| 1. |
- Sveinbjörnsson, Kári, et al.
(författare)
-
Ambient air-processed mixed-ion perovskites for high-efficiency solar cells
- 2016
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 4:42, s. 16536-16545
-
Tidskriftsartikel (refereegranskat)abstract
- Mixed-ion (FAPbI(3))(1-x)(MAPbBr(3))(x) perovskite solar cells have achieved power conversion efficiencies surpassing 20%. However, in order to obtain these high efficiencies the preparation is performed in a controlled inert atmosphere. Here, we report a procedure for manufacturing highly efficient solar cells with a mixed-ion perovskite in ambient atmosphere. By including a heating step at moderate temperatures of the mesoporous titanium dioxide substrates, and spin-coating the perovskite solution on the warm substrates in ambient air, a red intermediate phase is obtained. Annealing the red phase at 100 degrees C results in a uniform and crystalline perovskite film, whose thickness is dependent on the substrate temperature prior to spin-coating. The temperature was optimized between 20 and 100 degrees C and it was observed that 50 degrees C substrate temperature yielded the best solar cell performances. The average efficiency of the best device was 17.6%, accounting for current-voltage (I-V) measurement hysteresis, with 18.8% performance in the backward scan direction and 16.4% in the forward scan direction. Our results show that it is possible to manufacture high-efficiency mixed-ion perovskite solar cells under ambient conditions, which is relevant for large-scale and low-cost device manufacturing processing.
|
|
| 2. |
- Wang, Linqin, et al.
(författare)
-
Design and synthesis of dopant-free organic hole-transport materials for perovskite solar cells
- 2018
-
Ingår i: Chemical Communications. - : ROYAL SOC CHEMISTRY. - 1359-7345 .- 1364-548X. ; 54:69, s. 9571-9574
-
Tidskriftsartikel (refereegranskat)abstract
- Two novel dopant-free hole-transport materials (HTMs) with spiro[dibenzo[c,h]xanthene-7,9-fluorene] (SDBXF) skeletons were prepared via facile synthesis routes. A power conversion efficiency of 15.9% in perovskite solar cells is attained by using one HTM without dopants, which is much higher than undoped Spiro-OMeTAD-based devices (10.8%). The crystal structures of both new HTMs were systematically investigated to reveal the reasons behind such differences in performance and to indicate the design principles of more advanced HTMs.
|
|
| 3. |
- Xu, Bo, et al.
(författare)
-
Integrated Design of Organic Hole Transport Materials for Efficient Solid-State Dye-Sensitized Solar Cells
- 2015
-
Ingår i: Advanced Energy Materials. - : Wiley. - 1614-6832 .- 1614-6840. ; 5:3
-
Tidskriftsartikel (refereegranskat)abstract
- A series of triphenylamine-based small molecule organic hole transport materials (HTMs) with low crystallinity and high hole mobility are systematically investigated in solid-state dye-sensitized solar cells (ssDSCs). By using the organic dye LEG4 as a photosensitizer, devices with X3 and X35 as the HTMs exhibit desirable power conversion efficiencies (PCEs) of 5.8% and 5.5%, respectively. These values are slightly higher than the PCE of 5.4% obtained by using the state-of-the-art HTM Spiro-OMeTAD. Meanwhile, transient photovoltage decay measurement is used to gain insight into the complex influences of the HTMs on the performance of devices. The results demonstrate that smaller HTMs induce faster electron recombination in the devices and suggest that the size of a HTM plays a crucial role in device performance, which is reported for the first time.
|
|
| 4. |
- Zhang, Jinbao, et al.
(författare)
-
Al2O3 Underlayer Prepared by Atomic Layer Deposition for Efficient Perovskite Solar Cells.
- 2017
-
Ingår i: ChemSusChem. - : Wiley. - 1864-5631 .- 1864-564X. ; 10:19, s. 3810-3817
-
Tidskriftsartikel (refereegranskat)abstract
- Perovskite solar cells, as an emergent technology for solar energy conversion, have attracted much attention in the solar cell community by demonstrating impressive enhancement in power conversion efficiencies. However, the high temperature and manually processed TiO2 underlayer prepared by spray pyrolysis significantly limit the large-scale application and device reproducibility of perovskite solar cells. In this study, lowtemperature atomic layer deposition (ALD) is used to prepare a compact Al2 O3 underlayer for perovskite solar cells. The thickness of the Al2 O3 layer can be controlled well by adjusting the deposition cycles during the ALD process. An optimal Al2 O3 layer effectively blocks electron recombination at the perovskite/fluorine-doped tin oxide interface and sufficiently transports electrons through tunneling. Perovskite solar cells fabricated with an Al2 O3 layer demonstrated a highest efficiency of 16.2 % for the sample with 50 ALD cycles (ca. 5 nm), which is a significant improvement over underlayer-free PSCs, which have a maximum efficiency of 11.0 %. Detailed characterization confirms that the thickness of the Al2 O3 underlayer significantly influences the charge transfer resistance and electron recombination processes in the devices. Furthermore, this work shows the feasibility of using a high band-gap semiconductor such as Al2 O3 as the underlayer in perovskite solar cells and opens up pathways to use ALD Al2 O3 underlayers for flexible solar cells.
|
|
| 5. |
- Zhang, Jinbao, et al.
(författare)
-
Chemical Dopant Engineering in Hole Transport Layers for Efficient Perovskite Solar Cells : Insight into the Interfacial Recombination
- 2018
-
Ingår i: ACS Nano. - : American Chemical Society (ACS). - 1936-0851 .- 1936-086X. ; 12:10, s. 10452-10462
-
Tidskriftsartikel (refereegranskat)abstract
- Chemical doping of organic semiconductors has been recognized as an effective way to enhance the electrical conductivity. In perovskite solar cells (PSCs), various types of dopants have been developed for organic hole transport materials (HTMs); however, the knowledge of the basic requirements for being efficient dopants as well as the comprehensive roles of the dopants in PSCs has not been clearly revealed. Here, three copper-based complexes with controlled redox activities are applied as dopants in PSCs, and it is found that the oxidative reactivity of dopants presents substantial impacts on conductivity, charge dynamics, and solar cell performance. A significant improvement of open- circuit voltage (V-oc) by more than 100 mV and an increase of power conversion efficiency from 13.2 to 19.3% have been achieved by tuning the doping level of the HTM. The observed large variation of V-oc for three dopants reveals their different recombination kinetics at the perovskite/HTM interfaces and suggests a model of an interfacial recombination mechanism. We also suggest that the dopants in HTMs can also affect the charge recombination kinetics as well as the solar cell performance. Based on these findings, a strategy is proposed to physically passivate the electron- hole recombination by inserting an ultrathin Al2O3 insulating layer between the perovskite and the HTM. This strategy contributes a significant enhancement of the power conversion efficiency and environmental stability, indicating that dopant engineering is one crucial way to further improve the performance of PSCs.
|
|
| 6. |
- Zhang, Jinbao, et al.
(författare)
-
Efficient solid-state dye sensitized solar cells : The influence of dye molecular structures for the in-situ photoelectrochemically polymerized PEDOT as hole transporting material
- 2016
-
Ingår i: NANO ENERGY. - : Elsevier BV. - 2211-2855. ; 19, s. 455-470
-
Tidskriftsartikel (refereegranskat)abstract
- Solid-state dye sensitized solar cells (sDSCs) with organic small molecule hole transporting materials (HTMs) have limited efficiencies due to the incomplete pore filling of the HTMs in the thick mesoporous electrodes and the low hole conductivity of HTMs. Hereby, highly efficient sDSCs with power conversion efficiency of 7.11% and record photocurrent of 13.4 mA cm-2 are reported, prepared by effectively incorporating in-situ photoelectrochemically polymerized PEDOT as HTM in combination with a multifunctional organic, metal-free dye. In order to fundamentally understand how the dye molecules affect the photoelectrochemical polymerization (PEP), the properties of the generated PEDOT and the photovoltaic performance, sDSCs based on a series of dyes are systematically investigated. Detailed comparative studies reveal that the difference between the dye redox potential and monomer onset oxidation potential plays a crucial role in the PEP kinetics and the doping density of PEDOT HTM. The structure of the dyes, functioning as an electron blocking layer, affects the charge recombination at the TiO2/dye/PEDOT interface. The analysis shows that a donor-n-acceptor dye with well-tuned energy levels and bulky structure results in an in-situ electrochemically doped PEDOT HTM with a high hole conductivity (2.0 S cm(-1)) in sDSCs, leading to efficient dye regeneration and photocharge collection. It is hoped that this work will further encourage research on the future design of new dye molecules for an efficient PEP in order to further enhance the photovoltaic performance of solid-state dye sensitized solar cells.
|
|
| 7. |
- Zhang, Jinbao, et al.
(författare)
-
The Importance of Pendant Groups on Triphenylamine-Based Hole Transport Materials for Obtaining Perovskite Solar Cells with over 20% Efficiency
- 2018
-
Ingår i: Advanced Energy Materials. - : Wiley. - 1614-6832 .- 1614-6840. ; 18:2
-
Tidskriftsartikel (refereegranskat)abstract
- Tremendous progress has recently been achieved in the field of perovskite solar cells (PSCs) as evidenced by impressive power conversion efficiencies (PCEs); but the high PCEs of >20% in PSCs has so far been mostly achieved by using the hole transport material (HTM) spiro-OMeTAD; however, the relatively low conductivity and high cost of spiro-OMeTAD significantly limit its potential use in large-scale applications. In this work, two new organic molecules with spiro[fluorene-9,9-xanthene] (SFX)-based pendant groups, X26 and X36, have been developed as HTMs. Both X26 and X36 present facile syntheses with high yields. It is found that the introduced SFX pendant groups in triphenylamine-based molecules show significant influence on the conductivity, energy levels, and thin-film surface morphology. The use of X26 as HTM in PSCs yields a remarkable PCE of 20.2%. In addition, the X26-based devices show impressive stability maintaining a high PCE of 18.8% after 5 months of aging in controlled (20%) humidity in the dark. We believe that X26 with high device PCEs of >20% and simple synthesis show a great promise for future application in PSCs, and that it represents a useful design platform for designing new charge transport materials for optoelectronic applications.
|
|
| 8. |
- Zhang, Xiaoli, et al.
(författare)
-
All-Inorganic Perovskite Nanocrystals for High-Efficiency Light Emitting Diodes : Dual-Phase CsPbBr3-CsPb2Br5 Composites
- 2016
-
Ingår i: Advanced Functional Materials. - : Wiley. - 1616-301X .- 1616-3028. ; 26:25, s. 4595-4600
-
Tidskriftsartikel (refereegranskat)abstract
- A dual-phase all-inorganic composite CsPbBr3-CsPb2Br5 is developed and applied as the emitting layer in LEDs, which exhibited a maximum luminance of 3853 cd m(-2), with current density (CE) of approximate to 8.98 cd A(-1) and external quantum efficiency (EQE) of approximate to 2.21%, respectively. The parasite of secondary phase CsPb2Br5 nanoparticles on the cubic CsPbBr3 nanocrystals could enhance the current efficiency by reducing diffusion length of excitons on one side, and decrease the trap density in the band gap on the other side. In addition, the introduction of CsPb2Br5 nanoparticles could increase the ionic conductivity by reducing the barrier against the electronic and ionic transport, and improve emission lifetime by decreasing nonradiative energy transfer to the trap states via controlling the trap density. The dual-phase all-inorganic CsPbBr3-CsPb2Br5 composite nanocrystals present a new route of perovskite material for advanced light emission applications.
|
|
| 9. |
- Zhang, Xiaoli, et al.
(författare)
-
Codoping-Induced, Rhombus-Shaped Co3O4 Nanosheets as an Active Electrode Material for Oxygen Evolution
- 2015
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 7:39, s. 21745-21750
-
Tidskriftsartikel (refereegranskat)abstract
- Nanostructured Co3O4 doped with Zn2+, Ni2+, and both were directly grown on an ITO substrate by an easily available hydrothermal method. The doped Co3O4 showed a unique structural morphology evolution upon controlling the doping elements and the doping ratio of the cations. For the codoped samples, the novel rhombus-shaped Co3O4 nanosheets doped with Zn2+ and Ni2+ (concentration ratio of 1:2) exhibited the optimal electrocatalytic performance. The sample showed a current density of 165 mA cm(-2) at 1.75 V, approximately 1.6 and 4 times higher than that of samples doped with Zn2+ and Ni2+ at a concentration ratio of 1:1 and 1:3. The unique architecture and its corresponding modified physical properties, such as high active-site density created by codoping, large structural porosity, and high roughness, are together responsible to its superior performance. For codoped Co3O4 nanostructures, Zn2+ facilitates the creation of Co cations in their high oxidation state as active centers, while Ni2+ contributed to the new active sites with lower activation energy. The synergistic effect of Zn2+ and Ni2+ doping can explain the improved physicochemical properties of codoped Co3O4 nanostructures.
|
|
| 10. |
- Zhang, Xiaoli, et al.
(författare)
-
Hybrid Perovskite Light-Emitting Diodes Based on Perovskite Nanocrystals with Organic-Inorganic Mixed Cations
- 2017
-
Ingår i: Advanced Materials. - : WILEY-V C H VERLAG GMBH. - 0935-9648 .- 1521-4095. ; 29:18
-
Tidskriftsartikel (refereegranskat)abstract
- Organic-inorganic hybrid perovskite materials with mixed cations have demonstrated tremendous advances in photovoltaics recently, by showing a significant enhancement of power conversion efficiency and improved perovskite stability. Inspired by this development, this study presents the facile synthesis of mixed-cation perovskite nanocrystals based on FA((1-x))Cs(x)PbBr(3) (FA = CH(NH2)(2)). By detailed characterization of their morphological, optical, and physicochemical properties, it is found that the emission property of the perovskite, FA((1-x))Cs(x)PbBr(3), is significantly dependent on the substitution content of the Cs cations in the perovskite composition. These mixed-cation perovskites are employed as light emitters in light-emitting diodes (LEDs). With an optimized composition of FA(0.8)Cs(0.2)PbBr(3), the LEDs exhibit encouraging performance with a highest reported luminance of 55 005 cd m(-2) and a current efficiency of 10.09 cd A(-1). This work provides important instructions on the future compositional optimization of mixed-cation perovskite for obtaining high-performance LEDs. The authors believe this work is a new milestone in the development of bright and efficient perovskite LEDs.
|
|
