| 1. |
- Sandström, Robin, 1988-
(författare)
-
Innovations in nanomaterials for proton exchange membrane fuel cells
- 2019
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Hydrogen technologies are rapidly receiving increased attention as it offers a renewable energy alternative to the current petroleum-based fuel infrastructure, considering that continued large-scale use of such fossil fuels will lead to disastrous impacts on our environment. The proton exchange membrane fuel cell should play a significant role in a hydrogen economy since it enables convenient and direct conversion of hydrogen into electricity, thus allowing the use of hydrogen in applications particularly suited for the transportation industry. To fully realize this, multiple engineering challenges as well as development of advanced nanomaterials must however be addressed.In this thesis, we present discoveries of new innovative nanomaterials for proton exchange membrane fuel cells by targeting the entire membrane electrode assembly. Conceptually, we first propose new fabrication techniques of gas diffusion electrodes based on helical carbon nanofibers, where an enhanced three-phase boundary was noted in particular for hierarchical structures. The cathode catalyst, responsible for facilitating the sluggish oxygen reduction reaction, was further improved by the synthesis of platinum-based nanoparticles with an incorporated secondary metal (iron, yttrium and cobalt). Here, both solvothermal and high-temperature microwave syntheses were employed. Catalytic activities were improved compared to pure platinum and could be attributed to favorably shifted oxygen adsorption energies as a result of successful incorporation of the non-precious metal. As best exemplified by platinum-iron nanoparticles, the oxygen reduction reaction was highly sensitive to both metal composition and the type of crystal structure. Finally, a proton exchange membrane based on fluorine and sulfonic acid functionalized graphene oxide was prepared and tested in hydrogen fuel cell conditions, showing improvements such as lowered hydrogen permeation and better structural stability. Consequently, we have demonstrated that there is room for improvement of multiple components, suggesting that more powerful fuel cells can likely be anticipated in the future.
|
|
| 2. |
- Andersson, Samir, 1976-
(författare)
-
Supramolecular chemistry based on redox-active components and cucurbit[n]urils
- 2010
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- This thesis describes the host-guest chemistry between Cucurbit[7]uril (CB[7]) and CB[8] and a series of guests including bispyridinium cations, phenols and napthalenes. These guests are bound to ruthenium polypyridine complexes or ruthenium based water oxidation catalysts (WOCs). The investigations are based upon utilizing the covalently linked photosensitizer and the electronic effects and chemical processes are investigated.
|
|
| 3. |
- Bo, Xu
(författare)
-
Advanced Organic Hole Transport Materials for Solution-Processed Photovoltaic Devices
- 2015
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Solution-processable photovoltaic devices (PVs), such as perovskite solar cells (PSCs) and solid-state dye-sensitized solar cells (sDSCs) show great potential to replace the conventional silicon-based solar cells for achieving low-cost and large-area solar electrical energy generation in the near future, due to their easy manufacture and high efficiency. Organic hole transport materials (HTMs) play important roles in both PSCs and sDSCs, and thereby can well facilitate the hole separation and transportation, for obtaining high performance solar cells.The studies in this thesis aimed to develop advanced small-molecule organic HTMs with low-cost, high hole mobility and conductivity for the achievement of highly efficient, stable and reproducible sDSCs and PSCs. In order to achieve these objectives, two different strategies were utilized in this thesis: the development of new generation HTMs with simple synthetic routes and the introduction of cost-effective p-type dopants to control the charge transport properties of HTMs.In Chapter 1 and Chapter 2, a general introduction of the solution-processed sDSCs and PSCs, as well as the characterization methods that are used in this thesis were presented.In Chapter 3 and Chapter 4, a series of novel triphenylamine- and carbazole- based HTMs with different oxidation potential, hole mobility, conductivity and molecular size were designed and synthesized, and then systematically applied and investigated in sDSCs and PSCs.In Chapter 5, two low-cost and colorless p-type dopants AgTFSI and TeCA were introduced for the organic HTM-Spiro-OMeTAD, which can significantly increase the conductivity of the Spiro-OMeTAD films. The doping effects on the influence of sDSC and PSC device performances were also systematically investigated.
|
|
| 4. |
- Daniel, Quentin
(författare)
-
Water oxidation : From Molecular Systems to Functional Devices
- 2017
-
Konstnärligt arbete (övrigt vetenskapligt/konstnärligt)abstract
- The production of hydrogen gas, through the process of water splitting,is one of the most promising concepts for the production of clean andrenewable fuel.The introduction of this thesis provides a brief overview of fossil fuelsand the need for an energy transition towards clean and renewable energy.Hydrogen gas is presented as a possible candidate fuel with its productionthrough artificial photosynthesis, being described. However, the highlykinetically demanding key reaction of the process – the water oxidationreaction – requires the use of a catalyst. Hence, a short presentation of differentmolecular water oxidation catalysts previously synthesized is also provided.The second part of the thesis focuses on ruthenium-based molecularcatalysis for water oxidation. Firstly, the design and the catalytic performancefor a new series of catalysts are presented. Secondly, a further study onelectron paramagnetic resonance of a catalyst shows the coordination of awater molecule to a ruthenium centre to generate a 7-coordinated complex atRuIII state. Finally, in an electrochemical study, coupled with nuclear magneticresonance analysis, mass spectrometry and X-ray diffraction spectroscopy, wedemonstrate the ability of a complex to perform an in situ dimerization of twounits in order to generate an active catalyst.The final part of this thesis focuses on immobilisation of first rowtransition metal catalysts on the surface of electrodes for electrochemical wateroxidation. Initially, a copper complex was designed and anchored on a goldsurface electrode. Water oxidation performance was studied byelectrochemistry, while deactivation of the electrode was investigated throughX-ray photoelectron spectroscopy, revealing the loss of the copper complexfrom the electrode during the reaction. Finally, we re-investigated cobaltporphyrin complexes on the surface of the electrode. Against the backgroundof previous report, we show that the decomposition of cobalt porphyrin intocobalt oxide adsorbed on the surface is responsible for the catalytic activity.This result is discussed with regard to the detection limit of various spectroscopic methods.
|
|
| 5. |
- Duan, Lele, 1982-
(författare)
-
Artificial Water Splitting: Ruthenium Complexes for Water Oxidation
- 2011
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- This thesis concerns the development and study of Ru-based water oxidation catalysts (WOCs) which are the essential components for solar energy conversion to fuels. The first chapter gives a general introduction about the field of homogenous water oxidation catalysis, including the catalytic mechanisms and the catalytic activities of some selected WOCs as well as the concerns of catalyst design. The second chapter describes a family of mononuclear Ru complexes [Ru(pdc)L3] (H2pdc = 2,6-pyridinedicarboxylic acid; L = pyridyl ligands) towards water oxidation. The negatively charged pdc2− dramatically lowers the oxidation potentials of Ru complexes, accelerates the ligand exchange process and enhances the catalytic activity towards water oxidation. A Ru aqua species [Ru(pdc)L2(OH2)] was proposed as the real catalyst. The third chapter describes the analogues of [Ru(terpy)L3]2+ (terpy = 2,2′:6′,2′′-terpyridine). Through the structural tailor, the ligand effect on the electrochemical and catalytic properties of these Ru complexes was studied. Mechanistic studies suggested that these Ru-N6 complexes were pre-catalysts and the Ru-aqua species were the real WOCs. The forth chapter describes a family of fast WOCs [Ru(bda)L2] (H2bda = 2,2′-bipyridine-6,6′-dicarboxylic acid). Catalytic mechanisms were thoroughly investigated by electrochemical, kinetic and theoretical studies. The main contributions of this work to the field of water oxidation are (i) the recorded high reaction rate of 469 s−1; (ii) the involvement of seven-coordinate Ru species in the catalytic cycles; (iii) the O-O bond formation pathway via direct coupling of two Ru=O units and (iv) non-covalent effects boosting up the reaction rate. The fifth chapter is about visible light-driven water oxidation using a three component system including a WOC, a photosensitizer and a sacrificial electron acceptor. Light-driven water oxidation was successfully demonstrated using our Ru-based catalysts.
|
|
| 6. |
- Gabrielsson, Erik, 1984-
(författare)
-
Molecular Engineering of D-π-A Dyes for Dye-Sensitized Solar Cells
- 2014
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Dye-sensitized solar cells (DSSCs) present an interesting method for the conversion of sunlight into electricity. Unlike in other photovoltaic technologies, the difficult tasks of light absorption and charge transport are handled by two different materials in DSSCs. At the heart of the DSSC, molecular light absorbers (dyes) are responsible for converting light into current.In this thesis the design, synthesis and properties of new metal-free D-π-A dyes for dye-sensitized solar cells will be explored. The thesis is divided into six parts:Part one offers a general introduction to DSSCs, dye design and device characterization.Part two is an investigation of a series of donor substituted dyes where structural benefits are compared against electronic benefits.In part three a dye assembly consisting of a chromophore tethered to two electronically decoupled donors is described. The assembly, capable of intramolecular regeneration, is found to impede recombination.Part four explores a method for rapidly synthesizing new D-π-A dyes by dividing them into donor, linker and acceptor fragments that can be assembled in two simple steps. The method is applied to synthesize a series of linker varied dyes for cobalt based redox mediators that builds upon the experience from part two.Part five describes the synthesis of a bromoacrylic acid based dye and explores the photoisomerization of a few bromo- and cyanoacrylic acid based dyes.Finally, in part six the experiences from previous chapters are combined in the design and synthesis of a D-π-A dye bearing a new pyridinedicarboxylic acid acceptor and anchoring group.
|
|
| 7. |
- Hagberg, Daniel, 1977-
(författare)
-
Synthesis of Organic Chromophores for Dye Sensitized Solar Cells.
- 2009
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- This thesis deals with development and synthesis of organic chromophores for dye sensitized solar cells. The chromophores are divided into three components; donor, linker and acceptor. The development of efficient organic chromophores for dye sensitized solar cells starts off with one new organic chromophore, D5. This chromophore consists of a triphenylamine moiety as an electron donor, a conjugated linker with a thiophene moiety and cyanoacrylic acid as an electron acceptor and anchoring group. Alternating the donor, linker or acceptor moieties independently, would give us the tool to tune the HOMO and LUMO energy levels of the chromophores. The following parts of this thesis regard this development strategy. The contributions to the HOMO and LUMO energy levels were investigated when alternating the linker moiety. Unexpected effects of the solar cell performances when increasing the linker length were revealed, however. In addition, the effect of an alternative acceptor group, rhodanine-3-acetic acid, in combination with different linker lengths was investigated. The HOMO and LUMO energy level tuning was once again successful. Electron recombination from the semiconductor to the electrolyte is probably the cause of the poor efficiencies obtained for this series of dyes. Finally, the development of functionalized triphenylamine based donors and the contributions from different substituents to the HOMO and LUMO energy levels and as insulating layers were investigated. This strategy has so far been the most successful in terms of reaching high efficiencies in the solar cell. A top overall efficiency of 7.79 % was achieved.
|
|
| 8. |
- Ji, Fuxiang, 1991-, et al.
(författare)
-
Remarkable Thermochromism in the Double Perovskite Cs2NaFeCl6
- 2023
-
Ingår i: Advanced Optical Materials. - : Wiley-Blackwell. - 2162-7568 .- 2195-1071.
-
Tidskriftsartikel (refereegranskat)abstract
- Lead-free halide double perovskites (HDPs) have emerged as a new generation of thermochromic materials. However, further materials development and mechanistic understanding are required. Here, a highly stable HDP Cs2NaFeCl6 single crystal is synthesized, and its remarkable and fully reversible thermochromism with a wide color variation from light-yellow to black over a temperature range of 10 to 423 K is investigated. First-principles, density functional theory (DFT)-based calculations indicate that the thermochromism in Cs2NaFeCl6 is an effect of electron–phonon coupling. The temperature sensitivity of the bandgap in Cs2NaFeCl6 is up to 2.52 meVK−1 based on the Varshni equation, which is significantly higher than that of lead halide perovskites and many conventional group-IV, III–V semiconductors. Meanwhile, this material shows excellent environmental, thermal, and thermochromic cycle stability. This work provides valuable insights into HDPs' thermochromism and sheds new light on developing efficient thermochromic materials.
|
|
| 9. |
- Ji, Fuxiang, 1991-, et al.
(författare)
-
Remarkable Thermochromism in the Double Perovskite Cs2NaFeCl6
- 2024
-
Ingår i: Advanced Optical Materials. - : John Wiley & Sons. - 2162-7568 .- 2195-1071. ; 12:8
-
Tidskriftsartikel (refereegranskat)abstract
- Lead-free halide double perovskites (HDPs) have emerged as a new generation of thermochromic materials. However, further materials development and mechanistic understanding are required. Here, a highly stable HDP Cs2NaFeCl6 single crystal is synthesized, and its remarkable and fully reversible thermochromism with a wide color variation from light-yellow to black over a temperature range of 10 to 423 K is investigated. First-principles, density functional theory (DFT)-based calculations indicate that the thermochromism in Cs2NaFeCl6 is an effect of electron-phonon coupling. The temperature sensitivity of the bandgap in Cs2NaFeCl6 is up to 2.52 meVK(-1) based on the Varshni equation, which is significantly higher than that of lead halide perovskites and many conventional group-IV, III-V semiconductors. Meanwhile, this material shows excellent environmental, thermal, and thermochromic cycle stability. This work provides valuable insights into HDPs' thermochromism and sheds new light on developing efficient thermochromic materials.
|
|
| 10. |
- Karlsson, Karl Martin, 1981-
(författare)
-
Design, Synthesis and Properties of Organic Sensitizers for Dye Sensitized Solar Cells
- 2011
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- This thesis gives a detailed description of the design and synthesis of new organic sensitizers for Dye sensitized Solar Cells (DSCs). It is divided in 7 chapters, where the first gives an introduction to the field of DSCs and the synthesis of organic sensitizers. Chapters 2 to 6 deal with the work of the author, starting with the first publication and the other following in chronological order. The thesis is completed with some concluding remarks (chapter 7). The DSC is a fairly new solar cell concept, also known as the Grätzel cell, after its inventor Michael Grätzel. It uses a dye (sensitizer) to capture the incident light. The dye is chemically connected to a porous layer of a wide band-gap semiconductor. The separation of light absorption and charge separation is different from the conventional Si-based solar cells. Therefore, it does not require the very high purity materials necessary for the Si-solar cells. This opens up the possibility of easier manufacturing for future large scale production. Since the groundbreaking work reported in 1991, the interest within the field has grown rapidly. Large companies have taken up their own research and new companies have started with their focus on the DSC. So far the highest solar energy to electricity conversion efficiencies have reached ~12%. The sensitizers in this thesis are based on triphenylamine or phenoxazine as the electron donating part in the molecule. A conjugated linker allows the electrons to flow from the donor to the acceptor, which will enable the electrons to inject into the semiconductor once they are excited. Changing the structure by introducing substituents, extending the conjugation and exchanging parts of the molecule, will influence the performance of the solar cell. By analyzing the performance, one can evaluate the importance of each component in the structure and thereby gain more insight into the complex nature of the dye sensitized solar cell.
|
|
