| 1. |
- Akter, Shaheda T., et al.
(författare)
-
Numerical modelling of wood under combined loading of compressionperpendicular to the grain and rolling shear
- 2021
-
Ingår i: Engineering structures. - : Elsevier. - 0141-0296 .- 1873-7323. ; 244
-
Tidskriftsartikel (refereegranskat)abstract
- Numerical modeling is an efficient tool for experimental validation and for gaining a deeper understanding of complex material phenomena, especially when causal relationships are overlaid by material variability. Wood is such a highly orthotropic and complex material, which in engineering problems however is considered as macro- homogeneous. The aim of this study is to numerically investigate stress and strain states of wood in the radial- tangential plane and the influence of the orthotropic material behavior on the structural response. Model vali-dation is based on experiments performed on clear wood of Norway spruce (Picea abies) by using a biaxial test setup. Three material models were used, namely Hill’s plasticity model, the Hoffman criterion and a novel quadratic multi-surface (QMS) criterion. After validation on the local material scale, the models were applied to the engineering problem of compression perpendicular to the grain for studying the effect of the unloaded length. As a novel part, the influence of the annual ring structure on the local material behavior and the global elasto- plastic force–displacement behavior of wood under compression perpendicular to the grain were numerically investigated. Hill’s failure criterion was found to be the least suitable at both length scales, local material behavior and global structural response. The Hoffman and the QMS criteria showed quite good agreement with the biaxial experiments in terms of force–displacement relations and strain distributions for different loading situations, especially for combinations with radial compression, while there was less agreement with experiments for the behavior of combinations with tangential compression. Application of these material models to compression perpendicular to the grain for studying the unloaded length effect yielded similar trends as observed in structural tests. A reasonable and similar force–displacement response by Hoffman and QMS criteria was observed, while Hill’s model yielded significantly overestimated force carrying capacity. Differences in force-–displacement response for different loading situations were well in line with literature findings and the infl-ence of the annual ring curvature on the overall force–displacement behavior could be quantified.
|
|
| 2. |
- Akter, Shaheda T., et al.
(författare)
-
Stiffness of cross-laminated timber (CLT) wall-to-floor-to-wall connections in platform-type structures
- 2021
-
Ingår i: World Conference on Timber Engineering 2021, WCTE 2021. - Santiago, Chile : World Conference on Timber Engineering, WCTE.
-
Konferensbidrag (refereegranskat)abstract
- Wall-to-floor-to-wall connections are important for the performance of multi-storey, platform-type cross-laminated timber (CLT) structures. Their stiffness properties are studied by means of a numerical model, which was previously validated with experimental data from material testing and CLT connections loaded perpendicular to the grain. In this work, the stiffness of CLT wall-to-floor-to-wall connections is derived and its dependence on the compressive loading in the CLT walls and on wall and floor thicknesses were investigated. The compatibility of the local model with the connection size in structural design models, was investigated by studying the effect of the floor length and the wall height in the numerical model. The results showed that both rotational elastic stiffness and moment capacity of the floor connection increase with increasing compressive force on the CLT wall. However, a moderate decrease in stiffness, but a stronger rotation hardening was found for higher wall pressures, while lower wall pressures yielded an ideal plastic behaviour. The wall thickness showed a higher influence on the connection stiffness and moment capacity than the floor thickness. The influence of the support condition on the deflection of a CLT floor was exemplified. This study includes novel stiffness data for the design of CLT floors in platform type constructions.
|
|
| 3. |
- Bader, Thomas K., 1980-, et al.
(författare)
-
Dowel deformations in multi-dowel LVL-connections under moment loading
- 2015
-
Ingår i: Wood Material Science & Engineering. - : Taylor & Francis. - 1748-0272 .- 1748-0280. ; 10:3, s. 216-231
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of the experimental study presented herein is the assessment and quantification of the behavior of individual dowels in multi-dowel connections loaded by a bending moment. For this purpose, double-shear, steel-to-timber connections with nine steel dowels arranged in different patterns and with different dowel diameters were tested in four-point bending. In order to achieve a ductile behavior with up to 7° relative rotation, the connections were partly reinforced with self-tapping screws. The reinforcement did not influence the global load–deformation behavior, neither for dowel diameters of 12 mm nor for 20 mm, as long as cracking was not decisive. The deformation of the individual dowels was studied by means of a non-contact deformation measurement system. Thus, the crushing deformation, that is, the deformation at the steel plate, and the bending deformation of the dowels could be quantified. In the case of 12 mm dowels, the bending deformation was larger than the crushing deformation, while it was smaller in the case of 20 mm dowels. Moreover, dowels loaded parallel to the grain showed larger bending deformations than dowels loaded perpendicular to the grain. This indicates that the loading of the individual dowels in the connection differs depending on their location.
|
|
| 4. |
- Bader, Thomas K., 1980-, et al.
(författare)
-
Experimental characterization of the global and local behavior of multi-dowel LVL-connections under complex loading
- 2016
-
Ingår i: Materials and Structures. - : Springer Science and Business Media LLC. - 1359-5997 .- 1871-6873. ; 49:6, s. 2407-2424
-
Tidskriftsartikel (refereegranskat)abstract
- The thorough experimental characterization of a dowel-type connection under various combinations of bending moments and normal forces is presented in this study. Double-shear steel-to-timber connections with 12 and 20 mm steel dowels were tested in a 4-point bending test set-up. The load, between the connected steel and wood beams, was transferred by the dowels themselves and also via an additional (passive) contact device, which introduced an eccentric normal force in the timber beam. The behavior of the connections was studied at the global scale of the connection and at the local scale of the individual dowels. A non-contact deformation measurement system was used to assess the changes of the location of the center of relative rotation over the entire loading. At the same time, the head deformations of the individual dowels could be measured, giving a direct indication about the force distribution among the dowels. Due to reinforcement, connections behaved distinctly ductile with a global relative rotation of up to 3°. Pre-stressing of the contact device by a force of 40 kN yielded an even stiffer behavior. For the particular configurations tested herein, the center of rotation was found to be close to the vertical axis of symmetry of the joint and close to the top row of the dowels. Moreover, the superimposed vertical shift of the center of relative rotation in case of a delayed normal force could be quantified. © 2015 RILEM
|
|
| 5. |
|
|
| 6. |
- Blumer, Samuel, et al.
(författare)
-
Moisture induced stresses and deformations in parquet floors : An experimental and numerical study
- 2009
-
Ingår i: Wood research. - Slovakia : State Forest Products Research Inst. - 1336-4561. ; 54:1, s. 89-101
-
Tidskriftsartikel (refereegranskat)abstract
- The indoor climate in buildings has changed in the last decade due to more efficient climatic systems, floor heating systems and larger open floor areas with more natural light. All this has induced increasing ranges of relative humidity between different seasons. Also with decreasing relative humidity (in the winter 30-50% RH, in the summer 70-90% RH), floor-heating systems increase the temperature in wooden parquet planks for example. Such variations can result in troublesome deformations, delamination of the surface layer and development of cracks in the parquet flooring boards. Sometimes there is only deterioration of the appearance but the durability of the flooring system can also be reduced. Many laboratory tests have to be done before reaching an optimal design of the parquet elements. Due to high coasts and time constraints of experiments, other supplementary research methods should be tested and evaluated. The articles' main objective was to increase understanding of the behaviour of parquet floors exposed to different climatic conditions using numerical calculation. The use of the finite element models provides options for design purposes of wood flooring systems. Several finite element models for adequate design have been created, tested and applied. After calibration and validation of the calculation method, parameter studies on the influence of material properties, geometry of the parquet floors and the long-term behaviour of the wood and glue line were performed. The results show a strong relation between material and geometry choice on the deformation, for example the gap opening and on the stress distribution in glue line, which can induce delamination of the surface layer and distortional effects of the parquet boards
|
|
| 7. |
- Blyberg, Louise, et al.
(författare)
-
Adhesive joints for structural timber/glass applications : Experimental testing and evaluation methods
- 2012
-
Ingår i: International Journal of Adhesion and Adhesives. - : Elsevier BV. - 0143-7496 .- 1879-0127. ; 35, s. 76-87
-
Tidskriftsartikel (refereegranskat)abstract
- A study of three different adhesives, silicone, acrylate and polyurethane, intended for adhesive joints in structural timber/glass applications is presented in this paper. Intentionally, adhesives with a wide range of properties were chosen. The adhesive bonds between timber and glass were tested both in tension and in shear with a bond area of 800 mm2. Special fixtures were designed both for gluing and testing the specimens. The results include strength and failure type of the adhesive bond as well as deformation of the bond lines, measured with LVDTs and a non-contact optical 3D-deformation measuring system used in combination with finite element modelling in order to obtain detailed information about the behaviour.Of the tested adhesives, the acrylate (SikaFast 5215) provided the largest strength, both in tension and shear. The mean strength obtained for this adhesive bond was 3.0 MPa in tension and 4.5 MPa in shear.Further, it is demonstrated how rotations in the specimen during the test can be detected with the optical measuring system and how finite element modelling can be used to study the stress distribution internally in the adhesive bond. One conclusion obtained from the combination of results from the optical measuring system and finite element modelling is that the behaviour of the silicone adhesive is highly influenced by its near incompressible behaviour.
|
|
| 8. |
- Dorn, Michael, 1978-, et al.
(författare)
-
Development of large-scale load-bearing timber-glass structural elements
- 2014
-
Ingår i: WCTE 2014 - World Conference on Timber Engineering.
-
Konferensbidrag (refereegranskat)abstract
- The building industry demands ever more effective structural elements with a multitude of requirements at the same time. There is increasing interest for load-bearing glass elements which can be deployed in timber structures, e.g. in the outer façade or as column or beam elements within the building. In an on-going research project, the materials glass, timber and the adhesive combining the former have to be selected to fit each other but also suit the application. The mechanical properties are studied individually as well as in combined small-scale specimens experimentally. Furthermore,large-scale tests on beams and shear walls are performed. This is accompanied by numerical analysis to study a wide range of dimensions and variations as well as specific design situations. The final output of the project will be prototypes to beused in showcase projects.
|
|
| 9. |
|
|
| 10. |
- Kandler, Georg, et al.
(författare)
-
Effective stiffness prediction of GLT beams based on stiffness distributions of individual lamellas
- 2015
-
Ingår i: Wood Science and Technology. - : Springer. - 0043-7719 .- 1432-5225. ; 49:6, s. 1101-1121
-
Tidskriftsartikel (refereegranskat)abstract
- The mechanical properties of structural timber-particularly in terms of stiffness and strength-are subject to high variability, which also affects the properties of timber products made from structural timber, e.g., glued laminated timber (GLT). In this paper, the influence of the longitudinal stiffness variability of wooden lamellas on the effective stiffness of GLT is investigated. In a first step, the local fiber orientation on the surfaces of 350 lamellas of Norway spruce was determined by an optical scanning device. This fiber angle information in combination with a micromechanical model for wood was used for the generation of a longitudinal stiffness profile of each lamella. Recording the position and orientation of each lamella, a total number of 50 GLT beams were assembled (with 4, 7, and 10 laminations) and tested under four-point bending. Knowing the stiffness profile of each board and its location within the GLT beam allowed for an accurate numerical finite element model, which is able to predict the effective GLT stiffness with high accuracy. Interesting insights into the relation between the stiffness of lamellas and the resulting GLT beams could be gained, and finally, a numerical simulation tool which is able to reproduce the experimental results appropriately was obtained.
|
|
