| 1. |
- Almroth, Per, 1975-, et al.
(author)
-
Modeling of the high temperature behaviour of IN792 in gas turbine hot parts
- 2002
-
In: Computational materials science. - 0927-0256 .- 1879-0801. ; 25:3, s. 305-315
-
Journal article (other academic/artistic)abstract
- The material parameters for two isothermal viscoplastic models with deliberately limited sets of material parameters have been estimated. The models are to describe the behaviour of the nickel based superalloy IN792 in a gas turbine hot part application. The models are based on a power law flow equation and the state variable used is backstress. The model calibration is done by least-squares optimization using non-standard constitutive tests that are aimed at describing relevant component conditions. The constitutive tests give information about the kinematic hardening effects for the backstress evolution equations, while secondary creep data provides stress versus inelastic strain rate information for the flow equation. All tests are uniaxial and isothermal. With the estimated parameter sets the models give relatively good fits to the data. The results suggest that the models can be used to describe the high temperature behaviour of IN792. ⌐ 2002 Elsevier Science B.V. All rights reserved.
|
|
| 2. |
- Andersson, Håkan, 1970-
(author)
-
A Co-Simulation Approach for Hydraulic Percussion Units
- 2018
-
Licentiate thesis (other academic/artistic)abstract
- This Licentiate of Engineering thesis concerns modelling and simulation of hydraulic percussion units. These units are often found in equipment for breaking or drilling in rock and concrete, and are also often driven by oil hydraulics, in which complex fluid-structure couplings are essential for their operation.Current methodologies used today when developing hydraulic percussion units are based on decoupled analyses, which are not correctly capturing the important coupled mechanisms. Hence, an efficient method for coupled simulations is of high importance, since these mechanisms are critical for the function of these units. Therefore, a co-simulation approach between a 1D system simulation model representing the fluid system and a structural 3D FE-model is proposed.This approach is presented in detail, implemented for two well-known simulation tools and evaluated for a simple but relevant model. The Hopsan simulation tool was used for the fluid system and the FE-simulation software LS-DYNA was used for the structural mechanics simulation. The co-simulation interface was implemented using the Functional Mock-up Interface-standard.The approach was further developed to also incorporate multiple components for coupled simulations. This was considered necessary when models for the real application are to be developed. The use of two components for co-simulation was successfully evaluated for two models, one using the simple rigid body representation, and a second where linear elastic representations of the structural material were implemented.An experimental validation of the co-simulation approach applied to an existing hydraulic hammer was performed. Experiments on the hydraulic hammer were performed using an in-house test rig, and responses were registered at four different running conditions. The co-simulation model was developed using the same approach as before. The corresponding running conditions were simulated and the responses were successfully validated against the experiments. A parameter study was also performed involving two design parameters with the objective to evaluate the effects of a parameter change.This thesis consists of two parts, where Part I gives an introduction to the application, the simulation method and the implementation, while Part II consists of three papers from this project.
|
|
| 3. |
- Andersson, Håkan, 1970-
(author)
-
A Co-Simulation Tool Applied to Hydraulic Percussion Units
- 2022
-
Doctoral thesis (other academic/artistic)abstract
- In this dissertation, a co-simulation tool is presented that is meant to comprise a more comprehensive environment for modelling and simulation of hydraulic percussion units, which are used in hydraulic hammers and rock drills. These units generates the large impact forces, which are needed to demolish concrete structures in the construction industry or to fragment rock when drilling blast holes in mine drifting. This type of machinery is driven by fluid power and is by that dependent of coupled fluid-structure mechanisms for their operation. This tool consists of a 1D fluid system model, a 3D structural mechanic model and an interface to establish the fluid-structure couplings, which has in this work been applied to a hydraulic hammer. This approach will enable virtual prototyping during product development with an ambition to reduce the need for testing of physical prototypes, but also to facilitate more detailed studies of internal mechanisms. The tool has been implemented for two well-known simulation tools, and a co-simulation interface to enable communication between them has been devel-oped. The fluid system is simulated using the Hopsan simulation tool and the structural parts are simulated using the FE-simulation software LS-DYNA. The implementation of the co-simulation interface is based on the Functional Mock-up Interface standard in Hopsan and on the User Defined Feature module in LS-DYNA. The basic functions of the tool were first verified for a simple but relevant model comprising co-simulation of one component, and secondly co-simulation of two components were verified. These models were based on rigid body and linear elastic representation of the structural components. Further, it was experimentally validated using an existing hydraulic hammer product, where the responses from the experiments were compared to the corresponding simulated responses. To investigate the effects from a parameter change, the hammer was operated and simulated at four different running conditions. Dynamic simulation of the sealing gap, which is a fundamental mechanism used for controlling the percussive motion, was implemented to further enhance the simulated responses of the percussion unit. This implementation is based on a parametrisation of the deformed FE-model, where the gap height and the eccentric position are estimated from the deformed geometry in the sealing gap region, and then the parameters are sent to the fluid simulation for a more accurate calculation of the leakage flow. Wear in percussion units is an undesirable type of damage, which may cause significant reduction in performance or complete break-down, and today there are no methodology available to evaluate such damages on virtual prototypes. A method to study wear was developed using the co-simulation tool to simulate the fundamental behaviour of the percussion unit, and the wear routines in LS-DYNA were utilised for the calculation of wear.
|
|
| 4. |
- Andersson, Håkan, 1970-, et al.
(author)
-
Simulation of wear in hydraulic percussion units using a co-simulation approach
- 2023
-
In: International Journal of Modelling and Simulation. - : Taylor & Francis. - 0228-6203 .- 1925-7082. ; 43:3, s. 265-281
-
Journal article (peer-reviewed)abstract
- In this study, a developed co-simulation method, which couples 1D-fluid and 3D-structural models, has been utilised to simulate wear in a hydraulic percussion unit. The effect of wear is generally detrimental on performance and lifetime for such units, but can also cause catastrophic failure and breakdown, requiring a total overhaul and replacement of core components. One experiment of standard straight impact was performed to investigate the tolerance against seizure. The percussion unit was operated at successively increasing operating pressures, and the level of wear was registered at each step, until seizure occurred. The co-simulation model was used to replicate the running conditions from the experiment to simulate the structural response to be used as input for the wear routine to calculate the wear depth. The wear pattern from the simulations corresponds well to the wear pattern from the experiment. Further, the effect of a misaligned impact on wear development was also studied, as this is a loading situation that typically occurs for hydraulic percussion units. The study demonstrates that the simulation method used has a potential for simulating wear and predicting seizure in hydraulic percussion units.
|
|
| 5. |
- Andersson, Håkan, 1970-, et al.
(author)
-
System level co-simulation of a control valve and hydraulic cylinder circuit in a hydraulic percussion unit
- 2017
-
In: Proceedings of 15:th Scandinavian International Conference on Fluid Power, June 7-9, 2017, Linköping, Sweden. - Linköping : Linköping University Electronic Press. - 9789176853696 ; , s. 225-235
-
Conference paper (peer-reviewed)abstract
- In this study a previously developed co-simulation method that is based on a 1D system model representing the fluid components of a hydraulic machinery, within which structural 3D Finite Element (FE) models can be incorporated for detailed simulation of specific sub-models or complete structural assemblies, is further developed. The fluid system model consists of ordinary differential equation sub-models that are computationally very inexpensive, but still represents the fluid dynamics very well. The co-simulation method has been shown to work very well for a simple model representing a hydraulic driven machinery. A more complex model was set up in this work, in which two cylinders in the hydraulic circuit were evaluated. Such type of models, including both the main piston and control valves, are necessary as they represent the real application to a further extent than the simple model, of only one cylinder. Two models have been developed and evaluated, from the simple rigid body representation of the structural mechanics model, to the more complex model using linear elastic representation. The 3D FE-model facilitates evaluation of displacements, stresses, and strains on a local level of the model. The results can be utilised for fatigue assessment, wear analysis and for predictions of noise radiation.
|
|
| 6. |
- Azeez, Ahmed, 1991-
(author)
-
High-Temperature Durability Prediction of Ferritic-Martensitic Steel
- 2023
-
Doctoral thesis (other academic/artistic)abstract
- Materials used for high-temperature steam turbine sections are generally subjected to harsh environments with temperatures up to 625 °C. The superior creep resistance of 9–12 % Cr ferritic-martensitic steels makes them desirable for those critical steam turbine components. Additionally, the demand for fast and frequent steam turbine start-ups, i.e. flexible operations, causes accelerated fatigue damage in critical locations, such as grooves and notches, at the high-temperature inner steam turbine casing. A durability assessment is necessary to understand the material behaviour under such high temperatures and repeated loading, and it is essential for life prediction. An accurate and less conservative fatigue life prediction approach is achieved by going past the crack initiation stage and allowing controlled growth of cracks within safe limits. Besides, beneficial load-temperature history effects, i.e. warm pre-stressing, must be utilised to enhance the fracture resistance to cracks. This dissertation presents the high-temperature durability assessment of FB2 steel, a 9-12 % Cr ferritic-martensitic steam turbine steel.Initially, isothermal low-cycle fatigue testing was performed on FB2 steel samples. A fatigue life model based on finite element strain range partitioning was utilised to predict fatigue life within the crack initiation phase. Two fatigue damage regimes were identified, i.e. plastic- and creep-dominated damage, and the transition between them depended on temperature and applied total strain. Cyclic deformation and stress relaxation behaviour were investigated to produce an elastic-plastic and creep material model that predicts the initial and mid-life cyclic behaviour of the FB2 steel.Furthermore, the thermomechanical fatigue crack growth behaviour of FB2 steel was studied. Crack closure behaviour was observed and accounted for numerically and experimentally, where crack growth rate curves collapsed into a single curve. Interestingly, the collapsed crack growth curves coincided with isothermal crack growth tests performed at the minimum temperature of the thermomechanical crack growth tests. In addition, hold times and changes in the minimum temperature of the thermomechanical fatigue cycle did not influence crack closure behaviour.Finally, warm pre-stressing effects were explored for FB2 steel. A numerical prediction model was produced to predict the increase in the apparent fracture toughness. Warm pre-stressing effects can benefit the turbine life by enhancing fracture resistance and allowing longer fatigue cracks to grow within safe limits.
|
|
| 7. |
- Azeez, Ahmed, 1991-
(author)
-
High-Temperature Fatigue in a Steam Turbine Steel : Modelling of Cyclic Deformation and Crack Closure
- 2021
-
Licentiate thesis (other academic/artistic)abstract
- Existing conventional thermal power plants are retrofitted for flexible operations to assist the transition toward more renewable energies. The deployment of many renewable energy power plants is necessary to achieve a clean environment with less pollution. However, the intermittent nature of renewable energies, due to weather changes, and the lack of efficient large energy storage systems put renewables at a disadvantage. Flexible operations of power plants imply fast and frequent start-ups. Thus, retrofitted power production plants can be utilised as an energy backup to satisfy the immediate demand during peak energy times or when renewable energies are suddenly limited. Large thermal power plants generally employ steam turbines with high inlet temperature and pressure steam conditions. Materials used for components at the high-temperature turbine sections are expected to withstand harsh environments. The use of 9-12 % Cr martensitic steels is desirable due to, among other things, their superior resistance to creep for temperatures up to 625 °C. Retrofitting for flexible operations put steam turbine components under high-temperature fatigue loading conditions different from how they were designed before. The flexible operations could lead to fatigue cracking at critical locations, such as grooves and notches at the inner steam turbine casing. Thus, fatigue behaviour understanding of steam turbine materials under such loading conditions is essential for components life prediction. Accurate and less conservative fatigue life prediction approach is necessary to extend the turbine components life, which reduces waste and provides economic benefits. This can be done by extending operations past crack initiation phase and allowing controlled propagation of cracks in the components. Within the 9-12 % Cr steel class, the martensitic steam turbine steel called FB2 is studied under high-temperature fatigue. This includes investigating high-temperature fatigue life behaviour, cyclic deformation behaviour, stress relaxation behaviour, and crack propagation behaviour along with crack closure behaviour. This was achieved by experimentally testing samples made from FB2 steel under isothermal low cycle fatigue, isothermal fatigue crack propagation, and thermomechanical fatigue crack propagation.
|
|
| 8. |
- Azeez, Ahmed, et al.
(author)
-
Low Cycle Fatigue Modelling of Steam Turbine Rotor Steel
- 2019
-
In: 9th International Conference Materials Structure & Micromechanics of Fracture (MSMF9). - : Elsevier. ; , s. 149-154, s. 149-154
-
Conference paper (peer-reviewed)abstract
- Materials in steam turbine rotors are subjected to cyclic loads at high temperature, causing cracks to initiate and grow. To allow for more flexible operation, accurate fatigue models for life prediction must not be overly conservative. In this study, fully reversed low cycle fatigue tests were performed on a turbine rotor steel called FB2. The tests were done isothermally, within temperature range of room temperature to 600 °C, under strain control with 0.8-1.2 % total strain range. Some tests included hold time to calibrate the short-time creep behaviour of the material. Different fatigue life models were constructed. The life curve in terms of stress amplitude was found unusable at 600 °C, while the life curve in terms of total strain or inelastic strain amplitudes displayed inconsistent behaviour at 500 °C. To construct better life model, the inelastic strain amplitudes were separated into plastic and creep components by modelling the deformation behaviour of the material, including creep. Based on strain range partitioning approach, the fatigue life depends on different damage mechanisms at different strain ranges. This allowed the formulation of life curves based on plasticity or creep domination, which showed creep domination at 600 °C, while at 500 °C, creep only dominates for higher strain range.
|
|
| 9. |
- Bergqvist, Göran, et al.
(author)
-
A finite element analysis of stress distribution in bone tissue surrounding uncoupled or splinted dental implants
- 2008
-
In: Clinical Implant Dentistry and Related Research. - : Wiley. - 1523-0899 .- 1708-8208. ; 10:1, s. 40-46
-
Journal article (peer-reviewed)abstract
- Background: Several studies on one-stage surgery in the treatment of the edentulous maxilla with implant-supported fixed prostheses have reported problems with removable provisional prostheses, which can load the implants in an uncontrollable manner during healing, and jeopardize healing. Immediate splinting of the implants with a fixed provisional prosthesis has been proposed to protect the bone-implant interface.Purpose: This study used the finite element method (FEM) to simulate stresses induced in bone tissue surrounding uncoupled and splinted implants in the maxilla because of bite force loading, and to determine whether the differences in these stress levels are related to differences in observed bone losses associated with the two healing methods.Materials and Methods: Stress levels in the maxilla were studied using the FEM program TRINITAS (Institute of Technology, Linköping University, Linköping, Sweden) in which all phases – preprocessing/modeling, equation solving, and postprocessing/evaluation – were simulated.Results: Stress levels in bone tissue surrounding splinted implants were markedly lower than stress levels surrounding uncoupled implants by a factor of nearly 9.Conclusion: From a mechanical viewpoint, FEM simulation supports the hypothesis that splinting reduces damage evolution in bone tissue, which agrees with clinical observations.
|
|
| 10. |
- Borg, Rikard, 1962-, et al.
(author)
-
Simulating DCB, ENF and MMB experiments using shell elements and a cohesive zone model
- 2004
-
In: Composites Science And Technology. - 0266-3538 .- 1879-1050. ; 64:2, s. 269-278
-
Journal article (peer-reviewed)abstract
- A delamination model for shell elements is presented. It consists of an adhesive penalty contact formulation for initially tying shells together and a cohesive zone model for degrading the adhesive forces. An adhesive contact used between shell elements has to account for the thickness offset, such that the rotational degrees of freedom in the shell elements are included in the algorithm. This is considered in the present contact model and the complete delamination model is implemented in the explicit Finite Element code LS-DYNA. By preventing delamination growth the delamination model can be turned into a tied contact. As such it is used in two FE-models, where plates are bonded together and subjected to various loads. The adhesive penalty contact performs well. The complete delamination is validated by simulating the Double Cantilever Beam, End-Notch Flexural and Mixed Mode Bending setups, and the results are shown to be in agreement with experimental data.
|
|
