1. |
|
|
2. |
|
|
3. |
|
|
4. |
|
|
5. |
- Nappini, S., et al.
(författare)
-
Soft x-ray spectroscopies in liquids and at solid-liquid interface at BACH beamline at Elettra
- 2021
-
Ingår i: Review of Scientific Instruments. - : American Institute of Physics (AIP). - 0034-6748 .- 1089-7623. ; 92:1
-
Tidskriftsartikel (refereegranskat)abstract
- The beamline for advanced dichroism of the Istituto Officina dei Materiali-Consiglio Nazionale delle Ricerche, operating at the Elettra synchrotron in Trieste (Italy), works in the extreme ultraviolet-soft x-ray photon energy range with selectable light polarization, high energy resolution, brilliance, and time resolution. The beamline offers a multi-technique approach for the investigation of the electronic, chemical, structural, magnetic, and dynamical properties of materials. Recently, one of the three end stations has been dedicated to experiments based on electron transfer processes at the solid/liquid interfaces and during photocatalytic or electrochemical reactions. Suitable cells to perform soft x-ray spectroscopy in the presence of liquids and reagent gases at ambient pressure were developed. Here, we present two types of static cells working in transmission or in fluorescence yield and an electrochemical flow cell that allows us to carry out cyclic voltammetry in situ and electrodeposition on a working electrode and to study chemical reactions under operando conditions. Examples of x-ray absorption spectroscopy measurements performed under ambient conditions and during electrochemical experiments in liquids are presented.
|
|
6. |
- Ohlander, A., et al.
(författare)
-
DNA melting curve analysis on semi-transparent thin film microheater on flexible lab-on-foil substrate
- 2012
-
Ingår i: Proceedings of the 16th International Conference on Miniaturized Systems for Chemistry and Life Sciences, MicroTAS 2012. - 9780979806452 ; , s. 797-799
-
Konferensbidrag (refereegranskat)abstract
- This paper presents genotyping on a novel microheater concept using semi-transparent copper microheaters manufactured by roll-to-roll and lift-off on polyethylene napthalate (PEN) foil. Using a mesh structure, heater surfaces have been realized in one single metallization step with a manufacturing robustness higher than conventional meander structures. The thermal distribution of the meshes, evaluated using thermochromic-liquid-crystals (TLC), produced more homogenous heating characteristics compared to meanders. Parylene coated heaters were functionalized using copolymer poly(DMA-NAS-MAPS) to enable covalent DNA immobilization and successful melting curve analysis was performed differentiating between match and mismatch oligonucleotides.
|
|
7. |
- Pinaroli, G., et al.
(författare)
-
PERCIVAL : Possible applications in X-ray micro-tomography
- 2020
-
Ingår i: Journal of Instrumentation. - 1748-0221. ; 15:2
-
Tidskriftsartikel (refereegranskat)abstract
- X-ray computed micro-tomography (μCT) is one of the most advanced and common non-destructive techniques in the field of medical imaging and material science. It allows recreating virtual models (3D models), without destroying the original objects, by measuring three-dimensional X-ray attenuation coefficient maps of samples on the (sub) micrometer scale. The quality of the images obtained using μCT is strongly dependent on the performance of the associated X-ray detector i.e. to the acquisition of information of the X-ray beam traversing the patient/sample being precise and accurate. Detectors for μCT have to meet the requirements of the specific tomography procedure in which they are going to be used. In general, the key parameters are high spatial resolution, high dynamic range, uniformity of response, high contrast sensitivity, fast acquisition readout and support of high frame rates. At present the detection devices in commercial μCT scanners are dominated by charge-coupled devices (CCD), photodiode arrays, CMOS acquisition circuits and more recently by hybrid pixel detectors. Monolithic CMOS imaging sensors, which offer reduced pixel sizes and low electronic noise, are certainly excellent candidates for μCT and may be used for the development of novel high-resolution imaging applications. The uses of monolithic CMOS based detectors such as the PERCIVAL detector are being recently explored for synchrotron and FEL applications. PERCIVAL was developed to operate in synchrotron and FEL facilities in the soft X-ray regime from 250 eV to 1 keV and it could offer all the aforementioned technical requirements needed in μCT experiments. In order to adapt the system for a typical tomography application, a scintillator is required, to convert incoming X-ray radiation (∼ tens of KeV) into visible light which may be detected with high efficiency. Such a taper-based scintillator was developed and mounted in front of the sensitive area of the PERCIVAL imager. In this presentation we will report the setup of the detector system and preliminary results of first μCTs of reference objects, which were performed in the TomoLab at ELETTRA.
|
|