| 1. |
- Beal, Jacob, et al.
(författare)
-
Robust estimation of bacterial cell count from optical density
- 2020
-
Ingår i: Communications Biology. - : Springer Science and Business Media LLC. - 2399-3642. ; 3:1
-
Tidskriftsartikel (refereegranskat)abstract
- Optical density (OD) is widely used to estimate the density of cells in liquid culture, but cannot be compared between instruments without a standardized calibration protocol and is challenging to relate to actual cell count. We address this with an interlaboratory study comparing three simple, low-cost, and highly accessible OD calibration protocols across 244 laboratories, applied to eight strains of constitutive GFP-expressing E. coli. Based on our results, we recommend calibrating OD to estimated cell count using serial dilution of silica microspheres, which produces highly precise calibration (95.5% of residuals <1.2-fold), is easily assessed for quality control, also assesses instrument effective linear range, and can be combined with fluorescence calibration to obtain units of Molecules of Equivalent Fluorescein (MEFL) per cell, allowing direct comparison and data fusion with flow cytometry measurements: in our study, fluorescence per cell measurements showed only a 1.07-fold mean difference between plate reader and flow cytometry data.
|
|
| 2. |
- Du, Xinyu, et al.
(författare)
-
Distribution, behavior, and risk assessment of chlorinated paraffins in paddy plants throughout whole growth cycle
- 2022
-
Ingår i: Environment International. - : Elsevier BV. - 0160-4120 .- 1873-6750. ; 167
-
Tidskriftsartikel (refereegranskat)abstract
- Paddy plants provide staple food for 3 billion people worldwide. This study explores the environmental fate and behavior of a high-volume production emerging contaminants chlorinated paraffins (CPs) in the paddy ecosystem. Very-short-, short-, medium-, and long-chain CPs (vSCCPs, SCCPs, MCCPs, and LCCPs, respectively) were analyzed in specific tissue of paddy plants at four main growth stages and soils from the Yangtze River Delta, China throughout a full rice growing season. The total CP concentrations in the paddy roots, stalks, leaves, panicles, hulls, rice, and soils ranged from 181 to 1.74 × 103, 21.7–383, 19.6–585, 108–332, 245–470, 59.6–130, and 99.6–400 ng/g dry weight, respectively. The distribution profile indicated the translocation of SCCPs and MCCPs from soils to paddy tissue, highlighting their elevated bioaccumulative potential. The evolution of CP level/mass/pattern during the whole growth cycle suggested atmospheric CPs deposition on leaves and hulls, as well as stalk-rice transfer. CSOIL plant uptake model well predicted the level, distribution pattern, and bioconcentration factors (BCFs) of SCCPs and MCCPs in paddy shoot and recognized the soil-air-shoot pathway as the major contributor. Moreover, risk evaluation indicated that MCCPs intake and subsequent risks dominated the total exposure to CPs via rice ingestion. This is the first report on the occurrence, fate and risk assessment of all CPs classes in paddy ecosystems, and the results underline the potential health effects caused by the in-use MCCPs via rice ingestion.
|
|
| 3. |
- Ji, Xinyu, et al.
(författare)
-
Two-phase flow characteristics and visualization of distributed confined array jet boiling
- 2024
-
Ingår i: Case Studies in Thermal Engineering. - 2214-157X. ; 57
-
Tidskriftsartikel (refereegranskat)abstract
- Confined array jet boiling can achieve high heat flux in a compact space and its flow resistance characteristics are critical to the design of cooling systems. The boiling images of distributed confined jet of HFE-7100 is recorded by a high-speed camera in this study. The effects of jet mass flux, jet height and surface structure of two-phase jet flow characteristics on micro-pin-finned surfaces are studied. A benefit from the distributed configuration of the jet array, in contrast to previous studies, is that the jet boiling pressure drop is independent of the heat flux, but only related to the jet mass flux. The effect of the surface structure on the pressure drop is negligible. Jet flow instability will be triggered by intermittently blockage of the jet inlet and outlet by large vapor masses in certain heated surfaces. Reducing the jet height can suppress two-phase flow instabilities while keeping the pressure drop almost constant and the CHF to slightly increase. The COP of distributed jet impingement boiling cooler proposed in this work can be up to 6 times higher than that of the conventional jet boiling cooler, and more than 2 times higher that of the microchannel heat sink.
|
|
| 4. |
- Li, Xinyu, et al.
(författare)
-
Biodegradable MOFilters for Effective Air Filtration and Sterilization by Coupling MOF Functionalization and Mechanical Polarization of Fibrous Poly(lactic acid)
- 2023
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 15:22, s. 26812-26823
-
Tidskriftsartikel (refereegranskat)abstract
- High-performance air filtration materials are importantfor addressingthe airborne pollutants. Herein, we propose an unprecedented accessto biodegradable poly-(lactic acid) (PLA)-based MOFilters with excellentfiltering performance and antibacterial activity. The fabricationinvolved a stepwise in situ growth of zeolitic imidazolate framework-8(ZIF-8) crystals at the surface of microfibrous PLA membranes, followedby mechanical polarization under high pressure and low temperature(5 MPa, 40 degrees C) to trigger the ordered alignment of dipoles inPLA chains and ZIF-8. The unique structural features allowed thesePLA-based MOFilters to achieve an exceptional combination of excellenttensile properties, high dielectric constant (up to 2.4 F/m), andenhanced surface potential as high as 4 kV. Arising from the remarkablesurface activity and electrostatic adsorption effect, a significantincrease (from over 12% to nearly 20%) in PM0.3 filtrationefficiency was observed for the PLA-based MOFilters compared to thatof pure PLA counterparts, with weak relation to the airflow velocities(10-85 L/min). Moreover, the air resistance was controlledat a considerably low level for all the MOFilters, that is, below183 Pa even at 85 L/min. It is worth noting that distinct antibacterialproperties were achieved for the MOFilters, as illustrated by theinhibitive rates of 87 and 100% against Escherichiacoli and Staphylococcus aureus, respectively. The proposed concept of PLA-based MOFilters offersunprecedented multifunction integration, which may fuel the developmentof biodegradable versatile filters with high capturing and antibacterialperformances yet desirable manufacturing feasibility.
|
|
| 5. |
- Liu, Zhan, et al.
(författare)
-
Effect of phase change heat storage tank with gradient fin structure on solar energy storage : A numerical study
- 2023
-
Ingår i: International Journal of Heat and Mass Transfer. - 0017-9310. ; 215
-
Tidskriftsartikel (refereegranskat)abstract
- In this paper, the heat storage process of a latent heat thermal energy storage (LHTES) tank is studied numerically. A new type of gradient fin is added to the heat storage process in a latent heat storage tank to improve the heat transfer performance of the internal phase change material (PCM). The numerical model is verified by the experimental data. The influences of different structures on the melting rate, temperature distribution, velocity distribution, and maximum melting rate of PCM in LHTES tank are investigated, and the influence of natural convection on the energy storage system is further quantified. The results show that the melting time can be significantly reduced by 16.9% by using the four straight fins with gradient shape, and the melting time can be further reduced by 41.1% by reconstruction of the gradient fin position. The deformation in the opposite direction will slow down the melting speed and extend the melting time by more than 4.66 times. The convection criterion for judging the buoyancy convection of the melt in this paper shows that natural convection is dominant in both the upper and lower part of the melt. The closer the convection coefficient is to the overall heat transfer coefficient, the better the melting efficiency and energy efficiency will be.
|
|
| 6. |
|
|
| 7. |
- Tu, Suo, et al.
(författare)
-
Improvement of the thermoelectric properties of PEDOT:PSS films via DMSO addition and DMSO/salt post-treatment resolved from a fundamental view
- 2022
-
Ingår i: Chemical Engineering Journal. - : Elsevier BV. - 1385-8947 .- 1873-3212. ; 429
-
Tidskriftsartikel (refereegranskat)abstract
- The combination of dimethyl sulfoxide (DMSO)-solvent doping and physical-chemical DMSO/salt de-doping in a sequence has been used to improve the thermoelectric (TE) properties of poly(3,4-ethylenedioxythiophene):poly (4-styrenesulfonate) (PEDOT:PSS) films. A high power factor of ca.105.2 mu W m(-1) K-2 has been achieved for the PEDOT:PSS film after post-treatment with 10 % sodium sulfite (Na2SO3) in the DMSO/salt mixture (v/v), outperforming sodium bicarbonate (NaHCO3). The initial DMSO-doping treatment induces a distinct phase separation by facilitating the aggregation of the PEDOT molecules. At the same time, the subsequent DMSO/salt dedoping post-treatment strengthens the selective removal of the surplus non-conductive PSS chains. Substantial alterations in the oxidation level, chain conformations, PEDOT crystallites and their preferential orientation are observed upon treatment on the molecular level. At the mesoscale level, the purification and densification of PEDOT-rich domains enable the realization of inter-grain coupling by the formation of the electronically well-percolated network. Thereby, both electrical conductivity and Seebeck coefficient are optimized.
|
|
| 8. |
- Yin, Shanshan, et al.
(författare)
-
Tailored fabrication of quasi-isoporous and double layered alpha-Fe2O3 thin films and their application in photovoltaic devices
- 2023
-
Ingår i: Chemical Engineering Journal. - : Elsevier BV. - 1385-8947 .- 1873-3212. ; 455, s. 140135-
-
Tidskriftsartikel (refereegranskat)abstract
- A series of α-Fe2O3 thin films with distinct morphologies are prepared via a facile polystyrene-block-polyethylene oxide templated sol–gel method. By tailoring the poor solvent contents and FeCl3-to-polymer weight ratio in the sol–gel solutions, quasi-isoporous α-Fe2O3 thin films with different substructures and thicknesses are obtained. Via a thermal annealing post-treatment, double layered structures are induced by a synergistic dewetting and Oswald ripening effect. Special focus is set on the α-Fe2O3 thin films prepared with no annealing/annealing-medium FeCl3 concentration, as they possess uniform periodic structures, which is suitable to be used as hole blocking modification layer of perovskite solar cells (PSCs). An improved power conversion efficiency (PCE) is obtained when the double layered α-Fe2O3 thin film is applied as the hole blocking modification layer for PSCs. The improved PCE primarily originates from the increased VOC, which probably benefits from the synergistic effect of the suppressed charge carrier recombination at the interfaces, the enhanced light transmittance as well as the superior electron extraction capacity.
|
|
