| 1. |
- Chatzigiannakou, Maria Angeliki, et al.
(författare)
-
Offshore deployments of wave energy converters by Uppsala University, Sweden
- 2019
-
Ingår i: Marine Systems and Ocean Technology. - : Springer Science and Business Media LLC. - 1679-396X .- 2199-4749. ; 14:2-3, s. 67-74
-
Tidskriftsartikel (refereegranskat)abstract
- Ocean can provide an inexhaustible amount of energy. Many marine energy converters have been developed but most of them have not surpassed the experimental phase due to the high costs in installation, operation, and maintenance. Since 2002 Uppsala University has developed and deployed several units of wave energy converters of various designs. The Uppsala University wave energy converter concept consists of a linear generator directly connected to a point absorber buoy that is mounted on a concrete gravity foundation. Uppsala University deployments have been carried out using different deployment vessels and methods. Three main methods were utilized for these deployments that are discussed in terms of cost, manpower, and time efficiency. Depending on the desired outcome—multiple- or single-device deployment, low budget, etc.—one of the proposed methods can be used for the optimal outcome.
|
|
| 2. |
- Parwal, Arvind, et al.
(författare)
-
Grid impact and power quality assessment of wave energy parks: Different layouts and power penetrations using energy storage
- 2021
-
Ingår i: JOURNAL OF ENGINEERING-JOE. - : Institution of Engineering and Technology (IET). - 2051-3305. ; 2021:8, s. 415-428
-
Tidskriftsartikel (refereegranskat)abstract
- Power fluctuations induced by wave energy converters (WECs) may reflect negative impact on the power quality of the power grid. Assessing their impact is an important step to ensure the grid compliance level of the energy park. The IEC 61000-4-15 standard classifies the allowable disturbances in the grid. This study analysed and assessed the grid impact in terms of flicker, harmonic distortion and voltage variations. The assessments were performed without energy storage and compared when using the energy storage. A single WEC is emulated as an irregular power output of a real WEC using a combined model of power take-off in the Simulink model. Time series based on data obtained in earlier offshore experiments, conducted at the Lysekil research site in Sweden, is used to emulate a wave energy park (WEP) power in a land-based test rig in real-time power hardware-in-the-loop simulations. A total of three and ten WECs are emulated by introducing a time delay in the time series to investigate the grid impact in each layout. Flicker emissions, voltage variations, individual and total harmonics of the voltage at the connection point in each layout are studied and compared with the limits to be grid compliant for layouts of the WEP. In addition, voltage and current harmonics for the single WEC and individual harmonics in each phase of the voltage are measured and analysed to assess the compliance level of the WEP.
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
- Chatzigiannakou, Maria Angeliki, et al.
(författare)
-
Numerical analysis of an Uppsala University WEC deployment by a barge for different sea states
- 2020
-
Ingår i: Ocean Engineering. - : Elsevier BV. - 0029-8018 .- 1873-5258. ; 205
-
Tidskriftsartikel (refereegranskat)abstract
- Wave energy converters (WECs) have been deployed onshore, nearshore, and offshore to convert ocean wave movement into electricity. The exploitation of renewable energy sources has restrictions; in the case of wave energy, high installation, maintenance, and decommissioning costs have limited their commercial use. Moreover, these offshore operations can be compromised by safety issues. This paper draws attention to offshore operation safety of a WEC developed by Uppsala University. Specifically, this paper investigates what sea states are suitable for the safe deployment of a WEC from a barge. This study follows recommendations in DNV-RP-H103 for analysis of offshore operations, namely lifting through the wave zone. ANSYS Aqwa is used to find hydrodynamic forces acting on a typical barge, using frequency domain analysis. Based on these hydrodynamic simulation results and methodology given in DNV-RP-H103, tables are created to show the sea states that would allow for the safe installation of a WEC using a typical barge. Considered sea states have significant wave heights varying between 0 m and 3 m and the wave zero crossing periods varying between 3 s and 13 s. The WEC submersions are considered between 0 m and 7 m, i.e. when the WEC is in the air until it is fully submerged. © 2020 Elsevier Ltd
|
|
| 6. |
- Chatzigiannakou, Maria Angeliki
(författare)
-
Offshore deployments of marine energy converters
- 2019
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The depletion warning of non-renewable resources, such as gas, coal and oil, and the imminent effects of climate change turned the attention to clean and fossil fuel-free generated electricity. University research groups worldwide are studying solar, wind, geothermal, biomass and ocean energy harvesting. The focus of this thesis is the wave and marine current energy researched at the division of Electricity at Uppsala University (UU). The main drawbacks that hinder the commercialization of marine energy converter devices is a high installation, operation, maintenance and decommissioning cost. Furthermore, these processes are highly weather dependent and thus, can be time consuming beyond planning. In this thesis, an evaluation of the cost, time and safety efficiency of the devices’ offshore deployment (both wave and marine current), and a comparative evaluation regarding the safety in the use of divers and remotely operated vehicles (ROVs) are conducted. Moreover, a risk analysis study for a common deployment barge while installing an UU wave energy converter (WEC) is presented with the aim to investigate the failure of the crane hoisting system.The UU wave energy project have been initiated in 2001, and since then 14 WECs of various designs have been developed and deployed offshore, at the Lysekil research site (LRS), on the Swedish west coast and in Åland, Finland. The UU device is a point absorber with a linear generator power take off. It is secured on the seabed by a concrete gravity foundation. The absorbed wave energy is transmitted to shore through the marine substation (MS) where all the generators are interconnected. In 2008 an UU spin-off company, Seabased AB (SAB), was established and so far has developed and installed several WECs and two MSs, after the UU devices main principle. SAB deployments were conducted in Sotenäs, Sweden, at the Maren test site (MTS) in Norway; and in Ada Foah, Ghana. The active participation and the thorough study of the above deployments led to a cost, time and safety evaluation of the methods followed. Four main methods were identified and the most suitable one can be chosen depending on the deployment type, for example, for single or mass device deployment.The first UU full scale marine current energy converter (MCEC) was constructed in 2007 at the Ångström Laboratory and deployed at Söderfors, in the river Dalälven in March 2013. The UU turbine is of a vertical axis type and is connected to a directly driven permanent magnet synchronous generator of a low-speed. With this deployment as an example, four MCEC installation methods were proposed and evaluated in terms of cost and time efficiency.A comparative study on the use of divers and ROVs for the deployment and maintenance of WECs at the LRS has been carried out, showing the potential time and costs saved when using ROVs instead of divers in underwater operations. The main restrictions when using divers and ROVs were presented. Most importantly, the modelling introduced is generalized for most types of wave energy technologies, since it does not depend on the structure size or type.Finally, a table of safe launch operation of a WEC is presented. In this table the safe, restrictive and prohibitive sea states are found for a single WEC deployment, using a barge and a crane placed on it. The table can be utilized as a guidance for offshore operations safety and can be extended for a variety of device types and vessels.
|
|
| 7. |
- Fjellstedt, Christoffer, et al.
(författare)
-
A Review of AC and DC Collection Grids for Offshore Renewable Energy with a Qualitative Evaluation for Marine Energy Resources
- 2022
-
Ingår i: Energies. - : MDPI. - 1996-1073. ; 15:16
-
Tidskriftsartikel (refereegranskat)abstract
- Marine energy resources could be crucial in meeting the increased demand for clean electricity. To enable the use of marine energy resources, developing efficient and durable offshore electrical systems is vital. Currently, there are no large-scale commercial projects with marine energy resources, and the question of how to design such electrical systems is still not settled. A natural starting point in investigating this is to draw on experiences and research from offshore wind power. This article reviews different collection grid topologies and key components for AC and DC grid structures. The review covers aspects such as the type of components, operation and estimated costs of commercially available components. A DC collection grid can be especially suitable for offshore marine energy resources, since the transmission losses are expected to be lower, and the electrical components could possibly be made smaller. Therefore, five DC collection grid topologies are proposed and qualitatively evaluated for marine energy resources using submerged and non-submerged marine energy converters. The properties, advantages and disadvantages of the proposed topologies are discussed, and it is concluded that a suitable electrical system for a marine energy farm will most surely be based on a site-specific techno-economic analysis.
|
|
| 8. |
|
|
| 9. |
- Frost, Anna E., 1988-
(författare)
-
In the Air Gap of Linear Generators for Wave Power
- 2021
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Wave power conversion is one type of renewable electricity generation. Within wave power, there are many different concepts, whereof some utilizes linear generators for converting the energy in the ocean waves into electricity. A linear generator consists of a translator, which is moving and have magnets of alternating polarity, and a stator, which have conductors sur-rounded by laminated steel. Between the translator and stator is an air gap, which is only a few millimeters wide. All linear generators for wave power, to the author’s knowledge, are permanent-magnet synchronous generators. This thesis looks into the forces and power flow in the air gap of linear generators for wave power, with the purpose of improving their future performance. The studies have focused on permanent magnet synchronous generators for wave power, but several of the results should also be applicable for other applications of linear elec-trical machines.Depending on the design of the linear generators, the translator can move so long that it only partially overlap the stator. This is common among several different wave power concepts with linear generators. When the stator is only partially overlapped by the stator it is denoted as partial stator overlap. It is studied how partial stator overlap affects the generated electric-ity, the absorbed energy, and the tangential and normal force in the air gap. The generated electricity and absorbed energy of a linear generator are quadratically dependent on the partial stator-translator overlap is shown through Faraday’s law and simulations. Experimental data showed that the absorbed energy is both linearly and quadratic depending on partial stator over-lap, where the linear dependence is at least partially due to frictional losses. Simulated results confirm that voltage is linearly dependent on partial stator overlap, which means quadratic de-pendence between generated electric and partial stator overlap. The simulated forces showed a linear dependence.Decades ago, the Poynting vector was used to derive an expression for the power flow in the air gap of rotating electrical machines. In this thesis the equivalent expressions for both flat and tubular linear electrical machines were derived. The analytical results were also compared with results from simulations. Both the analytical expressions and simulations showed that tubular and flat linear electrical machines have slightly different behavior.
|
|
| 10. |
- Frost, Anna E., 1988-, et al.
(författare)
-
Power flow in the air gap of linear electrical machines by utilization of the Poynting vector : Part 1 - Analytical expressions
- 2022
-
Ingår i: The Journal of Engineering. - : Institution of Engineering and Technology (IET). - 2051-3305. ; 2022:4, s. 377-388
-
Tidskriftsartikel (refereegranskat)abstract
- Analytical solutions and estimations for the power flow in the air gap of linear electrical machines of different geometries are derived from Poynting's theorem. The different geometries considered are flat one-sided, multi-sided, and tubular linear electrical machines. The radial power flow for all considered geometries is dependent on the area of the air gap, the electric field, the magnetic field, and the load angle. The tangential power flow for both flat one-sided and tubular linear electrical machines is dependent of the area of the air gap, number of poles, the electric field, the magnetic field, and the load angle. The number of poles could be increased to decrease the tangential power flow in flat linear electrical machines. The expression for the tangential flow in tubular linear electrical machines is so complicated that it is difficult to draw conclusions from it.
|
|
