| 1. |
|
|
| 2. |
- Nybacka, Mikael, et al.
(författare)
-
Project: CASTT - Centre for Automotive Systems Technologies and Testing
- 2007
-
Annan publikation (populärvet., debatt m.m.)abstract
- Through the Centre for Automotive Systems Technologies and Testing, Luleå University of Technology aims to first of all support automotive winter testing in Northern Sweden. This means to support the local automotive test entrepreneurs and through them their customers: the car manufacturers and their suppliers. To succeed in this task, the center relies on the university's areas of leading research and most importantly on the cooperation between those areas.
|
|
| 3. |
|
|
| 4. |
- Karlsson, Patrik, 1973-, et al.
(författare)
-
Galling resistance and wear mechanisms for cold-work tool steels in lubricated sliding against high strength stainless steel sheets
- 2012
-
Ingår i: Wear. - Amsterdam : Elsevier. - 0043-1648 .- 1873-2577. ; 286-287, s. 92-97
-
Tidskriftsartikel (refereegranskat)abstract
- Tool damage in sheet metal forming of stainless steel is of high concern for the forming industry. In the present work, ingot cast AISI D2 and advanced powder metallurgy tool steel (PM) cold-work tool steels were evaluated and ranked regarding wear mechanisms and galling resistance. Wear tests were performed using a slider-on-flat-surface (SOFS) tribometer in sliding against austenitic–ferritic (duplex) stainless steel sheets at different contact pressures in lubricated conditions. The best galling resistance was observed for the nitrogen alloyed PM tool steels. Abrasive scratching of the tool surfaces and transfer of sheet material due to adhesive wear were the main metal forming tool surface damage mechanisms. By increasing the hardness of one PM sheet metal forming tool grade, the galling resistance was enhanced.
|
|
| 5. |
- Vilardell, A. M., et al.
(författare)
-
B2-structured Fe3Al alloy manufactured by laser powder bed fusion : Processing, microstructure and mechanical performance
- 2023
-
Ingår i: Intermetallics (Barking). - : Elsevier. - 0966-9795 .- 1879-0216. ; 156
-
Tidskriftsartikel (refereegranskat)abstract
- Prealloyed Fe3Al was successfully manufactured by laser powder bed fusion. The best set of process parameters led to parts with a relative density of 99.5 %, a surface roughness, Sa, of 31.5 ± 5.6 μm and a hardness of 319 ± 14 HV0.1. Its microstructure as well as its mechanical properties at room and high temperatures were analyzed. The results of the chemical composition showed minor variations in aluminum content oscillating between 21 and 28 at.% along the melt pool. Additionally, elongated grains were observed to grow parallel to the building direction, as well as the development of a weak 001 texture along the building direction. The mechanical properties were influenced by the temperature. Compression tests showed a loss in strength with the increase in temperature, from a yield strength of 621 ± 40 MPa at room temperature to 89 ± 20 MPa at 650 °C. Reciprocating sliding wear tests showed that fragmentation of the intermetallic at room temperature occurs, whereas plastic deformation dominated at higher temperatures. For all temperatures, tribochemical wear was also present due to the oxidation of wear debris.
|
|
| 6. |
- Li, Xiaojian, 1991, et al.
(författare)
-
A new method for performance map prediction of automotive turbocharger compressors with both vaneless and vaned diffusers
- 2021
-
Ingår i: Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering. - : SAGE Publications. - 2041-2991 .- 0954-4070. ; 235:6, s. 1734-1747
-
Tidskriftsartikel (refereegranskat)abstract
- A new approach to predict the performance maps of automotive turbocharger compressors is presented. Firstly, a polynomial equation is applied to fit the experimental data of flow coefficient ratios for the centrifugal compressors with both vaneless and vaned diffusers. Based on this equation, the choke and surge flow coefficients under different machine Mach numbers can be quickly predicted. Secondly, a physically based piecewise elliptic equation is used to define compressors’ characteristic curves in terms of efficiency ratio. By introducing the flow coefficient ratio into the efficiency correlation, the empirical coefficients in the piecewise elliptic equation are uniquely calibrated by the experimental data, forming a unified algebraic equation to match the efficiency maps of the compressors with both vaneless and vaned diffusers. Then, a new universal equation, which connects the work coefficient, the impeller outlet flow coefficient and the non-dimensional equivalent impeller outlet width, is derived by using classical aerothermodynamic method. The off-design pressure ratio is predicted based on the equivalent impeller outlet width with less knowledge of the compressor geometry and no empirical coefficients. Finally, three state-of-the-art turbocharger compressors (one with vaneless diffuser, two with vaned diffusers) are chosen to validate the proposed method, and the results show a satisfactory accuracy for the performance map prediction. This method can be used for the preliminary design of turbocharger compressors with both vaneless and vaned diffusers, or to assess the design feasibility and challenges of the given design specifications.
|
|
| 7. |
|
|
| 8. |
- Bayani, Mohsen, 1981
(författare)
-
Squeak and Rattle Prediction for Robust Product Development in the automotive industry
- 2021
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Squeak and rattle are nonstationary, irregular, and impulsive sounds that are audible inside the car cabin. For decades, customer complaints about squeak and rattle have been, and still are, among the top quality issues in the automotive industry. These annoying sounds are perceived as quality defect indications and burden warranty costs to the car manufacturers. Today, the quality improvements regarding the persistent type of sounds in the car, as well as the increasing popularity of electric engines, as green and quiet propulsion solutions, stress the necessity for attenuating annoying sounds like squeak and rattle more than in the past. The economical and robust solutions to this problem are to be sought in the pre-design-freeze phases of the product development and by employing design-concept-related practices. To achieve this goal, prediction and evaluation tools and methods are required to deal with the squeak and rattle quality issues upfront in the product development process. The available tools and methods for the prediction of squeak and rattle sounds in the pre-design-freeze phases of a car development process are not yet sufficiently mature. The complexity of the squeak and rattle events, the existing knowledge gap about the mechanisms behind the squeak and rattle sounds, the lack of accurate simulation and post-processing methods, as well as the computational cost of complex simulations are some of the significant hurdles in this immaturity. This research addresses this problem by identifying a framework for the prediction of squeak and rattle sounds based on a cause-and-effect diagram. The main domains and the elements and the sub-contributors to the problem in each domain within this framework are determined through literature studies, field explorations and descriptive studies conducted on the subject. Further, improvement suggestions for the squeak and rattle evaluation and prediction methods are proposed through prescriptive studies. The applications of some of the proposed methods in the automotive industry are demonstrated and examined in industrial problems. The outcome of this study enhances the understanding of some of the parameters engaged in the squeak and rattle generation. Simulation methods are proposed to actively involve the contributing factors studied in this work for squeak and rattle risk evaluation. To enhance the efficiency and accuracy of the risk evaluation process, methods were investigated and proposed for the system excitation efficiency, modelling accuracy and efficiency and quantification of the response in the time and frequency domains. The demonstrated simulation methods besides the improved understanding of the mechanisms behind the phenomenon can facilitate a more accurate and robust prediction of squeak and rattle risk during the pre-design-freeze stages of the car development.
|
|
| 9. |
- Pieringer, Astrid, 1979, et al.
(författare)
-
Investigation of railway curve squeal using a combination of frequency- and time-domain models
- 2016
-
Ingår i: Proceedings of the 12h International Workshop on Railway Noise (IWRN12), Terrigal, Australia, September 12-16. ; , s. 444 - 451
-
Konferensbidrag (refereegranskat)abstract
- Railway curve squeal arises from self-excited vibrations during curving. In this paper, a frequency- and a timedomainapproach for curve squeal are compared. In particular, the capability of the frequency-domain model topredict the onset of squeal and the squeal frequencies is studied. In the frequency-domain model, linear stabilityis investigated through complex eigenvalue analysis. The time-domain model is based on a Green's functionsapproach and uses a convolution procedure to obtain the system response. To ensure comparability, the samesubmodels are implemented in both squeal models. The structural flexibility of a rotating wheel is modelled byadopting Eulerian coordinates. To account for the moving wheel‒rail contact load, the so-called moving elementmethod is used to model the track. The local friction characteristics in the contact zone is modelled inaccordance with Coulomb's law with a constant friction coefficient. The frictional instability arises due togeometrical coupling. In the time-domain model, Kalker's non-linear, non-steady state rolling contact modelincluding the algorithms NORM and TANG for normal and tangential contact, respectively, is solved in eachtime step. In the frequency-domain model, the normal wheel/rail contact is modelled by a linearization of theforce-displacement relation obtained with NORM around the quasi-static state and full-slip conditions areconsidered in tangential direction. Conditions similar to those of a curve on the Stockholm metro exposed tosevere curve squeal are studied with both squeal models. The influence of the wheel-rail friction coefficient andthe direction of the resulting creep force on the occurrence of squeal is investigated for vanishing train speed. Results from both models are similar in terms of the instability range in the parameter space and the predictedsqueal frequencies.
|
|
| 10. |
- Karlsson, Patrik, 1973-, et al.
(författare)
-
Galling resistance evaluation of tool steels by two different laboratory test methods for sheet metal forming
- 2012
-
Ingår i: Lubrication Science. - : John Wiley & Sons. - 0954-0075 .- 1557-6833. ; 24:6, s. 263-272
-
Tidskriftsartikel (refereegranskat)abstract
- Adhesive accumulation of work material on the tool surface is today a major problem in many sheet metal-forming applications. Different laboratory test methods are used to investigate galling with respect to different tool materials, lubricants and process conditions. In the present study, the galling resistance of a modern nitrogen-alloyed powder metallurgy tool steel and an conventional ingot cast D2 type tool steel was evaluated under lubricated sliding against ferritic stainless steel sheets using a commercial pin-on-disc (POD) and an in-house made slider-on-flat-surface (SOFS) tribotester. The investigated tool steels ranked similarly in terms of galling resistanc in both test methods. However, sliding distances to galling were longer for the SOFS equipment due to continuous sliding on new lubricated sheet surface. Best performance was demonstrated by the powder metallurgy tool steel treated to 65 HRC. Differences in friction behaviour and galling initiation were analysed on the basis of the two different working conditions, i.e. open (SOFS) and closed (POD) tribosystems. Copyright © 2012 John Wiley & Sons, Ltd.
|
|
