| 1. |
- Mathern, Alexandre, 1986, et al.
(författare)
-
Concrete Support Structures for Offshore Wind Turbines: Current Status, Challenges, and Future Trends
- 2021
-
Ingår i: Energies. - : MDPI AG. - 1996-1073 .- 1996-1073. ; 14:7
-
Forskningsöversikt (refereegranskat)abstract
- Today’s offshore wind turbine support structures market is largely dominated by steel structures, since steel monopiles account for the vast majority of installations in the last decade and new types of multi-leg steel structures have been developed in recent years. However, as wind turbines become bigger, and potential sites for offshore wind farms are located in ever deeper waters and ever further from the shore, the conditions for the design, transport, and installation of support structures are changing. In light of these facts, this paper identifies and categorizes the challenges and future trends related to the use of concrete for support structures of future offshore wind projects. To do so, recent advances and technologies still under development for both bottom-fixed and floating concrete support structures have been reviewed. It was found that these new developments meet the challenges associated with the use of concrete support structures, as they will allow the production costs to be lowered and transport and installation to be facilitated. New technologies for concrete support structures used at medium and great water depths are also being developed and are expected to become more common in future offshore wind installations. Therefore, the new developments identified in this paper show the likelihood of an increase in the use of concrete support structures in future offshore wind farms. These developments also indicate that the complexity of future support structures will increase due to the development of hybrid structures combining steel and concrete. These evolutions call for new knowledge and technical know-how in order to allow reliable structures to be built and risk-free offshore installation to be executed.
|
|
| 2. |
- Mathern, Alexandre, 1986
(författare)
-
Addressing the complexity of sustainability-driven structural design: Computational design, optimization, and decision making
- 2021
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Being one of the sectors with the largest environmental burden and high socio-economic impacts sets high requirements on the construction industry. At the same time, this provides the sector with great opportunities to contribute to the globally pursued sustainability transition. To cope with the increasing need for infrastructure and, at the same time, limit their sustainability impacts, changes and innovation in the construction sector are required. The greatest possibility to limit the sustainability impact of construction works is at the early design phase of construction projects, as many of the choices influencing sustainability are made at that point. Traditionally, an early choice of a preferred design is often made based on limited knowledge and past experience, considering only a handful of options. This preferred design is then taken on to the successive stages in the stepwise design process, leading to suboptimization. Alternatively, many different design choices could be considered and evaluated in a more holistic approach in order to find the most sustainable design for a particular application. However, finding design solutions that offer the best sustainability performance and fulfil all structural, performance and buildability requirements, require methods that allow considering different design options, analysing them, and assessing their sustainability. The aim of this thesis is to explore and develop methods enabling structural engineers to take sustainability objectives into account in the design of structures. Throughout this thesis, a number of methods have been explored to take sustainability aspects into account in the structural design process. As a first step, highly parameterized computer codes for sustainability-driven design have been developed. These codes interoperate with FE analysis software to automatically model and analyse design concepts over the whole design space and verify compliance with structural design standards. The codes were complemented with a harmonized method for life cycle sustainability performance assessment, in line with the state-of-the-art standards. Here, sustainability criteria were defined covering environmental, social, economic, buildability and structural performance for multi-criteria assessment of design concepts. To identify the most sustainable designs within the set, multi-objective optimization algorithms were used. Algorithms that address the high expense of constraint function evaluations of structural design problems were developed and integrated in the parameterized computer codes for sustainability-driven design. To ensure the applicability and validity of these methods, case studies based on real-world projects and common structural engineering problems were used in this thesis. Case studies for bridges and wind turbine foundations as well as a benchmark case of a reinforced concrete beam were investigated. The case studies highlight the potential of the methods explored to support the design of more sustainable structures, as well as the applicability of the methods in structural engineering practice. It is concluded that it is possible and beneficial to combine computational design, life cycle sustainability assessment, and multi-objective design optimization as a basis for decision making in the design phase of civil engineering projects. A wide adoption of such a sustainability-driven design optimization approach in structural engineering practice can directly improve the sustainability of the construction sector.
|
|
| 3. |
- Sundell, Jonas, 1984, et al.
(författare)
-
Comprehensive risk assessment of groundwater drawdown induced subsidence
- 2019
-
Ingår i: Stochastic Environmental Research and Risk Assessment. - : Springer Science and Business Media LLC. - 1436-3240 .- 1436-3259. ; 33:2, s. 427-449
-
Tidskriftsartikel (refereegranskat)abstract
- © 2019, The Author(s). We present a method for risk assessment of groundwater drawdown induced land subsidence when planning for sub-surface infrastructure. Since groundwater drawdown and related subsidence can occur at large distances from the points of inflow, the large spatial extent often implies heterogeneous geological conditions that cannot be described in complete detail. This calls for estimation of uncertainties in all components of the cause-effect chain with probabilistic methods. In this study, we couple four probabilistic methods into a comprehensive model for economic risk quantification: a geostatistical soil-stratification model, an inverse calibrated groundwater model, an elasto-plastic subsidence model, and a model describing the resulting damages and costs on individual buildings and constructions. Groundwater head measurements, hydraulic tests, statistical analyses of stratification and soil properties and an inventory of buildings are inputs to the models. In the coupled method, different design alternatives for risk reduction measures are evaluated. Integration of probabilities and damage costs result in an economic risk estimate for each alternative. Compared with the risk for a reference alternative, the best prior alternative is identified as the alternative with the highest expected net benefit. The results include spatial probabilistic risk estimates for each alternative where areas with significant risk are distinguished from low-risk areas. The efficiency and usefulness of this modelling approach as a tool for communication to stakeholders, decision support for prioritization of risk reducing measures, and identification of the need for further investigations and monitoring are demonstrated with a case study of a planned railway tunnel in Varberg, Sweden.
|
|
| 4. |
- Mathern, Alexandre, 1986, et al.
(författare)
-
Experimental study of time-dependent properties of a low-pH concrete for deposition tunnels
- 2018
-
Ingår i: fib Symposium. - 2617-4820. ; , s. 1726-1735
-
Konferensbidrag (refereegranskat)abstract
- The Swedish Nuclear Fuel and Waste Management Company developed a method for the final disposal of canisters for spent nuclear fuel in tunnels at depths of about 500 meters. The concept for closure of the deposition tunnels is based on a bentonite seal supported by a spherical concrete dome structure. In order to fulfil the requirements specific to the repository concept, a special mix of low-pH self-compacting concrete was developed. A series of large-scale castings and laboratory tests were conducted to gain experience on this low-pH concrete mix, in conjunction with the full-scale demonstration test of an unreinforced concrete dome plug in the underground hard rock laboratory in Äspö, Sweden. The laboratory tests aimed at studying the creep properties under high sustained compressive stresses of the low-pH concrete mix, its shrinkage properties and the properties of the rock-concrete interface. This paper provides an overview of these tests and analyses the latest results of the recently completed creep tests, which include 6 years of measurements. These results allow to improve understanding of the structural behaviour of the concrete plug and to assess the effects of the very high pressure acting on the plug on its deformations, cracking and water tightness.
|
|
| 5. |
- van Eldert, Jeroen, 1987-, et al.
(författare)
-
Application of Measurement While Drilling Technology to Predict Rock Mass Quality and Rock Support for Tunnelling
- 2020
-
Ingår i: Rock Mechanics and Rock Engineering. - : Springer. - 0723-2632 .- 1434-453X. ; 53:3, s. 1349-1358
-
Tidskriftsartikel (refereegranskat)abstract
- A tunnelling project is normally initiated with a site investigation to determine the in situ rock mass conditions and to generate the basis for the tunnel design and rock support. However, since site investigations often are based on limited information (surface mapping, geophysical profiles, few bore holes, etc.), the estimation of the rock mass conditions may contain inaccuracies, resulting in underestimating the required rock support. The study hypothesised that these inaccuracies could be reduced using Measurement While Drilling (MWD) technology to assist in the decision-making process. A case study of two tunnels in the Stockholm bypass found the rock mass quality was severely overestimated by the site investigation; more than 45% of the investigated sections had a lower rock mass quality than expected. MWD data were recorded in 25 m grout holes and 6 m blast holes. The MWD data were normalised so that the long grout holes with larger hole diameters and the shorter blast holes with smaller hole diameters gave similar results. With normalised MWD data, it was possible to mimic the tunnel contour mapping; results showed good correlation with mapped Q-value and installed rock support. MWD technology can improve the accuracy of forecasting the rock mass ahead of the face. It can bridge the information gap between the early, somewhat uncertain geotechnical site investigation and the geological mapping done after excavation to optimise rock support.
|
|
| 6. |
- Sundell, Jonas, 1984, et al.
(författare)
-
Economic valuation of hydrogeological information when managing groundwater drawdown
- 2019
-
Ingår i: Hydrogeology Journal. - : Springer Science and Business Media LLC. - 1431-2174 .- 1435-0157. ; 27:4, s. 1111-1130
-
Tidskriftsartikel (refereegranskat)abstract
- © 2019, The Author(s). A procedure is presented for valuation of information analysis (VOIA) to determine the need for additional information when assessing the effect of several design alternatives to manage future disturbances in hydrogeological systems. When planning for groundwater extraction and drawdown in areas where risks—such as land subsidence, wells running dry and drainage of streams and wetlands—are present, the need for risk-reducing safety measures must be carefully evaluated and managed. The heterogeneity of the subsurface calls for an assessment of trade-offs between the benefits of additional information to reduce the risk of erroneous decisions and the cost of collecting this information. A method is suggested that combines existing procedures for inverse probabilistic groundwater modelling with a novel method for VOIA. The method results in (1) a prior analysis where uncertainties regarding the efficiency of safety measures are estimated, and (2) a pre-posterior analysis, where the benefits of expected uncertainty reduction deriving from additional information are compared with the costs for obtaining this information. In comparison with existing approaches for VOIA, the method can assess multiple design alternatives, use hydrogeological parameters as proxies for failure, and produce spatially distributed VOIA maps. The method is demonstrated for a case study of a planned tunnel in Stockholm, Sweden, where additional investigations produce a low number of benefits as a result of low failure rates for the studied alternatives and a cause-effect chain where the resulting failure probability is more dependent on interactions within the whole system rather than on specific features.
|
|
| 7. |
- Ait Ali, Abderrahman, et al.
(författare)
-
Evaluating the mix of maintenance activities on railway crossings with respect to life-cycle costs
- 2024
-
Ingår i: European Journal of Transport and Infrastructure Research. - : TU Delft OPEN Publishing. - 1567-7141 .- 1567-7133. ; 24:1, s. 1-29
-
Tidskriftsartikel (refereegranskat)abstract
- Switches & crossings (S&Cs) are vital assets as they allow for increased railway capacity by introducing flexibility and connectivity in railway networks. At the same time, this makes them critical since they can cause costly delays and disruptions if they are not well maintained. This motivates studies to improve maintenance strategies of S&Cs, considering both the life-cycle costs (LCCs) of the assets and socio-economic transportation costs for passengers and freight customers. In this paper, the interdependence between deterioration mechanisms, maintenance activities, and expected LCC (including transportation costs) for the crossing panel – an S&C subsystem – is investigated using a combination of mechanical and econometric modelling. The interrelation between the degradation of contact geometry and track settlement is analysed using simulations of dynamic vehicle– turnout interaction. Long-term mechanical degradation of the crossing panel is simulated for different maintenance strategies that correspond to different timing of the associated maintenance measures (crossing repair welding and tamping). This provides the basis for analysing the interdependence between preventive and corrective activities using econometric modelling. Based on a case study of a common type of S&Cs in the Swedish infrastructure, the impact of different maintenance strategies on LCC and transportation costs is analysed. Opportunities and challenges in the development of more economically effective maintenance strategies of S&Cs are discussed.
|
|
| 8. |
- Rempling, Rasmus, 1976, et al.
(författare)
-
Utmattning
- 2021
-
Ingår i: Betonghandbok material - Hårdnad betong, fysikaliska egenskaper och beständighet. - 9789179170882 ; , s. 485-510
-
Bokkapitel (övrigt vetenskapligt/konstnärligt)
|
|
| 9. |
- Petersson, Jesper, 1974
(författare)
-
Blurring the shoreline: De- and re-infrastructuring and the changing colors of European flood policy
- 2021
-
Ingår i: Environment and Planning E: Nature and Space. - : SAGE Publications. - 2514-8494 .- 2514-8494 .- 2514-8486. ; 4:2, s. 623-644
-
Tidskriftsartikel (refereegranskat)abstract
- This paper provides a genealogy of the emergence of a common EU flood policy, including the scope and direction of this policy. Noticing how EU policy proposes green infrastructure (associated with using nature as a buffer zone in managing floods) as an alternative to grey infrastructure (implying fixed installations of concrete and cement), this paper adopts the theoretical lens of the so-called infrastructural turn, which advocates a relational investigation of infrastructure. By engaging this approach, the paper shows how flood infrastructure can contain very different compositions of (unruly) water and (settled) land. A narrative of a historically strong focus on guarding society from the powerful forces of nature through a fixed line of defense is increasingly giving way to more muddy states—quite literally—where society is expected to learn to live with flooding and show ecological consideration. To capture the EU’s, and especially the European Commission’s efforts to establish a pan-European flood infrastructure that accommodates this turn, the concepts of de- and re-infrastructuring are developed. These concepts act as heuristic devices to capture how policy performs some combinations between water and land as constituting an attractive and functional flood infrastructure, but constitutes other infrastructural relations of the aquatic and the terrestrial as undesirable and, hence, as malfunctioning. This performative act of distinguishing between what constitutes “good and proper” versus “bad and undesirable” infrastructure is referred to as a politics of infrastructure.
|
|
| 10. |
- Dymitrow, Mirek, et al.
(författare)
-
Crossing dichotomies and breaking mental patterns: Green business development when all else fails?
- 2017
-
Ingår i: 8th International Scientific Conference “Rural Development 2017: Bioeconomy Challenges”, 23–24 November, 2017 Kaunas, Lithuania.
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Obtaining sustainable and inclusive societal organization is not merely a simple matter of ‘doing it’ by subscribing to some winning formula. Given that conceptual frameworks always guide our thoughts, judgments and actions (Latour, 2013; Harvey, 1996; Dennett, 1993), the ways in which we relate to concepts chosen to serve as guiding forces for future development will eventually determine its outcome. As scholarly evidence continuously suggests the concepts ‘rural’ and ‘urban’ are increasingly recognized as artificial barriers for conducting sound and integrated development endeavors in a globalized reality of interconnectedness. In line with the Sustainable Development Goals, which aim to eradicate poverty, shield the planet and safeguard prosperity for all, commitment to universal access to healthy food year round has become an important agenda point. This, however, has been exacerbated by binary thinking and separate ways of doing policy. This paper aims to share experiences from a unique project launched in the northern parts of Gothenburg, Sweden’s second largest city. While the area offers ample resources and immense opportunities for areal economies, it at the same time remains one of Gothenburg’s most segregated, with high levels of unemployment, ill health and crime. The uniqueness of the project lies not only in its way of abridging the rural-urban divide, but also by consciously deferring from the debilitating rhetoric of previous ‘immigrant policies’, and instead focusing on agricultural productivity, small-scale food producers and sustainable food strategies. Such exhortations to bridge between philosophical and material polarities, however, have not come without conceptual and practical challenges, something this paper aims to subsume and open up to debate.
|
|
