| 1. |
- Chen, Zhe, et al.
(författare)
-
Nano-scale characterization of white layer in broached Inconel 718
- 2017
-
Ingår i: Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. - Amsterdam : Elsevier BV. - 0921-5093 .- 1873-4936. ; 684, s. 373-384
-
Tidskriftsartikel (refereegranskat)abstract
- The formation mechanism of white layers during broaching and their mechanical properties are not well investigated and understood to date. In the present study, multiple advanced characterization techniques with nano-scale resolution, including transmission electron microscopy (TEM), transmission Kikuchi diffraction (TKD), atom probe tomography (APT) as well as nano-indentation, have been used to systematically examine the microstructural evolution and corresponding mechanical properties of a surface white layer formed when broaching the nickel-based superalloy Inconel 718.TEM observations showed that the broached white layer consists of nano-sized grains, mostly in the range of 20–50 nm. The crystallographic texture detected by TKD further revealed that the refined microstructure is primarily caused by strong shear deformation. Co-located Al-rich and Nb-rich fine clusters have been identified by APT, which are most likely to be γ′ and γ′′ clusters in a form of co-precipitates, where the clusters showed elongated and aligned appearance associated with the severe shearing history. The microstructural characteristics and crystallography of the broached white layer suggest that it was essentially formed by adiabatic shear localization in which the dominant metallurgical process is rotational dynamic recrystallization based on mechanically-driven subgrain rotations. The grain refinement within the white layer led to an increase of the surface nano-hardness by 14% and a reduction in elastic modulus by nearly 10% compared to that of the bulk material. This is primarily due to the greatly increased volume fraction of grain boundaries, when the grain size was reduced down to the nanoscale.
|
|
| 2. |
- Eriksson, Johan, 1987, et al.
(författare)
-
An atom probe tomography study of the chemistry of radiation-induced dislocation loops in Zircaloy-2 exposed to boiling water reactor operation
- 2021
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115. ; 550
-
Tidskriftsartikel (refereegranskat)abstract
- This study is complementary to previous atom probe tomography (APT) studies of irradiation effects in the zirconium alloy Zircaloy-2. Using APT in voltage pulse mode, a difference in morphology was observed between clusters of Fe and Ni and clusters of Fe and Cr in Zircaloy-2 exposed to a high fast neutron fluence in a commercial boiling water reactor. The Fe–Ni clusters were disc-shaped with a diameter of 5–15 nm, whereas the Fe–Cr clusters were spheroidal with a diameter of approximately 5 nm. Both types of clusters appeared to be located at irradiation-induced -type dislocation loops aligned in layers normal to the -direction. The concentration of Fe was higher in the Fe–Cr clusters than in the Fe–Ni clusters. The dilute Fe–Ni clusters, which seem to be segregation of Fe and Ni inside the loops, had formed on all three families of first-order prismatic planes with some deviation from perfect -axis alignment. The Fe–Cr clusters might be very small precipitates with a nucleation associated with the loops.
|
|
| 3. |
- Eriksson, Johan, 1987, et al.
(författare)
-
Nanoscale chemistry of Zircaloy-2 exposed to three and nine annual cycles of boiling water reactor operation — an atom probe tomography study
- 2022
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115. ; 561
-
Tidskriftsartikel (refereegranskat)abstract
- Atom probe tomography was used in this work to study the metal close to the metal/oxide interface in the zirconium alloy Zircaloy-2 exposed to three and nine annual cycles of operation in a commercial boiling water reactor. The two exposure times correspond to before and after the onset of acceleration in corrosion, hydrogen pickup, and growth. The alloying elements Sn, Fe, Cr, and Ni were observed to be redistributed after exposure. After both three and nine cycles, clusters containing Fe and Cr and typically of a spheroidal shape with an approximate diameter of 5 nm were observed to be located in layers presumed to be layers of -loops. On average, the cluster number density was slightly higher after nine cycles, with larger and more Cr-rich clusters. However, there were large grain-to-grain variations, which were larger than the differences between the two exposure times. Ni was only occasionally observed in the clusters. Sn was observed to be slightly enriched in the Fe–Cr clusters, but the Sn concentration was higher between than inside the layers of clusters. After nine cycles, clusters of Sn were detected in regions that were depleted of Fe and Cr. Enrichment of Sn, Fe, and Ni at features that appeared to be -component loops was observed after nine cycles, whereas no such features were observed after three cycles. Enrichment of Sn and Fe, and small amounts of Cr and Ni, was observed at grain boundaries after both exposure times. After three cycles, a partially dissolved second phase particle of Zr(Fe,Cr)2 type that contained about ten times more Cr than Fe was observed.
|
|
| 4. |
- Eriksson, Johan, 1987, et al.
(författare)
-
Solute Concentrations in the Matrix of Zirconium Alloys Studied by Atom Probe Tomography
- 2023
-
Ingår i: ASTM Special Technical Publication. - 0066-0558. ; STP1645, s. 149-172
-
Konferensbidrag (refereegranskat)abstract
- This work indicates that the matrix content of the alloying elements iron, chromium, and nickel in as-produced commercial Zircaloy-2-type materials is lower than what has been indicated by many previous studies. Atom probe tomography in voltage pulse mode was used to study the matrix content of solutes in Zircaloy-2 of type LK3/L and a similar model alloy, called Alloy 2, of the same heat treatment. Both alloys were analyzed in the as-produced state and after reactor exposure. In the as-produced materials, the concentrations of iron, chromium, and nickel were all below the detection limits of around 10 wt. ppm. After reactor exposure, these alloying elements were observed to reside in clusters at loops, and the matrix content (including clusters) of iron had increased to about 1,200 wt. ppm in the fueled region of the rod and to about half that value in the plenum region. The chromium content in the fueled region was approximately 100 wt. ppm, and the nickel content was approximately 200 wt. ppm. In the plenum region, the content of these elements was lower. However, due to an uneven distribution of clusters, there was a wide scatter in the measured concentrations in the irradiated materials. Additionally, the matrix concentrations of solute elements in (nonirradiated) Zircaloy-2 were investigated for a series of samples subjected to a annealing at 770◦C followed by cooling at different rates. From these measurements, the solubilities at 770◦C were estimated to be around 65 wt. ppm for chromium, at least 37 wt. ppm for iron, and below 9 wt. ppm for nickel. Slow cooling resulted in virtually no iron, chromium, or nickel in the matrix. The concentration of aluminum in the matrix was observed to be between 10 and 20 wt. ppm for all a-annealed samples and for the as-produced materials of commercial heat treatment.
|
|
| 5. |
- Hosseini, Seyed, 1981, et al.
(författare)
-
Atomic-scale investigation of carbon atom migration in surface induced white layers in high-carbon medium chromium (AISI 52100) bearing steel
- 2017
-
Ingår i: Acta Materialia. - : Elsevier BV. - 1359-6454 .- 1873-2453. ; 130, s. 155-163
-
Tidskriftsartikel (refereegranskat)abstract
- The microstructure and chemical composition of white layers (WLs) formed during hard turning of AISI 52100 steel were studied using atom probe tomography (APT) and transmission electron microscopy (TEM). APT analyses revealed a major difference in the re-distribution of the carbon (C) atoms between WLs formed above and below the Ac1 temperature, i.e. T-WL and M-WL, respectively. In T-WL, the C-atoms segregate to grain boundaries (GBs) forming interconnected or isolated C-rich clusters, ∼5 nm, with a concentration of 9.8 ± 0.3 at.%C. Apart from the GB segregation, in M-WLs, large C-rich regions were found with 24.8 ± 0.4 at.%C. Owing to the chemical composition (stoichiometry) and element partitioning of such regions, they were assigned as θ-carbides (cementite). The APT results reveal that the original θ-carbides remain un-dissolved in the M-WLs, but might be plastically deformed due to the excessive strain that exists in hard machining process. The obtained results are in good agreement with the temperatures that are reached during formation of M-WLs. The isolated nano-sized C-clusters were assigned as off-stoichiometric carbides whereas the interconnected C-rich clusters were attributed to Cottrell atmospheres, evident by the linear shape of the C-enrichment as observed in the APT reconstructions. The C-contents in the nano-sized martensitic and ferritic grains were estimated to 0.50 ± 0.06 at.%C and ∼0.46 ± 0.02 at.%C, respectively. The C-content in the ferritic grains, beyond the C-solubility limit in ferrite (
|
|
| 6. |
- Hulander, Mats, 1974, et al.
(författare)
-
Influence of Fibrinogen on Staphylococcus epidermidis Adhesion Can Be Reversed by Tuning Surface Nanotopography
- 2019
-
Ingår i: ACS Biomaterial Science and Engineering. - : American Chemical Society (ACS). - 2373-9878. ; 5:9, s. 4323-4330
-
Tidskriftsartikel (refereegranskat)abstract
- Surface modifications in the nanoscale regime have shown promising potential in the combat against bacterial adhesion and colonization of surfaces. However, detailed knowledge of how the bacteria-substrate interactions occur is still limited. Herein we have used a gradient in nanostructure density on a surface, realized by immobilizing 40 nm sized silicon dioxide nanoparticles with increasing distance on a glass surface, to systematically study the initial attachment of Staphylococcus epidermidis with or without the presence of human fibrinogen. By using a parallel plate laminar flow chamber, we found a near-linear positive correlation between the adhesion of S. epidermidis with increasing nanoparticle density on unmodified (hydrophilic) nanogradients as well as on gradients where polyethylene glycol was immobilized on the surface in-between nanoparticles. However, if the nanostructured gradient was precoated with human fibrinogen the opposite relationship was observed, although the adsorbed amount of fibrinogen was found to be higher on nanostructured than on smooth surfaces. Our results highlight that even minute changes of the nanotopography on a surface can have profound impact on initial attachment of S. epidermidis to biomaterial surfaces and that the presence of nanostructures strongly hampered the cell's ability to bind to adsorbed fibrinogen, possibly due to changes in the orientation or secondary structure of the fibrinogen molecule upon adsorption.
|
|
| 7. |
- Hörnqvist Colliander, Magnus, 1979, et al.
(författare)
-
Complete precipitate dissolution during adiabatic shear localisation in a Ni-based superalloy
- 2020
-
Ingår i: Philosophical Magazine Letters. - : Informa UK Limited. - 0950-0839 .- 1362-3036. ; 100:12, s. 561-570
-
Tidskriftsartikel (refereegranskat)abstract
- Whereas microstructure evolution in adiabatic shear bands have been thoroughly studied, reports on the stability of hardening precipitates during shear localisation are scarce. We report an atomic scale investigation of solute distribution in adiabatic shear bands in a precipitation strengthened Ni-Fe-based superalloy, showing that the hardening particles are completely dissolved. Temperature estimations indicate that peak temperatures in the shear band above the solvus limits of the precipitates are not unrealistic, and thus diffusion-assisted transformations during the severe plastic deformation cannot be ruled out.
|
|
| 8. |
- Karlsson, Johan, 1984, et al.
(författare)
-
Atomically resolved tissue integration
- 2014
-
Ingår i: Nano Letters. - : American Chemical Society (ACS). - 1530-6992 .- 1530-6984. ; 14:8, s. 4220-4223
-
Tidskriftsartikel (refereegranskat)abstract
- In the field of biomedical technology, a critical aspect is the ability to control and understand the integration of an implantable device in living tissue. Despite the technical advances in the development of biomaterials, the elaborate interplay encompassing materials science and biology on the atomic level is not very well understood. Within implantology, anchoring a biomaterial device into bone tissue is termed osseointegration. In the most accepted theory, osseointegration is defined as an interfacial bonding between implant and bone; however, there is lack of experimental evidence to confirm this. Here we show that atom probe tomography can be used to study the implant-tissue interaction, allowing for three-dimensional atomic mapping of the interface region. Interestingly, our analyses demonstrated that direct contact between Ca atoms and the implanted titanium oxide surface is formed without the presence of a protein interlayer, which means that a pure inorganic interface is created, hence giving experimental support to the current theory of osseointegration. We foresee that this result will be of importance in the development of future biomaterials as well as in the design of in vitro evaluation techniques.
|
|
| 9. |
- Karlsson, Johan, 1984, et al.
(författare)
-
Localized controlled drug delivery from mesoporous implants
- 2014
-
Ingår i: Technical Proceedings of the 2014 NSTI Nanotechnology Conference and Expo, NSTI-Nanotech 2014. Washington, DC, United States, 15-18 June 2014. - 9781482258271
-
Konferensbidrag (refereegranskat)abstract
- Mesoporous materials possess both a well-defined topography on the nanometer scale, and they may serve as hosts for drugs. In this work, titanium implants coated with mesoporous TiO2 thin films have been evaluated both in vitro and in vivo. Material characterization showed that, long-range ordered mesoporous TiO2, with a pore-size of 6 nm, and a narrow pore-size distribution were obtained. An in vivo study demonstrated that the films were robust enough to withstand the implantation procedure. The in vitro apatite formation experiments showed that formation of apatite was higher on the mesoporous surface compared to its nonporous counterpart. In a separate in vivo study, two osteoporosis drugs, alendronate (ALN) and raloxifene (RLX), were immobilised into the nanoporous oxide films. The in vitro drug release tests carried out showed a sustained release of both drugs. The osteogenic response after 28 days of implantation of the drug-loaded implants showed a significantly improved bone fixation.
|
|
| 10. |
- Kuczyńska-Zemła, D., et al.
(författare)
-
The distribution of O and N in the surface region of laser-patterned titanium revealed by atom probe tomography
- 2021
-
Ingår i: Applied Surface Science. - : Elsevier BV. - 0169-4332. ; 562
-
Tidskriftsartikel (refereegranskat)abstract
- Direct Laser Interference Lithography (DLIL) has shown to be a promising technique to chemically and physically alter the surface of titanium. In this work, atom probe tomography analysis was performed on DLIL-treated titanium to obtain the chemical composition of the surface in maxima and minima interference positions. The analysis revealed that a multilayer structure consisting of oxide/oxynitride is formed at both positions; however, the chemical composition is altered differently between the two. The observed difference is believed to be due to an uneven heating and temperature distribution, which is demonstrated by thermal simulations.
|
|
