| 1. |
- Beal, Jacob, et al.
(författare)
-
Robust estimation of bacterial cell count from optical density
- 2020
-
Ingår i: Communications Biology. - : Springer Science and Business Media LLC. - 2399-3642. ; 3:1
-
Tidskriftsartikel (refereegranskat)abstract
- Optical density (OD) is widely used to estimate the density of cells in liquid culture, but cannot be compared between instruments without a standardized calibration protocol and is challenging to relate to actual cell count. We address this with an interlaboratory study comparing three simple, low-cost, and highly accessible OD calibration protocols across 244 laboratories, applied to eight strains of constitutive GFP-expressing E. coli. Based on our results, we recommend calibrating OD to estimated cell count using serial dilution of silica microspheres, which produces highly precise calibration (95.5% of residuals <1.2-fold), is easily assessed for quality control, also assesses instrument effective linear range, and can be combined with fluorescence calibration to obtain units of Molecules of Equivalent Fluorescein (MEFL) per cell, allowing direct comparison and data fusion with flow cytometry measurements: in our study, fluorescence per cell measurements showed only a 1.07-fold mean difference between plate reader and flow cytometry data.
|
|
| 2. |
- Hong, Wang, et al.
(författare)
-
Safety Decision of Running Speed Based on Real-time Weather
- 2022
-
Ingår i: 2022 IEEE intelligent vehicles symposium (IV). - : Institute of Electrical and Electronics Engineers (IEEE). ; , s. 212-217
-
Konferensbidrag (refereegranskat)abstract
- The safety of autonomous vehicles is hard to ensure in adverse weather since the sensors will degrade drastically. Setting a variable speed limit based on real-time weather condition is the most efficient method to make the vehicle safe. But most current speed limit methods are based on human visibility rather than the sensor, which is not suitable for autonomous vehicles. Thus, it is necessary to explore the performance of sensors in different weathers and propose a speed limit method based on sensor performance. Safety decisions will be made based on the calculated speed limit to ensure safety. This paper describes how to make safety decisions based on sensor performance and road conditions in real-time. The experiment explores the degradation of different sensors, and variable speed limit methods are proposed for rainy and foggy days. MPC controller is used to generate safety decisions.
|
|
| 3. |
- Liu, Alei, et al.
(författare)
-
Manipulate Micrometer Surface and Nanometer Bulk Phase Separation Structures in the Active Layer of Organic Solar Cells via Synergy of Ultrasonic and High-Pressure Gas Spraying
- 2019
-
Ingår i: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 11:11, s. 10777-10784
-
Tidskriftsartikel (refereegranskat)abstract
- For organic solar cells, the vertical and lateral micro-/nanometer-scale structure in the active layer largely determines the device performance. In this work, the surface and bulk domain size of the photoactive layer are successfully manipulated with a facile two-step spraying method, that is, an ultrathin active layer by high-pressure spraying is deliberately stacked on top of the thick active layer by ultrasonic spraying. Thus, the morphology is effectively optimized with the comprehensive study of optical and electrical characteristics, such as photon absorption, exciton dissociation efficiency, and bimolecular recombination. Moreover, the novel method can be used not only in the fullerene system but also in the nonfullerene system, demonstrating the remarkable universality through this synergy method. This work provides an easy and reliable strategy to improve photovoltaic device performance in the industrial large-area spray-coating process.
|
|
| 4. |
- van Es, Michael A, et al.
(författare)
-
Angiogenin variants in Parkinson disease and amyotrophic lateral sclerosis
- 2011
-
Ingår i: Annals of Neurology. - : Wiley-Blackwell. - 0364-5134 .- 1531-8249. ; 70:6, s. 964-973
-
Tidskriftsartikel (refereegranskat)abstract
- OBJECTIVE: Several studies have suggested an increased frequency of variants in the gene encoding angiogenin (ANG) in patients with amyotrophic lateral sclerosis (ALS). Interestingly, a few ALS patients carrying ANG variants also showed signs of Parkinson disease (PD). Furthermore, relatives of ALS patients have an increased risk to develop PD, and the prevalence of concomitant motor neuron disease in PD is higher than expected based on chance occurrence. We therefore investigated whether ANG variants could predispose to both ALS and PD.METHODS: We reviewed all previous studies on ANG in ALS and performed sequence experiments on additional samples, which allowed us to analyze data from 6,471 ALS patients and 7,668 controls from 15 centers (13 from Europe and 2 from the USA). We sequenced DNA samples from 3,146 PD patients from 6 centers (5 from Europe and 1 from the USA). Statistical analysis was performed using the variable threshold test, and the Mantel-Haenszel procedure was used to estimate odds ratios.RESULTS: Analysis of sequence data from 17,258 individuals demonstrated a significantly higher frequency of ANG variants in both ALS and PD patients compared to control subjects (p = 9.3 × 10(-6) for ALS and p = 4.3 × 10(-5) for PD). The odds ratio for any ANG variant in patients versus controls was 9.2 for ALS and 6.7 for PD.INTERPRETATION: The data from this multicenter study demonstrate that there is a strong association between PD, ALS, and ANG variants. ANG is a genetic link between ALS and PD.
|
|
| 5. |
- Yang, Junyu, et al.
(författare)
-
Roll-to-Roll Slot-Die-Printed Polymer Solar Cells by Self-Assembly
- 2018
-
Ingår i: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 10:26, s. 22485-22494
-
Tidskriftsartikel (refereegranskat)abstract
- Extremely simplified one-step roll-to-roll slot-die-printed flexible indium tin oxide (ITO)-free polymer solar cells (PSCs) are demonstrated based on the ternary blends of electron-donor polymer thieno[3,4-b]thiophene/benzodithiophene, electron-acceptor fullerene [6,6]-phenyl-C-71-butyric acid methyl ester, and electron-extracting polymer poly[(9,9-bis(3-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) at room temperature (RT) in ambient air. The flexible ITO-free PSC exhibits a comparable power conversion efficiency (PCE) with the device employing complicated two-step slot-die printing (5.29% vs 5.41%), which indicates that PFN molecules can migrate from the ternary nanocomposite toward the Ag cathode via vertical self-assembly during the one-step slot-die printing process in air. To confirm the migration of PFN, the morphology and elemental analysis as well as charge transport of different active layers are investigated by the in situ transient film drying process, transmission electron microscopy, atomic force microscopy, contact angle and surface energy, X-ray photoelectron spectroscopy, scanning electron microscopy, impedance spectroscopy, transient photovoltage and transient photocurrent, and laser-beam-induced current. Moreover, the good air and mechanical stability of the flexible device with a decent PCE achieved in 1 cm(2) PSCs at RT in air suggests the feasibility of energy-saving and time-saving one-step slot-die printing to large-scale roll-to-roll manufacture in the future.
|
|
