| 1. |
- Vult von Steyern, Fredrik, et al.
(författare)
-
All-ceramic fixed partial dentures designed according to the DC-Zirkon (R) technique. A 2-year clinical study
- 2005
-
Ingår i: Journal of Oral Rehabilitation. - : Wiley. - 0305-182X .- 1365-2842. ; 32:3, s. 180-187
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of the study was to investigate whether the properties of a pre-sintered, hot iso-static post-compacted ( HIP) ZrO2 are adequate for use in three-five-unit fixed partial dentures (FPDs) and to evaluate the clinical results. Twenty three five-unit FPDs were fabricated for 18 patients on a total of 56 abutments. They were all made on abutments cut with a shoulder preparation and cemented with a zinc phosphate cement. They were clinically followed for 24 months. After 24 months all FPDs were still in use without any fractures or clinical wear but in three cases (15%) minor chip-of fractures were observed. Marginal integrity was rated excellent at 45 abutments and acceptable at 11. Within the limitations of this 2-year clinical follow-up study, FPDs made of pre-sintered HIP ZrO2 core material veneered with a compatible ceramic is an acceptable alternative in the fabrication of FPDs with the extensions investigated in this study. Special attention, however, must be paid to designing the core for an occlusal shape that provides sufficient support for the veneer.
|
|
| 2. |
- Haag, Per, et al.
(författare)
-
15 Years of Clinical Experience with Procera® Alumina
- 2004
-
Ingår i: Applied Osseointegration Research. - 1651-0070. ; 4, s. 7-12
-
Forskningsöversikt (övrigt vetenskapligt/konstnärligt)abstract
- This paper reviews the long history and background development of technical, laboratory and clinical applications of Procera® technology for the fabrication of restorations on teeth and implants. Current clinical practice is considered and long-term results presented.
|
|
| 3. |
- Papia, Evaggelia, et al.
(författare)
-
Impaction-modified densely sintered yttria-stabilized tetragonal zirconium dioxide : methodology, surface structure, and bond strength
- 2012
-
Ingår i: Journal of Biomedical Materials Research. Part B - Applied biomaterials. - : John Wiley & Sons. - 1552-4973 .- 1552-4981. ; 100:3, s. 677-684
-
Tidskriftsartikel (refereegranskat)abstract
- The objectives of the study were to describe a novel method for producing zirconium dioxide specimens with a cementation surface that allows adhesive cementation techniques, to describe the surface structure and to evaluate the bond strength. Forty-eight pairs of specimens were fabricated and adhesively luted together. Three different surfaces were tested: impaction-modified surfaces created by using glass granules (G), impaction-modified surfaces created by using polymer granules (P) and a nonmodified control surface (C). Two bonding systems were used, Variolink(®)II (VA) or Panavia™F 2.0 (PA). During the different fabrication steps, the surfaces were examined under light microscope and analyzed with an optical interferometer. All groups were thermocycled and subjected to shear bond strength test. The groups with modified cementation surfaces showed significantly higher shear bond strength: 34.9 MPa (VA-G), 30.9 MPa (VA-P), 29.6 MPa (PA-P), and 26.1 MPa (PA-G) compared with the relevant control group: 20.5 MPa (VA-C) and 17.8 MPa (PA-C). The groups with surface modification showed a rougher surface structure and significantly fewer fractures between the cement and the zirconium dioxide surfaces compared to the control groups where all failures were adhesive. Impaction modification with an impaction medium pressed into the cementation surface of zirconium dioxide-based reconstructions can be used in combination with an additive production technique to increase bond strength. Both modification techniques described in the study result in a rougher surface structure and higher shear bond strength compared to the control groups.
|
|
| 4. |
- Vult von Steyern, Per, et al.
(författare)
-
Fracture strength of two oxide ceramic crown systems after cyclic pre-loading and thermocycling
- 2006
-
Ingår i: Journal of Oral Rehabilitation. - : Wiley. - 1365-2842 .- 0305-182X. ; 33:9, s. 682-689
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of the present study was to investigate the fracture resistance of zirconia crowns and to compare the results with crowns made of a material with known clinical performance (alumina) in away that reflects clinical aspects. Sixty crowns were made, 30 identical crowns of alumina and 30 of zirconia. Each group of 30 was randomly divided into three groups of 10 crowns that were to undergo different treatments: (i) water storage only, (ii) pre-loading (10 000 cycles, 30-300 N, 1 Hz), (iii) thermocycling (5-55 degrees , 5000 cycles) + pre-loading (10 000 cycles, 30-300 N, 1 Hz). Subsequently, all 60 crowns were subjected to load until fracture occurred. There were two types of fracture: total fracture and partial fracture. Fracture strengths (N) were: group 1, alumina 905/zirconia 975 (P = 0.38); group 2, alumina 904/zirconia 1108 (P < 0.007) and group 3, alumina 917/zirconia 910 (P > 0.05). Total fractures were more frequent in the alumina group (P < 0.01). Within the limitations of this in vitro study, it can be concluded that there is no difference in fracture strength between crowns made with zirconia cores compared with those made of alumina if they are subjected to load without any cyclic pre-load or thermocycling. There is, however, a significant difference (P = 0.01) in the fracture mode, suggesting that the zirconia core is stronger than the alumina core. Crowns made with zirconia cores have significantly higher fracture strengths after pre-loading.
|
|
| 5. |
- Vult von Steyern, Per, et al.
(författare)
-
Framställning av protetiska konstruktioner
- 2014
-
Ingår i: Tandläkartidningen. - 0039-6982. ; 106:2, s. 56-66
-
Tidskriftsartikel (övrigt vetenskapligt/konstnärligt)abstract
- I dag kan alla nödvändiga produktionssteg för framställning av dentala rekonstruktioner utföras med CAD/CAM-teknologi. CAD/CAM erbjuder goda förutsättningar för hög precision och bra materialhantering, men det gäller inte alla system. Endast välbeprövade och kliniskt testade material och tekniker bör därför användas för kliniskt bruk.
|
|
| 6. |
- Ambré, Marcus J, et al.
(författare)
-
Fracture strength of yttria-stabilized zirconium-dioxide (Y-TZP) fixed dental prostheses (FDPs) with different abutment core thicknesses and connector dimensions
- 2013
-
Ingår i: Journal of Prosthodontics. - : Wiley-Blackwell. - 1059-941X .- 1532-849X. ; 22:5, s. 377-382
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose: The aim of this study was to investigate the fracture strength and fracture mode of yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) posterior three-unit FDPs with varying connector dimension and abutment core thickness. Materials and Methods: Seventy 3-unit posterior FDP cores made of Y-TZP were divided into 7 groups with varying connector dimensions and abutment core thicknesses. All the FDPs underwent a simulated aging process including veneering, firing applications, thermocycling, and cyclic preloading. Finally the FDPs were subjected to load until fracture. Results: Significant difference was seen between the different subgroups (p < 0.05). Groups with the same connector dimension showed no significant difference in fracture strength. All fractures of the specimens involved the connector. Conclusions: Within the limitations of this in vitro study, it can be concluded that the strength of an all-ceramic Y-TZP FDP beam depends more on the connector dimension than on the thickness of the abutment core. Results indicate that the minimum abutment core thickness of an all-ceramic Y-TZP FDP might be reduced, compared to the recommended thickness, without reducing the strength of the reconstruction. This indication, however, needs to be verified by further studies before being considered generally applicable.
|
|
| 7. |
- Bahat, Zdravko, et al.
(författare)
-
Fracture strength of three-unit fixed partial denture cores (Y-TZP) with different connector dimension and design
- 2009
-
Ingår i: Swedish Dental Journal. - : Swedish dental association. - 0347-9994. ; 33:3, s. 149-159
-
Tidskriftsartikel (refereegranskat)abstract
- True crystalline ceramic materials presently used in restorative dentistry are Al2O3 (alumina) and yttrium-oxide stabilised tetragonal polycrystalline zirconium-dioxide (Y-TZP). To ensure optimal clinical performance, the dimensions of the Fixed Partial Denture (FPD) framework in general and of the connectors in particular, must be adequate. Considered recommendations for connector dimensions for Y-TZP FPDs vary from 2 to 4 mm in occluso-gingival height and 2 to 4 mm in bucco-lingual width. In order to reduce the fracture probability when designing all-ceramic FPDs, the shape of the connector is an important factor to consider. The radius of curvature at the gingival embrasure plays a significant role in the load-bearing capacity. FPDs with small gingival embrasure radii are subjected to high stress concentrations in the connector area during loading, compared to FPDs with large embrasure radii. The aim of this in-vitro study was to investigate how different radii of curvature in the embrasure of the connector area and different connector dimensions could affect the fracture resistance of 3-unit all-ceramic FPDs made of Y-TZP. Forty-eight FPDs in 6 groups of 8 FPDs with different connector design were produced in Procera Zirconia Bridge material. The FPD cores were subjected to heat treatment to simulate veneering. Following cementation, the FPDs were firstly thermocycled for 5,000 cycles, then preloaded for 10,000 cycles and finally loaded to fracture. All the FPDs fractured in the connector area. All the crack propagation which led to fracture started at the gingival embrasure of the connector. Within the limitations of this in-vitro study,the recommended minimum dimension of an anterior 3-unit all-ceramic FPD of Y-TZP is 3 mm in incisal-cervical direction and 2 mm in buccal-lingual direction. By increasing the radius of the gingival embrasure from 0.6 to 0.9 mm, the fracture strength for a Y-TZP FPD with connector dimension 3 x 3 mm increases by 20%.
|
|
| 8. |
- Bakitian, Fahad, et al.
(författare)
-
Effect of different semimonolithic designs on fracture resistance and fracture mode of translucent and high-translucent zirconia crowns
- 2018
-
Ingår i: Clinical, Cosmetic and Investigational Dentistry. - : Nakladatelstvi Lidove noviny. - 1179-1357. ; 10, s. 51-60
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose: The aim of this study was to describe different designs of semimonolithic crowns made of translucent and high-translucent zirconia materials and to evaluate the effect on fracture resistance and fracture mode. Methods: One hundred crowns with different designs were produced and divided into five groups (n=20): monolithic (M), partially veneered monolithic (semimonolithic) with 0.3 mm buccal veneer (SM0.3), semimonolithic with 0.5 mm buccal veneer (SM0.5), semimonolithic with 0.5 mm buccal veneer supported by wave design (SMW), and semimonolithic with 0.5 mm buccal veneer supported by occlusal cap design (SMC). Each group was divided into two subgroups (n=10) according to the materials used, translucent and high-translucent zirconia. All crowns underwent artificial aging before loading until fracture. Fracture mode analysis was performed. Fracture loads and fracture modes were analyzed using two-way ANOVA and Fisher’s exact probability tests (P≤0.05). Results: SM0.3 design showed highest fracture loads with no significant difference compared to M and SMW designs (P>0.05). SM0.5 design showed lower fracture loads compared to SMW and SWC designs. Crowns made of translucent zirconia showed higher fracture loads compared to those made of high-translucent zirconia. M, SM0.3, and all but one of the SMC crowns showed complete fractures with significant differences in fracture mode compared to SMW and SM0.5 crowns with cohesive veneer fractures (P≤0.05). Conclusion: Translucent and high-translucent zirconia crowns might be used in combination with 0.3 mm microcoating porcelain layer with semimonolithic design to enhance the esthetic properties of restorations without significantly decreasing fracture resistance of the crowns. If 0.5 mm porcelain layer is needed for a semimonolithic crown, wave design or cap design might be used to increase fracture resistance. In both cases, fracture resistance gained is likely to be clinically sufficient as the registered fracture loads were high in relation to expected loads under clinical use.
|
|
| 9. |
- Bakitian, Fahad, et al.
(författare)
-
Evaluation of Stress Distribution in Tooth-Supported Fixed Dental Prostheses Made of Translucent Zirconia with Variations in Framework Designs : A Three-Dimensional Finite Element Analysis
- 2020
-
Ingår i: Journal of Prosthodontics. - : John Wiley & Sons. - 1059-941X .- 1532-849X. ; 29:4, s. 315-322
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose To evaluate the influence of the framework designs on the stress distribution within tooth-supported partially veneered fixed dental prostheses (FDPs) made of translucent zirconia under simulated loads using a three-dimensional finite element analysis (3D-FEA). Material and Methods For a linear 3D-FEA, simplified 3D solid models of prepared abutment teeth (first premolar and first molar) with different 3-unit FDPs were created. The models with different FDP designs-monolithic zirconia (control); semi-monolithic zirconia with 0.3 mm veneer thickness (SM0.3); semi-monolithic zirconia with 0.5 mm veneer thickness (SM0.5); semi-monolithic zirconia with 0.5 mm veneer thickness supported with cap design (SMC), and semi-monolithic zirconia with 0.5 mm veneer thickness supported with wave design (SMW)-were analyzed using 3D-FEA. The elastic properties of the components (bone, dentine, cement, translucent zirconia, and veneering porcelain) were obtained from the published data for FEA. Simulated static loading forces (300 N) were applied at 10 degrees oblique direction over six points in the occlusal surfaces of the FDPs. Maximum principal stress, shear stress, and safety factor were calculated and analyzed among the different models. Results Semi-monolithic with cap design showed the smallest maximum principal stress levels in the veneering porcelain compared to all other models (SM0.3, SM0.5, SMW). The SM0.3 had lower maximum principal stress levels in the veneering porcelain compared to SM0.5. Regarding stresses in the zirconia framework, all models had comparable results in maximum principal tensile stresses, except SMW had a lower value. Maximum principal stress levels were located in the veneer component of SM0.3, SM0.5, and SMW, whereas, such levels were observed in the cervical areas of the zirconia frameworks of SMC and control. The SM0.3 had the highest maximum shear stress levels at the zirconia-veneer interface, while SMW had the lowest shear values. The 3D-FEA models with different FDP designs showed different minimum safety factor levels. Conclusions Framework and veneer designs play a significant role in the stress distribution of the partially veneered zirconia FDPs under loading. The FDPs with zirconia frameworks with cap design minimize the maximum principal tensile stress in the veneering porcelain. The FDPs with 0.3-mm-veneering porcelain show low maximum principal tensile stress in the veneering porcelain, but highest maximum shear stress at the zirconia-veneer interface. The FDPs with wave design of zirconia frameworks minimize the maximum shear stress considerably.
|
|
| 10. |
- Bakitian, Fahad, et al.
(författare)
-
Fracture strength of veneered translucent zirconium dioxide crowns with different porcelain thicknesses.
- 2017
-
Ingår i: Acta Biomaterialia Odontologica Scandinavica. - : Taylor & Francis. - 2333-7931. ; 3:1, s. 74-83
-
Tidskriftsartikel (refereegranskat)abstract
- Abstract Objective: To evaluate fracture strength of veneered translucent zirconium dioxide crowns designed with different porcelain layer thicknesses. Materials and Methods: Sixty crowns, divided into six groups of 10, were used in this study. Groups were divided according to different thicknesses of porcelain veneer on translucent zirconium dioxide cores of equal thickness (0.5 mm). Porcelain thicknesses were 2.5, 2.0, 1.0, 0.8, 0.5 and 0.3 mm. Crowns were artificially aged before loaded to fracture. Determination of fracture mode was performed using light microscope. Results: Group 1.0 mm showed significantly (p ≤ .05) highest fracture loads (mean 1540 N) in comparison with groups 2.5, 2.0 and 0.3 mm (mean 851, 910 and 1202 N). There was no significant difference (p>.05) in fracture loads among groups 1.0, 0.8 and 0.5 mm (mean 1540, 1313 and 1286 N). There were significantly (p ≤ .05) more complete fractures in group 0.3 mm compared to all other groups which presented mainly cohesive fractures. Conclusions: Translucent zirconium dioxide crowns can be veneered with minimal thickness layer of 0.5 mm porcelain without showing significantly reduced fracture strength compared to traditionally veneered (1.0–2.0 mm) crowns. Fracture strength of micro-veneered crowns with a layer of porcelain (0.3 mm) is lower than that of traditionally veneered crowns but still within range of what may be considered clinically sufficient. Porcelain layers of 2.0 mm or thicker should be used where expected loads are low only.
|
|
