| 1. |
- Engberg, David L. J., 1986-, et al.
(författare)
-
Atom probe tomography field evaporation characteristics and compositional corrections of ZrB2
- 2019
-
Ingår i: Materials Characterization. - : Elsevier BV. - 1044-5803 .- 1873-4189. ; 156
-
Tidskriftsartikel (refereegranskat)abstract
- The microstructure of stoichiometric ZrB2.0 and B over-stoichiometric ZrB2.5 thin films has been studied using atom probe tomography (APT), X-ray diffraction, and transmission electron microscopy. Both films consist of columnar ZrB2 grains with AlB2-type crystal structure. The narrow stoichiometry range of ZrB2 results in the presence of separate disordered B-rich boundaries even in ZrB2.0. At higher average B content, specifically ZrB2.5, the formation of a continuous network around the sides of the ZrB2 columns is promoted. In addition, the APT field evaporation characteristics of ZrB2 and its influence on the measured local composition has been studied and compared to the average composition from elastic recoil detection analysis (ERDA). Differences in the measured average compositions of the two techniques are explained by the APT detector dead-time/space. A new pile-up pairs correction procedure based on co-evaporation correlation data was thus employed here for the APT data and compared with the 10B-method (the B equivalence of the 13C-method), as well as the combination of both methods. In ZrB2.0, all of the applied compositional correction methods were found to reduce the compositional difference when appropriate isotopic abundances were used. In ZrB2.5, the inhomogeneity of the film likely increased the local APT composition to such an extent that even conservative correction procedures overestimated the B content compared to the ERDA reference. The strengths of the pile-up pairs correction compared the 10B and the combined methods are higher precision, due to it being less dependent on the accuracy of estimated isotopic abundances, and that the correction itself is not dependent on careful background correction of the mass spectrum.
|
|
| 2. |
- Krupp, Ulrich, 1968, et al.
(författare)
-
The potential of spinodal ferrite decomposition for increasing the very high cycle fatigue strength of duplex stainless steel
- 2016
-
Ingår i: International Journal of Fatigue. - : Elsevier BV. - 0142-1123. ; 93, s. 363-371
-
Tidskriftsartikel (refereegranskat)abstract
- Duplex stainless steels (DSS) have become candidate materials for structural applications, where conventional austenitic stainless steels fail due to very high cycle fatigue (VHCF) in combination with corrosive attack. It seems that DSS exhibit a fatigue limit, which can be attributed to the two-phase austenitic-ferritic microstructure. Ultrasonic VHCF testing revealed that the phase boundaries are efficient obstacles for the transmission of slip bands and microstructural fatigue cracks up to 10(9) cycles and even beyond. The barrier strength is determined by the misorientation relationship between neighbouring grains but also by the strength of the individual phases. By thermal treatment at 475 degrees C, spinodal decomposition of the ferrite phase results in the formation of Cr-rich alpha' precipitates. While during static loading these precipitates give rise to a loss in ductility (475 degrees C embrittlement), it was shown that the HCF strength can be increased and that there is also a tendency towards a beneficial effect on the VHCF behaviour. A more detailed analysis of the local plasticity sites by means of atom probe tomography (APT) revealed a dissolution of the a' precipitates within operated slip bands. The dissolution might be an indication for a local softening mechanism that limits the VHCF strengthening effect of spinodal decomposition.
|
|
| 3. |
- Aboulfadl, Hisham, 1986, et al.
(författare)
-
Alkali Dispersion in (Ag,Cu)(In,Ga)Se2 Thin Film Solar Cells - Insight from Theory and Experiment
- 2021
-
Ingår i: ACS Applied Materials & Interfaces. - : American Chemical Society (ACS). - 1944-8252 .- 1944-8244. ; 13:6, s. 7188-7199
-
Tidskriftsartikel (refereegranskat)abstract
- Silver alloying of Cu(In,Ga)Se2 absorbers for thin film photovoltaics offers improvements in open-circuit voltage, especially when combined with optimal alkali-treatments and certain Ga concentrations. The relationship between alkali distribution in the absorber and Ag alloying is investigated here, combining experimental and theoretical studies. Atom probe tomography analysis is implemented to quantify the local composition in grain interiors and at grain boundaries. The Na concentration in the bulk increases up to ∼60 ppm for [Ag]/([Ag] + [Cu]) = 0.2 compared to ∼20 ppm for films without Ag and up to ∼200 ppm for [Ag]/([Ag] + [Cu]) = 1.0. First-principles calculations were employed to evaluate the formation energies of alkali-on-group-I defects (where group-I refers to Ag and Cu) in (Ag,Cu)(In,Ga)Se2 as a function of the Ag and Ga contents. The computational results demonstrate strong agreement with the nanoscale analysis results, revealing a clear trend of increased alkali bulk solubility with the Ag concentration. The present study, therefore, provides a more nuanced understanding of the role of Ag in the enhanced performance of the respective photovoltaic devices.
|
|
| 4. |
- Aboulfadl, Hisham, et al.
(författare)
-
Microstructural Characterization of Sulfurization Effects in Cu(In,Ga)Se2 Thin Film Solar Cells
- 2019
-
Ingår i: Microscopy and Microanalysis. - : CAMBRIDGE UNIV PRESS. - 1435-8115 .- 1431-9276. ; 25:2, s. 532-538
-
Tidskriftsartikel (refereegranskat)abstract
- Surface sulfurization of Cu(In,Ga)Se 2 (CIGSe) absorbers is a commonly applied technique to improve the conversion efficiency of the corresponding solar cells, via increasing the bandgap towards the heterojunction. However, the resulting device performance is understood to be highly dependent on the thermodynamic stability of the chalcogenide structure at the upper region of the absorber. The present investigation provides a high-resolution chemical analysis, using energy dispersive X-ray spectrometry and laser-pulsed atom probe tomography, to determine the sulfur incorporation and chemical re-distribution in the absorber material. The post-sulfurization treatment was performed by exposing the CIGSe surface to elemental sulfur vapor for 20 min at 500°C. Two distinct sulfur-rich phases were found at the surface of the absorber exhibiting a layered structure showing In-rich and Ga-rich zones, respectively. Furthermore, sulfur atoms were found to segregate at the absorber grain boundaries showing concentrations up to ∼7 at% with traces of diffusion outwards into the grain interior.
|
|
| 5. |
- Adegoke, Olutayo, et al.
(författare)
-
Scanning electron microscopy and atom probe tomography characterization of laser powder bed fusion precipitation strengthening nickel-based superalloy
- 2023
-
Ingår i: Micron. - 0968-4328 .- 1878-4291. ; 171
-
Tidskriftsartikel (refereegranskat)abstract
- Atom probe tomography (APT) was utilized to supplement scanning electron microscopy (SEM) characterizationof a precipitation strengthening nickel-based superalloy, Alloy 247LC, processed by laser powder bed fusion (LPBF). It was observed that the material in the as-built condition had a relatively high strength. Using both SEMand APT, it was concluded that the high strength was not attributed to the typical precipitation strengtheningeffect of γ’. In the absence of γ’ it could be reasonably inferred that the numerous black dots observed in thecells/grains with SEM were dislocations and as such should be contributing significantly to the strengthening.Thus, the current investigation demonstrated that relatively high strengthening can be attained in L-PBF even inthe absence of precipitated γ’. Even though γ’ was not precipitated, the APT analysis displayed a nanometer scalepartitioning of Cr that could be contributing to the strengthening. After heat-treatment, γ’ was precipitated and itdemonstrated the expected high strengthening behavior. Al, Ta and Ti partitioned to γ’. The strong partitioningof Ta in γ’ is indicative that the element, together with Al and Ti, was contributing to the strain-age crackingoccurring during heat-treatment. Cr, Mo and Co partitioned to the matrix γ phase. Hf, Ta, Ti and W were found inthe carbides corroborating previous reports that they are MC.
|
|
| 6. |
- Angseryd, Jenny, 1979, et al.
(författare)
-
Quantitative APT analysis of Ti(C,N)
- 2011
-
Ingår i: Ultramicroscopy. - : Elsevier BV. - 1879-2723 .- 0304-3991. ; 111:6, s. 609-614
-
Tidskriftsartikel (refereegranskat)abstract
- A specially produced Ti(C,N) standard material, with a known nominal composition, was investigated with laser assisted atom probe tomography. The occurrence of molecular ions and single/multiple events was found to be influenced by the laser pulse energy, and especially C related events were affected. Primarily two issues were considered when the composition of Ti(C,N) was determined. The first one is connected to detector efficiency, due to the detector dead-time. The second one is connected to peak overlap in the mass spectrum. A method is proposed for quantification of the C content in order to establish the C/N ratio. A correction was made to the major C peaks, C at 6 and 12 Da, with the 13C isotopes, at 6.5 and 13 Da, according to the known natural abundance. In addition, a correction of the peak at 24 Da, where C and Ti overlap, is proposed based on the occurrence of single/multiple events for respective element. The results were compared to the results from other techniques such as electron energy loss spectroscopy, chemical analysis and X-ray diffraction. After applying the corrections, atom probe tomography results were satisfactory. Furthermore, the content of dissolved O in Ti(C,N) was successfully quantified. © 2011 Elsevier B.V.
|
|
| 7. |
- Bjurman, Martin, et al.
(författare)
-
Microstructural evolution of welded stainless steels on integrated effect of thermal aging and low flux irradiation
- 2019
-
Ingår i: Minerals, Metals and Materials Series. - : Springer International Publishing. - 2367-1696 .- 2367-1181. ; Part F11, s. 703-710
-
Konferensbidrag (refereegranskat)abstract
- The combined effect of thermal aging and irradiation on cast and welded stainless steel solidification structures is not sufficiently investigated. From theory and consecutive aging and irradiation experiments, the effect of simultaneous low rate irradiation and thermal aging is expected to accelerate and modify the aging processes of the ferrite phase. Here, a detailed analysis of long-term aged material at very low fast neutron flux at LWR operating temperatures using Atom Probe Tomography is presented. Samples of weld material from various positions in the core barrel of the Zorita PWR are examined. The welds have been exposed to 280–285 °C for 38 years at three different neutron fluxes between 1 × 10 −5 and 7 × 10 −7 dpa/h to a total dose of 0.15–2 dpa. The aging of the ferrite phase occurs by spinodal decomposition, clustering and precipitation of e.g. G-phase. These phenomena are characterized and quantitatively analyzed in order to understand the effect of flux in combination with thermal aging.
|
|
| 8. |
- Boll, Torben, 1979, et al.
(författare)
-
An APT investigation of an amorphous Cr-B-C thin film
- 2015
-
Ingår i: Ultramicroscopy. - : Elsevier BV. - 1879-2723 .- 0304-3991. ; 159, s. 217-222
-
Tidskriftsartikel (refereegranskat)abstract
- A magnetron sputtered amorphous Cr-B-C thin film was investigated by means of atom probe tomography (APT). The film is constituted of two phases; a Cr-rich phase present as a few nanometer large regions embedded in a Cr-poor phase (tissue phase). The Cr-rich regions form columnar chains oriented parallel to the growth direction of the film. It was found that the Cr-rich regions have a higher B:C ratio than the Cr-poor regions. The composition of the phases was determined as approximately 35Cr-33B-30C and 15Cr-40B-42C (at%), respectively. The results suggest that this type of nanocomposite films has a more complex structure than previously anticipated, which may have an importance for the mechanical and electrical properties.
|
|
| 9. |
- Boåsen, Magnus, et al.
(författare)
-
Analysis of thermal embrittlement of a low alloy steel weldment using fracture toughness and microstructural investigations
- 2022
-
Ingår i: Engineering Fracture Mechanics. - : Elsevier BV. - 0013-7944 .- 1873-7315. ; 262
-
Tidskriftsartikel (refereegranskat)abstract
- A thermally aged low alloy steel weld metal is investigated in terms of its fracture toughness and microstructural evolution and compared to a reference. The main purpose of the study is to investigate the effects of embrittlement due to thermal ageing on the brittle fracture toughness, and its effects on the influence of loss of crack tip constraint. The comparison of the investigated materials has been made at temperatures that give the same median fracture toughness of the high constraint specimens, ensuring comparability of the low constraint specimens. Ageing appears to enable brittle fracture initiation from grain boundaries besides initiation from second phase particles, making the fracture toughness distribution bimodal. Consequently, this appears to reduce the facture toughness of the low constraint specimens of the aged material as compared to the reference material. The microstructure is investigated at the nano scale using atom probe tomography where nanometer sized Ni-Mn-rich clusters, precipitated during ageing, are found primarily situated on dislocation lines.
|
|
| 10. |
- Bushlya, Volodymyr, et al.
(författare)
-
Tool wear mechanisms of PcBN in machining Inconel 718: Analysis across multiple length scale
- 2021
-
Ingår i: CIRP Annals - Manufacturing Technology. - : Elsevier BV. - 1726-0604 .- 0007-8506. ; 70:1, s. 73-78
-
Tidskriftsartikel (refereegranskat)abstract
- Recently, PcBN tooling have been successfully introduced in machining Ni-based superalloys, yet our knowledge of involved wear mechanisms remains limited. In this study, an in-depth investigation of PcBN tool degradation and related wear mechanisms when machining Inconel 718 was performed. Diffusional dissolution of cBN is an active wear mechanism. At high cutting speed oxidation of cBN becomes equally important. Apart from degradation, tool protection phenomena were also discovered. Oxidation of Inconel 718 resulted in formation of γ-Al2O3 and (Al,Cr,Ti)3O4 spinel that were deposited on the tool rake. Also on the rake, formation of (Ti,Nb,Cr)N takes place due to cBN-workpiece interaction. This creates a sandwich tool protection layer forming continuously as tool wear progresses. Such in operando protection enabled counterbalancing tool wear mechanisms and achieved high performance of PcBN in machining.
|
|
