| 1. |
- Abel, I, et al.
(author)
-
Overview of the JET results with the ITER-like wall
- 2013
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Journal article (peer-reviewed)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 2. |
- Romanelli, F, et al.
(author)
-
Overview of the JET results
- 2011
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Journal article (peer-reviewed)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
| 3. |
- Fenn, Kaja, et al.
(author)
-
The provenance of Danubian loess
- 2022
-
In: Earth-Science Reviews. - : Elsevier. - 0012-8252 .- 1872-6828. ; 226, s. 103920-
-
Journal article (peer-reviewed)abstract
- With one of the largest watersheds in Europe, draining complex geological terrains within the Alps, Bohemian Massif, Carpathians, Dinarides, and the Balkan Mountains, the Danube River valley has long been linked to the formation of thick loess deposits, particularly within the Middle and Lower Danube basins. However, uncertainty over the provenance of loess-palaeosol sequences along the Danube impacts our understanding of sediment generation mechanisms and hinders interpretation of paleoenvironmental proxies preserved in loess. To date, most of the studies investigating loess provenance in Europe have not attempted a standardised characterisation and synthesis of loess deposits with potential source rocks. Further, despite clear links identified between loess and rivers in Asia and Europe, detrital zircons have not yet been used systematically to investigate the relationship between loess and the fluvial sediments of the Danube and its tributaries. Finally, in European loess research, provenance fingerprinting has often been conducted using indirect approaches or bulk sample geochemical analyses, which have been shown to have a limited application in well mixed sedimentary bodies such as loess.This provenance study of loess along the Danube River integrates existing zircon U-Pb ages and Hf datasets for loess, rivers, and bedrock, with new loess zircon U-Pb and Hf results from loess sequences in Croatia, Serbia and Bulgaria. The results show that all surrounding mountain belts (i.e. the Alps, Bohemian Massif, Carpathians, Dinarides Alps, and Balkan Mountains) contribute primary sediment to loess deposits in the Danube valley via its modern tributary network. Critically sedimentary sources remain relatively homogenous along the river, with no apparent major change in source with tributary confluence, further highlighting the role of fluvial transport in homogenising sediment prior to final aeolian deposition. Whilst some small site variations can be observed, they are likely explained by contributions restricted to very local rock outcrops. Moreover, geomorphological results support floodplain sediments as the proximal sediment source and suggest that short-distance aeolian transport dominates sediment delivery to loess sequences, challenging distant sources hypotheses such as major Saharan sources. The identification of sediment sourced from lower elevation regions such as the Bohemian Massif, Dinarides, and Balkans, which did not support ice-caps, suggests that the role of glacial action in silt-size sediment production has been previously exaggerated. Therefore, the glacial and desert loess division inadequately separates and describes sediment generation processes. This research supports and furthers previous work, which suggests “mountain sourced and transported by-rivers” as a more appropriate term for the particles forming loess, at least in the Danube basin.
|
|
| 4. |
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
|
|
| 9. |
|
|
| 10. |
|
|
