| 1. |
- Chen, Yaqi, et al.
(författare)
-
Insight into the Extreme Side Reaction between LiNi0.5Co0.2Mn0.3O2 and Li1.3Al0.3Ti1.7(PO4)3 during Cosintering for All-Solid-State Batteries
- 2023
-
Ingår i: Chemistry of Materials. - 1520-5002 .- 0897-4756. ; 35:22, s. 9647-9656
-
Tidskriftsartikel (refereegranskat)abstract
- All-solid-sate batteries (ASSBs) with a NASICON-type solid-state electrolyte (SSE) of Li1.3Al0.3Ti1.7(PO4)3 (LATP) can be accepted as a promising candidate to significantly improve safety and energy density due to their high oxidation potential and high ionic conductivity. However, thermodynamic instability between the cathode and LATP is scarcely investigated during cosintering preparation for the integrated configuration of ASSBs. Herein, the structural compatibility between commercially layered LiNi0.5Co0.2Mn0.3O2 (NCM523) and LATP SSE was systematically investigated by cosintering at 600 °C. It is noticeable that an extreme side reaction between Li from NCM523 and phosphate from LATP happens during its cosintering process, leading to a severe phase transition from a layered to a spinel structure with high Li/Ni mixing. Consequently, the capacity of NCM523 is lost during the preparation of the NCM523-LATP composite cathode. Based on this, we suggested that the interface modification of the NCM523/LATP interface is valued significantly to inhibit this extreme side reaction, quickening the application of LATP-based ASSBs.
|
|
| 2. |
- Jiao, Xingxing, et al.
(författare)
-
Insight of electro-chemo-mechanical process inside integrated configuration of composite cathode for solid-state batteries
- 2023
-
Ingår i: Energy Storage Materials. - 2405-8297. ; 61
-
Tidskriftsartikel (refereegranskat)abstract
- The complicated electro-chemo-mechanical process that occurs inside the composite cathode for solid-state batteries (SSBs), is of first importance to be insighted for the development of SSBs to seek higher energy density. Herein, exampled with layered transition-metal oxide of LiNixCoyMn1-x-yO2 (NCM), an electro-chemo-mechanical model containing electrochemical kinetics, finite-strain constitutive model and cohesive zone model was built to uncover the impact of ionic conductivity and Young's modulus (E) of solid-state electrolyte (SE) on the electro-chemo-mechanical process inside composite cathode and the intergranular failure of single cathode particle. The intergranular failure of NCM particles is powerfully determined by the Young's modulus of SE and the primary particle size, which is postponed by the coarse-primary NCM with soft SE of E=∼2 GPa. Compared with Young's modulus, increasing the ionic conductivity can uniform the distribution of both Li-ion and stress in the whole composite NCM cathode, realizing improved electrochemical performance with larger normalized capacity and lower the interfacial impendence. Hence, high-adequate ionic conductivity of 5 × 10−4 S cm−1 and soft mechanical property of E=∼2 GPa can be proposed as the guideline of SE for great electrochemical performance with prolongated lifespan of composite NCM cathode, paving an avenue to foster the application of SSBs.
|
|
| 3. |
- Jiao, Xingxing, et al.
(författare)
-
Multi-Physical Field Simulation: A Powerful Tool for Accelerating Exploration of High-Energy-Density Rechargeable Lithium Batteries
- 2023
-
Ingår i: Advanced Energy Materials. - 1614-6840 .- 1614-6832. ; In Press
-
Forskningsöversikt (refereegranskat)abstract
- To meet the booming demand of high-energy-density battery systems for modern power applications, various prototypes of rechargeable batteries, especially lithium metal batteries with ultrahigh theoretical capacity, have been intensively explored, which are intimated with new chemistries, novel materials and rationally designed configurations. What happens inside the batteries is associated with the interaction of multi-physical field, rather than the result of the evolution of a single physical field, such as concentration field, electric field, stress field, morphological evolution, etc. In this review, multi-physical field simulation with a relatively wide length and timescale is focused as formidable tool to deepen the insight of electrodeposition mechanism of Li metal and the electro-chemo-mechanical failure of solid-state electrolytes based on Butler-Volmer electrochemical kinetics and solid mechanics, which can promote the future development of state-of-the-art Li metal batteries with satisfied energy density as well as lifespan.
|
|
| 4. |
- Jiao, Xingxing, et al.
(författare)
-
Viability of all-solid-state lithium metal battery coupled with oxide solid-state electrolyte and high-capacity cathode
- 2024
-
Ingår i: Journal of Energy Chemistry. - 2095-4956. ; 91, s. 122-131
-
Tidskriftsartikel (refereegranskat)abstract
- Owing to the utilization of lithium metal as anode with the ultrahigh theoretical capacity density of 3860 mA h g−1 and oxide-based ceramic solid-state electrolytes (SE), e.g., garnet-type Li7La3Zr2O12 (LLZO), all-state-state lithium metal batteries (ASLMBs) have been widely accepted as the promising alternatives for providing the satisfactory energy density and safety. However, its applications are still challenged by plenty of technical and scientific issues. In this contribution, the co-sintering temperature at 500 °C is proved as a compromise method to fabricate the composite cathode with structural integrity and declined capacity fading of LiNi0.5Co0.2Mn0.3O2 (NCM). On the other hand, it tends to form weaker grain boundary (GB) inside polycrystalline LLZO at inadequate sintering temperature for LLZO, which can induce the intergranular failure of SE during the growth of Li filament inside the unavoidable defect on the interface of SE. Therefore, increasing the strength of GB, refining the grain to 0.4 μm, and precluding the interfacial defect are suggested to postpone the electro-chemo-mechanical failure of SE with weak GB. Moreover, the advanced sintering techniques to lower the co-sintering temperature for both NCM-LLZO composite cathode and LLZO SE can be posted out to realize the viability of state-of-the-art ASLMBs with higher energy density as well as the guaranteed safety.
|
|
| 5. |
- Su, Changqing, et al.
(författare)
-
Gene-Viral Cancer Therapy Using Dual-Regulated Oncolytic Adenovirus with Antiangiogenesis Gene for Increased Efficacy.
- 2008
-
Ingår i: Molecular Cancer Research. - 1557-3125. ; 6, s. 568-575
-
Tidskriftsartikel (refereegranskat)abstract
- Conditionally replicative adenovirus (CRAD) represents a promising approach for cancer therapy. Several CRADs controlled by the human telomerase reverse transcriptase promoter have been developed. However, because of their replicative capacity, the importance of cancer specificity for CRADs needs to be further emphasized. In this study, we have developed a novel dual-regulated CRAD, CNHK500-mE, which has its E1a and E1b gene controlled by the human telomerase reverse transcriptase promoter and the hypoxia response element, respectively. It also carries a mouse endostatin expression cassette controlled by the cytomegalovirus promoter. These properties allow for increased cancer cell targeting specificity and decreased adverse side effects. We showed that CNHK500-mE preferentially replicated in cancer cells. Compared with a replication-defective vector carrying the same endostatin expression cassette, CNHK500-mE-mediated transgene expression level was markedly increased via viral replication within cancer cells. In the nasopharyngeal tumor xenograft model, CNHK500-mE injection resulted in antitumor efficacy at day 7 after therapy. Three weeks later, it led to significant inhibition of xenograft tumor growth due to the combined effects of viral oncolytic therapy and antiangiogenesis gene therapy. Pathologic examination showed that most cancer cells were positive for adenoviral capsid protein and for apoptotic terminal deoxynucleotidyl transferase-mediated dUTP nick end labeling in the CNHK500-mE-treated tumor tissues, and the microvessels in these tumor tissues were diminished in quantity and abnormal in morphology. These results suggest that, as a potential cancer therapeutic agent, the CNHK500-mE is endowed with higher specificity to cancer cells and low cytotoxicity to normal cells. (Mol Cancer Res 2008;6(4):OF1-8).
|
|
| 6. |
- Bai, Ru, et al.
(författare)
-
The NF-κB-modulated miR-19a-3p enhances malignancy of human ovarian cancer cells through inhibition of IGFBP-3 expression
- 2019
-
Ingår i: Molecular Carcinogenesis. - : Wiley. - 0899-1987 .- 1098-2744. ; 58:12, s. 2254-2265
-
Tidskriftsartikel (refereegranskat)abstract
- Ovarian cancer is the most lethal gynecologic malignancy due to the lack of symptoms until advanced stages, and new diagnosis and treatment strategy is in urgent need. In this study, we found higher expression of miR-19a-3p in ovarian cancer tissues compared with that in the adjacent normal tissues. By chromatin immunoprecipitation (ChIP) and electrophoretic mobility shift assay (EMSA) analysis, we showed that nuclear factor-kappaB (NF-κB) binds to the promoter of miR-19a-3p, leading to reduced expression in ovarian cancer cells. Further study indicated that miR-19a-3p inhibits the expression of insulin-like growth factor binding protein-3 (IGFBP-3), resulting in enhanced growth and migration of ovarian cancer cells in vitro and tumor growth in vivo. These results showed that miR-19a-3p enhances the oncogenesis of ovarian cancer through inhibition of IGFBP-3 expression, and which can be inhibited by NF-κB, suggesting an NF-κB/miR-19a-3p/IGFBP-3 pathway in the oncogenesis of ovarian cancer, which expands our understanding of ovarian cancer and they may contribute to the development of new diagnosis and treatment of ovarian cancer.
|
|
| 7. |
- Jiao, Xingxing, et al.
(författare)
-
Electro-chemo-mechanical failure of solid-state electrolyte caused from intergranular or transgranular damage propagation in polycrystalline aggregates
- 2024
-
Ingår i: Acta Materialia. - 1359-6454. ; 265
-
Tidskriftsartikel (refereegranskat)abstract
- Electro-chemo-mechanical failure of solid-state electrolytes (SEs) caused by the internal growth of lithium dendrites significantly impedes the application of solid-state batteries under high applied current density. The grain boundary is usually the key to the mechanical properties of polycrystalline ceramic SEs. Here, strength and width of grain boundary in SEs that are exampled by garnet-type Li7La3Zr2O12 are evaluated under the deposition of lithium by visualizing the stress field, damage accumulation and crack propagation. The enhancement of grain boundary strength triggers a dramatic increase stress when the ratio of tensile strength between grain boundary and grain (λ) is lower than 0.9. With the variation of λ, three damage processes are revealed as intergranular-damage, inter/transgranular-damage and transgranular-damage, leading to different propagation of cracks and the transformation of intergranular failure to transgranular failure. Furthermore, the width of the grain boundary is found to induce more transgranular-damage with its widening. A critical value of grain boundary width for the formation of displacement is obtained under various strengths, as δ = 21 nm for λ = 0.2, δ = 25 nm for λ = 0.5 and δ = 31 nm for λ = 0.9. The findings in this work indicate the coupling effect of grain boundary width and strength on the failure of SEs, providing an insightful perspective for the future design of solid-state batteries.
|
|
| 8. |
- Jiao, Xingxing, et al.
(författare)
-
Grain size and grain boundary strength: Dominative role in electro-chemo-mechanical failure of polycrystalline solid-state electrolytes
- 2024
-
Ingår i: Energy Storage Materials. - 2405-8297. ; 65
-
Tidskriftsartikel (refereegranskat)abstract
- Solid-state batteries with lithium metal anode have been accepted extensively as the competitive option to fulfill the upping requirement for safe and efficient energy devices. Nevertheless, its wide-ranging application has been impeded by the failure of solid-state electrolyte (SSE) induced by development of lithium (Li) filament. Based on the nature of polycrystalline ceramic SSE with varying grain size and boundary strength, the constitutive equation coupled with electrochemical kinetics was applied to picture the propagation of damage and corresponding disintegration caused by the development of Li filament. Based on the results, we found that the stress generated along with the growth of Li filament spreads away via the opening and sliding of grain boundary. Thus, damage occurs along grain boundaries, of which propagation behavior and damage level are controlled by grain size. Especially, over-refinement and under-refinement of grains of SSE can cause flocculent damage with inordinate damage degree and accelerate the failure time of SSE, respectively. On the other hand, the failure time is powerfully prolongated through strengthening the grain boundary of SSE. Eventually, grain size of 0.2 μm and tensile strength of grain boundary of 0.8-time-of-grain are posted as the threshold to realize the postponed failure of NASICON-based SSE. Inspiringly, electro-chemo-mechanical model in this contribution is generally applicable to other type of ceramic SSE to reveal the failure process and provide the design guideline, fostering the improvement of solid-state batteries.
|
|
| 9. |
- Jiao, Xingxing, et al.
(författare)
-
Morphology evolution of electrodeposited lithium on metal substrates
- 2023
-
Ingår i: Energy Storage Materials. - 2405-8297. ; 61
-
Tidskriftsartikel (refereegranskat)abstract
- Lithium (Li) metal is deemed to be the high-energy-density anode material for next generation batteries, but its practical application is impeded by the uneven electrodeposition during charge of battery, which leads to the low Coulombic efficiency and potential safety issue. Here, multiscale modeling is fabricated to understand the morphology evolution of Li during electrodeposition process, from the self-diffusion of Li adatoms on electrode surface, to the nucleation process, and to the formation of Li microstructures, revealing the correlation between final morphology and deposition substrates. Energy batteries and self-diffusion of Li adatom on various substrates (lithium, copper, nickel, magnesium, and silver) result in the different nucleation size, which is calculated by kinetic Monte Carlo simulation based on classical nucleation theory. Formation of Li substructures that are grown from Li nuclei, is revealed by phase field modeling coupled with cellular automaton method. Our results show that larger Li nuclei is obtained under faster self-diffusion of Li adatom, leading to the low aspect ratio of Li substructures and the subsequent morphology evolution of electrodeposited Li. Furthermore, the electrodeposition of Li is strongly regulated by the selection of substrates, giving the practical guideline of anode design in rechargeable Li metal batteries. It is worthy to mention that this method to investigate the electro-crystallization process involving nucleation and growth can be transplanted to the other metallic anode, such as sodium, potassium, zinc, magnesium, calcium and the like.
|
|
| 10. |
- Xiong, Shizhao, 1985, et al.
(författare)
-
Mechanical Failure of Solid-State Electrolyte Rooted in Synergy of Interfacial and Internal Defects
- 2023
-
Ingår i: Advanced Energy Materials. - : Wiley. - 1614-6840 .- 1614-6832. ; 13:14
-
Tidskriftsartikel (refereegranskat)abstract
- The mechanical failure of solid-state electrolytes induced by the growth of the lithium metal anode hinders the development of solid-state Li metal batteries with good safety and high energy density, and thus the understanding of the failure mechanism is of high importance for the application of solid-state lithium-metal batteries. Herein, a modified electro-chemo-mechanical model is built to bridge the dynamic relationship between the mechanical failure of solid-state electrolytes and the electrodeposition of lithium metal. The results, visualize evolution of local stress fields and the corresponding relative damage, and indicate that the generation of damage inside the solid-state electrolyte is rooted in a synergy of interfacial and internal defects. Compression by electrodeposited lithium inside interfacial defects and further transmission of stress inward in the electrolyte causes catastrophic damage, which is determined by the geometry of interfacial defects. Moreover, the internal defects of the solid-state electrolyte from sintering can influence the pathway of damage and work as the inner fountainhead for further damage propagation, and as such, the position and amount of the internal voids exhibit a more competitive role in the mechanical failure of solid-state electrolyte. Thus, the synergetic failure mechanism of solid-state electrolytes raised in this work provides a modeling framework to design effective strategies for state-of-the-art solid-state lithium-metal batteries.
|
|
