| 1. |
- Moberg, Christina, et al.
(författare)
-
De unga gör helt rätt när de stämmer staten
- 2022
-
Ingår i: Aftonbladet. - 1103-9000.
-
Tidskriftsartikel (populärvet., debatt m.m.)abstract
- 1 620 forskare och lärare i forskarvärlden: Vi ställer oss bakom Auroras klimatkrav
|
|
| 2. |
- Ahlberg, Erik, et al.
(författare)
-
"Vi klimatforskare stödjer Greta och skolungdomarna"
- 2019
-
Ingår i: Dagens nyheter (DN debatt). - 1101-2447.
-
Tidskriftsartikel (populärvet., debatt m.m.)abstract
- DN DEBATT 15/3. Sedan industrialiseringens början har vi använt omkring fyra femtedelar av den mängd fossilt kol som får förbrännas för att vi ska klara Parisavtalet. Vi har bara en femtedel kvar och det är bråttom att kraftigt reducera utsläppen. Det har Greta Thunberg och de strejkande ungdomarna förstått. Därför stödjer vi deras krav, skriver 270 klimatforskare.
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
- Davidsson, Kent, 1967, et al.
(författare)
-
Potassium, chlorine, and sulfur in ash, particles, deposits, and corrosion during wood combustion in a circulating fluidized-bed boiler
- 2007
-
Ingår i: Energy & Fuels. - : American Chemical Society (ACS). - 1520-5029 .- 0887-0624. ; 21:1, s. 71-81
-
Tidskriftsartikel (refereegranskat)abstract
- The effect of the addition of chlorine and/or sulfur to the fuel on fly ash composition, deposit formation, and superheater corrosion has been studied during biomass combustion in a circulating fluidized-bed boiler. The chlorine (HCl (aq)) and sulfur (SO2 (g)) were added in proportions of relevance for the potassium chemistry. The composition of the bottom and the fly ashes was analyzed. Gas and particle measurements were performed downstream of the cyclone before the convection pass and the flue gas composition was recorded in the stack with a series of standard instruments and an FTIR analyzer. At the position downstream of the cyclone, a deposit probe was situated, simulating a superheater tube. Deposits on the probe and initial corrosion were examined. It is concluded that addition of sulfur and chlorine increases the formation of submicron particles leading to deposition of potassium sulfate and chloride. The results compare well with earlier work based on laboratory-scale experiments concerning effects of chlorine and sulfur on potassium chemistry.
|
|
| 6. |
- Fröberg, Linus, et al.
(författare)
-
Vertical InAs nanowire wrap-gate FETs
- 2006
-
Ingår i: Book of abstracts: Semicond Nanowires Symp, Eindhoven, The Netherlands (2006).
-
Konferensbidrag (refereegranskat)
|
|
| 7. |
|
|
| 8. |
- Krishnaraja, Abinaya, et al.
(författare)
-
Tuning of Source Material for InAs/InGaAsSb/GaSb Application-Specific Vertical Nanowire Tunnel FETs
- 2020
-
Ingår i: ACS Applied Electronic Materials. - : American Chemical Society (ACS). - 2637-6113. ; 2:9, s. 2882-2887
-
Tidskriftsartikel (refereegranskat)abstract
- Tunnel field-effect transistors (TFETs) are promising candidates that have demonstrated potential for and beyond the 3 nm technology node. One major challenge for the TFETs is to optimize the heterojunction for high drive currents while achieving steep switching. Thus far, such optimization has mainly been addressed theoretically. Here, we experimentally investigate the influence of the source segment composition on the performance for vertical nanowire InAs/InGaAsSb/GaSb TFETs. Compositional analysis using transmission electron microscopy is combined with simulations to interpret the results from electrical characterization data. The results show that subthreshold swing (S) and transconductance (gm) decrease with increasing arsenic composition until the strain due to lattice mismatch increases them both. The role of indium concentration at the junction is also examined. This systematic optimization has rendered sub-40 mV/dec operating TFETs with a record transconductance efficiency gm/ID = 100 V-1, and it shows that different source materials are preferred for various applications.
|
|
| 9. |
- Steffenburg-Nordenström, Joachim, 1962-
(författare)
-
Process chain simulation of forming, welding and heat treatment of Alloy 718
- 2017
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Manufacturing of aero engine components requires attention to residual stress and final shape of the product in order to meet high quality product standards.This sets very high demands on involved manufacturing steps to meet design requirements. Simulation of manufacturing processes can therefore be animportant tool to contribute to quality assurance.The focus in this work is on simulation of a manufacturing process chain comprising of sheet metal forming, welding and a stress relief heat treatment.Simulation of sheet metal forming can be used to design a forming tool design that accounts for the material behaviour, e.g. spring back, and avoid problems such as wrinkling, thinning and cracking. Moreover, the simulation can also show how the material is stretched and work hardened. The residual stresses after forming may be of local character or global depending on the shape that is formed. However, the heat affected zone due to welding is located near the weld.The weld also causes large residual stresses with the major component along the weld. It is found that the magnitude of the residual stresses after welding is affected by remaining stresses from the previous sheet metal forming. The final stress relieve treatment will relax these residual stresses caused by e.g. forming and welding. However, this causes additional deformations.The main focus of this study is on how a manufacturing process step affects the subsequent step when manufacturing a component of the nickel-based super alloy 718. The chosen route and geometry is a simplified leading edge of an exhaust case guide vane. The simulations were validated versus experiments. The computed deformations were compared with measurements after each manufacturing step. The overall agreement between experiments and measurement was good. However, not sufficiently accurate considering the required tolerance of the component. It was found from simulations that the residual stresses after each process affects the subsequent step. After a complete manufacturing process chain which ends with a stress relief heat treatment the residual stresses were not negligible. VIII Special experiments were performed for studying the stress relief in order to understand how the stresses evolve through the heat treatment cycle during relaxation. It was found that the stresses were reduced already during the beginning of the heating up sequence due to decreasing Young´s modulus and yield stress with increasing temperature. Relaxation due to creep starts when a certain temperature was reached which gave a permanent stress relief.
|
|
| 10. |
|
|
