT end-caps will be fully connected at the start of 2008. Further commissioning will continue, to be ready for proton-proton collision data in 2008.
|
|
| 4. |
- Abdesselam, A., et al.
(författare)
-
The barrel modules of the ATLAS semiconductor tracker
- 2006
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 568:2, s. 642-671
-
Tidskriftsartikel (refereegranskat)abstract
- This paper describes the silicon microstrip modules in the barrel section of the SemiConductor Tracker (SCT) of the ATLAS experiment at the CERN Large Hadron Collider (LHC). The module requirements, components and assembly techniques are given, as well as first results of the module performance on the fully assembled barrels that make up the detector being installed in the ATLAS experiment.
|
|
| 5. |
- Aad, G., et al.
(författare)
-
- 2011
-
swepub:Mat__t (refereegranskat)
|
|
| 6. |
- Aad, G., et al.
(författare)
-
- 2011
-
Tidskriftsartikel (refereegranskat)
|
|
| 7. |
- Aad, G., et al.
(författare)
-
- 2012
-
swepub:Mat__t (refereegranskat)
|
|
| 8. |
- Aad, G., et al.
(författare)
-
- 2011
-
swepub:Mat__t (refereegranskat)
|
|
| 9. |
- Aad, G., et al.
(författare)
-
- 2013
-
swepub:Mat__t (refereegranskat)
|
|
| 10. |
- Aad, G., et al.
(författare)
-
- 2012
-
swepub:Mat__t (refereegranskat)
|
|
