| 1. |
- Aamodt, K., et al.
(författare)
-
The ALICE experiment at the CERN LHC
- 2008
-
Ingår i: Journal of Instrumentation. - 1748-0221. ; 3:S08002
-
Forskningsöversikt (refereegranskat)abstract
- ALICE (A Large Ion Collider Experiment) is a general-purpose, heavy-ion detector at the CERN LHC which focuses on QCD, the strong-interaction sector of the Standard Model. It is designed to address the physics of strongly interacting matter and the quark-gluon plasma at extreme values of energy density and temperature in nucleus-nucleus collisions. Besides running with Pb ions, the physics programme includes collisions with lighter ions, lower energy running and dedicated proton-nucleus runs. ALICE will also take data with proton beams at the top LHC energy to collect reference data for the heavy-ion programme and to address several QCD topics for which ALICE is complementary to the other LHC detectors. The ALICE detector has been built by a collaboration including currently over 1000 physicists and engineers from 105 Institutes in 30 countries, Its overall dimensions are 16 x 16 x 26 m(3) with a total weight of approximately 10 000 t. The experiment consists of 18 different detector systems each with its own specific technology choice and design constraints, driven both by the physics requirements and the experimental conditions expected at LHC. The most stringent design constraint is to cope with the extreme particle multiplicity anticipated in central Pb-Pb collisions. The different subsystems were optimized to provide high-momentum resolution as well as excellent Particle Identification (PID) over a broad range in momentum, up to the highest multiplicities predicted for LHC. This will allow for comprehensive studies of hadrons, electrons, muons, and photons produced in the collision of heavy nuclei. Most detector systems are scheduled to be installed and ready for data taking by mid-2008 when the LHC is scheduled to start operation, with the exception of parts of the Photon Spectrometer (PHOS), Transition Radiation Detector (TRD) and Electro Magnetic Calorimeter (EMCal). These detectors will be completed for the high-luminosity ion run expected in 2010. This paper describes in detail the detector components as installed for the first data taking in the summer of 2008.
|
|
| 2. |
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
|
|
| 9. |
- Dahlman-Hoglund, A., et al.
(författare)
-
Endotoxin in Aerosol Particles from Metalworking Fluids Measured with a Sioutas Cascade Impactor
- 2022
-
Ingår i: Annals of Work Exposures and Health. - : Oxford University Press (OUP). - 2398-7308 .- 2398-7316. ; 66:2, s. 260-268
-
Tidskriftsartikel (refereegranskat)abstract
- Objectives The aim of this study was to characterize personal occupational exposure to endotoxin in size-separated airborne particles of MWF aerosol, using a Sioutas cascade impactor (SCI). Methods Exposure to inhalable fractions of MWF aerosol and endotoxin was measured by personal sampling of 52 individuals over an 8-h work shift using a PAS-6 sampler in parallel with a SCI (<0.25, 0.25-0.5, 0.5-1.0, 1.0-2.5, and 2.5-10 mu m). Aerosol mass concentration was measured for each worker with a real-time instrument (DataRAM) during a full shift. Samples of MWF were collected from the machines and central tanks during the work shift. Results A total of 117 measurements of inhalable MWF aerosols were made among 52 workers. The geometric mean of inhalable MWF aerosol was 0.16 mg m(-3) air. The geometric mean of endotoxin concentration on the inhalable sampler was 0.15 EU m(-3). Airborne endotoxin was found on all size fractions from the impactor, with the major part seen in the fraction (2.5-10 mu m). There was a correlation between the inhalable fraction of endotoxin measured by the PAS-6 sampler and on the SCI sampler (2.5-10 mu m), estimated to be 0.51 for all samples (P < 0.0001). The concentration of endotoxin varied between the MWFs, as did the proportion of Gram-negative bacteria among the culturable bacteria (>80% in one MWF and <1.5% in the other three). Conclusions The personal exposure to inhalable fractions of endotoxin contained in the MWF aerosol were low, where most of the endotoxin were found in fraction (2.5-10 mu m), measured by SCI. There are differences between factories and MWF systems regarding the distribution of endotoxin and so results from one context should not be generalized to other plants and systems. Compressed air was used for less than 10 min shift(-1). The mixed-effect model showed that working with open machines and grinding as cutting task were important determinants of exposure to inhalable aerosol. It is important to keep occupational exposure to aerosols low with the help of good ventilation systems, enclosed machines, and organization of work.
|
|
| 10. |
|
|
