| 1. |
- An, Siwen, et al.
(författare)
-
Signal-to-Noise Ratio Optimization in X-ray Fluorescence Spectrometry for Chromium Contamination Analysis
- 2021
-
Ingår i: Talanta. - : Elsevier BV. - 0039-9140 .- 1873-3573. ; 230
-
Tidskriftsartikel (refereegranskat)abstract
- In most cases, direct X-ray fluorescence (XRF) analysis of solutions entails technical difficulties due to a high X-ray scattering background resulting in a spectrum with a poor signal-to-noise ratio (SNR). Key factors that determine the sensitivity of the method are the energy resolution of the detector and the amount of scattered radiation in the energy range of interest. Limiting the width of the primary spectrum by the use of secondary targets, or filters, can greatly improve the sensitivity for specific portions of the spectrum. This paper demonstrates a potential method for SNR optimization in direct XRF analysis of chromium (Cr) contamination. The suggested method requires minimal sample preparation and achieves higher sensitivity compared to existing direct XRF analysis. Two states of samples, fly ash and leachate from municipal solid waste incineration, were investigated. The effects of filter material, its absorption edge and filter thickness were analyzed using the combination of Monte Carlo N-Particle (MCNP) code and energy-dispersive XRF spectrometry. The applied filter removes primary photons with energies interfering with fluorescence photons from the element of interest, thus results in lower background scattering in the spectrum. The SNR of Cr peak increases with filter thickness and reaches a saturation value when further increased thickness only increases the measurement time. Measurements and simulations show that a Cu filter with a thickness between 100 μm and 140 μm is optimal for detecting Cr by taking into account both the SNR and the exposure time. With direct XRF analysis for solutions, the limit of quantitation (LOQ) of the achieved system was 0.32 mg/L for Cr, which is well below the allowed standard limitation for landfills in Sweden. This work shows that XRF can gain enough sensitivity for direct monitoring to certify that the Cr content in leachate is below environmental limits.
|
|
| 2. |
- Correa, J., et al.
(författare)
-
Characterisation of a PERCIVAL monolithic active pixel prototype using synchrotron radiation
- 2016
-
Ingår i: Journal of Instrumentation. - : IOP. - 1748-0221 .- 1748-0221. ; 11:2
-
Tidskriftsartikel (refereegranskat)abstract
- PERCIVAL ("Pixelated Energy Resolving CMOS Imager, Versatile And Large") is a monolithic active pixel sensor (MAPS) based on CMOS technology. Is being developed by DESY, RAL/STFC, Elettra, DLS, and PAL to address the various requirements of detectors at synchrotron radiation sources and Free Electron Lasers (FELs) in the soft X-ray regime. These requirements include high frame rates and FELs base-rate compatibility, large dynamic range, single-photon counting capability with low probability of false positives, high quantum efficiency (QE), and (multi-)megapixel arrangements with good spatial resolution. Small-scale back-side-illuminated (BSI) prototype systems are undergoing detailed testing with X-rays and optical photons, in preparation of submission of a larger sensor. A first BSI processed prototype was tested in 2014 and a preliminary result—first detection of 350eV photons with some pixel types of PERCIVAL—reported at this meeting a year ago. Subsequent more detailed analysis revealed a very low QE and pointed to contamination as a possible cause. In the past year, BSI-processed chips on two more wafers were tested and their response to soft X-ray evaluated. We report here the improved charge collection efficiency (CCE) of different PERCIVAL pixel types for 400eV soft X-rays together with Airy patterns, response to a flat field, and noise performance for such a newly BSI-processed prototype sensor.
|
|
| 3. |
- Fröjdh, Christer, 1952-, et al.
(författare)
-
Precision scan-imaging for paperboard quality inspection utilizing X-ray fluorescence
- 2018
-
Ingår i: Journal of Instrumentation. - : Institute of Physics Publishing. - 1748-0221 .- 1748-0221. ; 13:1
-
Tidskriftsartikel (refereegranskat)abstract
- Paperboard is typically made up of a core of cellulose fibers [C6H10O5] and a coating layer of [CaCO3]. The uniformity of these layers is a critical parameter for the printing quality. Current quality control methods include chemistry based visual inspection methods as well as X-ray based methods to measure the coating thickness. In this work we combine the X-ray fluorescence signals from the Ca atoms (3.7 keV) in the coating and from a Cu target (8.0 keV) placed behind the paper to simultaneously measure both the coating and the fibers. Cu was selected as the target material since its fluorescence signal is well separated from the Ca signal while its fluorescence's still are absorbed sufficiently in the paper. A laboratory scale setup is built using stepper motors, a silicon drift detector based spectrometer and a collimated X-ray beam. The spectroscopic image is retrieved by scanning the paperboard surface and registering the fluorescence signals from Ca and Cu. The exposure time for this type of setups can be significantly improved by implementing spectroscopic imaging sensors. The material contents in the layers can then be retrieved from the absolute and relative intensities of these two signals.
|
|
| 4. |
- Fröjdh, Christer, et al.
(författare)
-
Spectral resolution in pixel detectors with single photon processing
- 2013
-
Ingår i: Proceedings SPIE Optical Engineering + Applications, 2013. - : SPIE - International Society for Optical Engineering. - 9780819497024
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Pixel detectors based on photon counting or single photon processing readout are becoming popular for spectral X-ray imaging. The detector is based on deep submicron electronics with functions to determine the energy of each individual photon in every pixel. The system is virtually noiseless when it comes to the number of the detected photons. However noise and variations in system parameters affect the determination of the photon energy. Several factors affect the energy resolution in the system. In the readout electronics the most important factors are the threshold dispersion, the gain variation and the electronic noise. In the sensor contributions come from charge sharing, variations in the charge collection efficiency, leakage current and the statistical nature of the charge generation, as described by the Fano factor. The MEDIPIX technology offers a powerful tool for investigating these effects since energy spectra can be captured in each pixel. In addition the TIMEPIX chip, when operated in Time over Threshold mode, offers an opportunity to analyze individual photon interactions, thus addressing charge sharing and fluorescence. Effects of charge sharing and the properties of charge summing can be investigated using MEDIPIX3RX. Experiments are performed using both Si and CdTe detectors. In this paper we discuss the various contributions to the spectral noise and how they affect detector response. The statements are supported with experimental data from MEDIPIX-type detectors.
|
|
| 5. |
- Marras, A., et al.
(författare)
-
Experimental characterization of the PERCIVAL soft X-ray detector
- 2016
-
Ingår i: 2015 IEEE Nuclear Science Symposium and Medical Imaging Conference, NSS/MIC 2015. - : Institute of Electrical and Electronics Engineers (IEEE). - 9781467398626
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Considerable interest has been manifested for the use of high-brilliance X-ray synchrotron sources and X-ray Free-Electron Lasers for the investigation of samples.
|
|
| 6. |
- Niskanen, Ilpo, et al.
(författare)
-
Determination of nanoparticle size using Rayleigh approximation and Mie theory
- 2019
-
Ingår i: Chemical Engineering Science. - : Elsevier. - 0009-2509 .- 1873-4405. ; 201, s. 222-229
-
Tidskriftsartikel (refereegranskat)abstract
- Accurate determination of the size of nanoparticles has an important role in many different scientific and industrial purposes, such as in material, medical and environment sciences, colloidal chemistry and astrophysics. We describe an effective optical method to determine the size of nanoparticles by analysis of transmission and scattering of visible spectral range data from a designed UV-Vis multi-spectrophotometer. The size of the nanoparticles was calculated from the extinction cross section of the particles using Rayleigh approximation and Mie theory. We validated the method using polystyrene nanospheres, cellulose nanofibrils, and cellulose nanocrystals. A good agreement was achieved through graphical analysis between measured extinction cross section values and theoretical Rayleigh approximation and Mie theory predictions for the sizes of polystyrene nanospheres at wavelength range 450-750 nm. Provided that Rayleigh approximation's forward scattering (FS)/back scattering (BS) ratio was smaller than 1.3 and Mie theory's FS/BS ratio was smaller than 1.8. A good fit for the hydrodynamic diameter of nanocellulose was achieved using the Mie theory and Rayleigh approximation. However, due to the high aspect ratio of nanocellulose, the obtained results do not directly reflect the actual cross-sectional diameters of the nanocellulose. Overall, the method is a fast, relatively easy, and simple technique to determine the size of a particle by a spectrophotometer. Consequently, the method can be utilized for example in production and quality control purposes as well as for research and development applications.
|
|
| 7. |
- Norlin, Börje, et al.
(författare)
-
Readout cross-talk for alpha-particle measurements in a pixelated sensor system
- 2015
-
Ingår i: Journal of Instrumentation. - : IOP. - 1748-0221 .- 1748-0221. ; 10
-
Tidskriftsartikel (refereegranskat)abstract
- Simulations in Medici are performed to quantify crosstalk and charge sharing in a hybrid pixelated silicon detector. Crosstalk and charge sharing degrades the spatial and spectral resolution of single photon processing X-ray imaging systems. For typical medical X-ray imaging applications, the process is dominated by charge sharing between the pixels in the sensor. For heavier particles each impact generates a large amount of charge and the simulation seems to over predict the charge collection efficiency. This indicates that some type of non modelled degradation of the charge transport efficiency exists, like the plasma effect where the plasma might shield the generated charges from the electric field and hence distorts the charge transport process. Based on the simulations it can be reasoned that saturation of the amplifiers in the Timepix system might generate crosstalk that increases the charge spread measured from ion impact on the sensor.
|
|
| 8. |
- Norlin, Börje, 1967-, et al.
(författare)
-
X-ray fluorescence measurements of toxic metal content in ash from municipal solid waste incineration
- 2017
-
Ingår i: 2016 IEEE Nuclear Science Symposium, Medical Imaging Conference and Room-Temperature Semiconductor Detector Workshop (NSS/MIC/RTSD). - : IEEE. - 9781509016426
-
Konferensbidrag (refereegranskat)abstract
- The vision of this paper is development of an online X-ray fluorescence method for monitoring of metal content in ash from municipal solid waste (MSW) incineration. With such measurements directly on site it is possible to optimize an ash washing process in incineration plants, allowing the fly ash to be stored in a landfill for non-hazardous waste. The presented X-ray fluorescence measurement assures that the measurement accuracy is sufficient for metal content monitoring. The actual measurement process is also fast enough to be possible to implement as an online measurement method. The optimal measurement setup is different for different metals. Several different metals might need environmental monitoring, which metals might vary over time due to systematic variations in waist content. Detection of a wide range of metals will require an X-ray source with variable voltage and multiple detectors.
|
|
| 9. |
- Olsen, Martin, 1971-, et al.
(författare)
-
Schottky model for triboelectric temperature dependence
- 2018
-
Ingår i: Scientific Reports. - : Springer Science and Business Media LLC. - 2045-2322. ; 8:1
-
Tidskriftsartikel (refereegranskat)abstract
- The triboelectric effect, charging by contact, is the working principle in a device called a triboelectric nanogenerator. They are used as efficient energy transducers in energy harvesting. In such generators the charging of surfaces at contact is followed by a separation of the surfaces increasing the electrical energy which can subsequently be used. Different materials have different triboelectric potentials leading to charging at contact. The temperature dependence of the charging has just recently been studied: the triboelectric effect is decreasing with temperature for a generator of Al-PTFE-Cu. Here, we suggest a mechanism to explain this effect assuming ion transfer using a two-level Schottky model where the two levels corresponds to the two surfaces. The difference in binding energy for ions on the two surfaces then enters the formula for charging. We fit the triboelectric power density as a function of temperature obtained from a two-level Schottky model to measured data for nanogenerators made of Al-PTFE-Cu found in three references. We obtain an average separation energy corresponding to a temperature of 365 K which is of the right magnitude for physically adsorbed atoms. We anticipate that this model could be used for many types of triboelectric nanogenerators.
|
|
| 10. |
|
|
