| 1. |
|
|
| 2. |
|
|
| 3. |
- Gard Timmerfors, Jessica, et al.
(författare)
-
New drum-chipping technology for a more uniform size distribution of wood chips
- 2019
-
Ingår i: Holzforschung. - : De Gruyter. - 0018-3830 .- 1437-434X.
-
Tidskriftsartikel (refereegranskat)abstract
- Wood chips from a novel type of drum chipper were compared to wood chips from a conventional disc chipper in an evaluation based on demonstration-scale and industrial-scale machinery. The evaluation was performed as the wood chippers were used as production machines in a kraft pulp mill using softwood. The average bulk density of the wood chips from the disc chipper and the drum chipper was similar and within the range of 138-140 kg/m 3 . The size distribution of the wood chips was investigated using a conventional screening method, and by using an automatized image-analysis system based on laser scanning. The average length was set to be the same, but the wood chips from the drum chipper had a more uniform length. The average thickness was similar, but the drum chipper generated slightly more thinner wood chips. Compared to the disc chipper and using the screening method, the drum chipper generated a similar fraction of oversized and overthick wood chips, 51% more large accept chips, 11% more total accept chips, and 74% less pin chips and fines. Image analysis resulted in similar data. The results indicate that drum chippers warrant further attention as an alternative to conventional industrial-scale disc chippers. ©2019 Jessica Gard Timmerfors et al.
|
|
| 4. |
- Gard Timmerfors, Jessica, 1989-, et al.
(författare)
-
The impact of using different wood qualities and wood species on chips produced using a novel type of pilot drum chipper
- 2021
-
Ingår i: Nordic Pulp & Paper Research Journal. - : De Gruyter Open. - 0283-2631 .- 2000-0669. ; 36:2, s. 214-226
-
Tidskriftsartikel (refereegranskat)abstract
- Resource-efficient wood chipping for forest-industrial processes demands large fractions of accept chips and small fractions of small-sized material, such as pin chips and fines. In Kraft pulping, a narrow distribution of wood chip thickness is important for even impregnation and for making high-quality pulp. Using newly developed forest-industrial drum-chipping technology, the investigation covered wood of varying moisture content, frozen versus unfrozen wood, and the use of different wood species. Using conventional techniques for analyzing wood chip dimensions, fast-grown spruce wood with high moisture content gave 4.2 % pin chips and fines, which was less than half of the fractions obtained with spruce wood with lower moisture content. A comparison between frozen and unfrozen pine resulted in slightly thinner and shorter chips for the frozen wood, but in both cases accept yields of up to ∼85 % were achieved. A comparison of different tree species (aspen, birch, pine, and spruce) resulted in larger accept fractions (∼90 %) for the hardwood species, even though the average length of these wood chips was as low as 17 mm. The results provide a first indication of how basic wood log properties affect the yields of accept chips and small-sized material when using modern industrial drum-chipping technology.
|
|
| 5. |
|
|
| 6. |
- Timmerfors, Jessica Gard, et al.
(författare)
-
Evaluation of chipping and impregnation of Scots pine heartwood with sulfite cooking liquor
- 2020
-
Ingår i: SN Applied Sciences. - : Springer. - 2523-3963 .- 2523-3971. ; 2:12
-
Tidskriftsartikel (refereegranskat)abstract
- Heartwood and sapwood of Scots pine were procured and chipped using a newly developed pilot drum chipper, which for the heartwood resulted in a combined fraction of pin chips and fines of ~ 3%. Heartwood wood chips were processed using a set of 15 different reaction conditions that differed with respect to impregnation and cooking procedures. The result was evaluated with regard to absorption of impregnation liquid, pulp yield, fraction of reject, viscosity, kappa number, brightness, fiber properties, and chemical composition measured using two different techniques (compositional analysis using two-step hydrolysis with sulfuric acid and Py-GC/MS). The chemical analyses provided detailed information about how all main organic constituents of the wood, cellulose, hemicelluloses, and lignin, were affected by operational parameters. Inclusion of a pressurized (9 bar) impregnation step resulted in a more efficient cook, but the duration of the impregnation step (five minutes and four hours were compared) was not decisive for the outcome. Omission of the impregnation step or using low-pressure impregnation resulted in high fractions of reject, poor delignification, and, with a cooking time of two hours, no advantages with regard to fiber length and fraction of fines. The results indicate that the conditions used during impregnation, such as pressure, temperature, and acidity of impregnation liquid, warrant further attention in future studies.
|
|
