| 1. |
- Fredenberg, Erik, 1979-
(författare)
-
Spectral Mammography with X-Ray Optics and a Photon-Counting Detector
- 2009
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Early detection is vital to successfully treating breast cancer, and mammography screening is the most efficient and wide-spread method to reach this goal. Imaging low-contrast targets, while minimizing the radiation exposure to a large population is, however, a major challenge. Optimizing the image quality per unit radiation dose is therefore essential. In this thesis, two optimization schemes with respect to x-ray photon energy have been investigated: filtering the incident spectrum with refractive x-ray optics (spectral shaping), and utilizing the transmitted spectrum with energy-resolved photon-counting detectors (spectral imaging). Two types of x-ray lenses were experimentally characterized, and modeled using ray tracing, field propagation, and geometrical optics. Spectral shaping reduced dose approximately 20% compared to an absorption-filtered reference system with the same signal-to-noise ratio, scan time, and spatial resolution. In addition, a focusing pre-object collimator based on the same type of optics reduced divergence of the radiation and improved photon economy by about 50%. A photon-counting silicon detector was investigated in terms of energy resolution and its feasibility for spectral imaging. Contrast-enhanced tumor imaging with a system based on the detector was characterized and optimized with a model that took anatomical noise into account. Improvement in an ideal-observer detectability index by a factor of 2 to 8 over that obtained by conventional absorption imaging was found for different levels of anatomical noise and breast density. Increased conspicuity was confirmed by experiment. Further, the model was extended to include imaging of unenhanced lesions. Detectability of microcalcifications increased no more than a few percent, whereas the ability to detect large tumors might improve on the order of 50% despite the low attenuation difference between glandular and cancerous tissue. It is clear that inclusion of anatomical noise and imaging task in spectral optimization may yield completely different results than an analysis based solely on quantum noise.
|
|
| 2. |
|
|
| 3. |
- Fredenberg, Erik, PhD, 1979-, et al.
(författare)
-
A low-absorption x-ray energy filter for small-scale applications
- 2009
-
Ingår i: Optics Express. - : The Optical Society. - 1094-4087. ; 17:14, s. 11388-11398
-
Tidskriftsartikel (refereegranskat)abstract
- We present an experimental and theoretical evaluation of an x-ray energy filter based on the chromatic properties of a prism-array lens (PAL). It is intended for small-scale applications such as medical imaging. The PAL approximates a Fresnel lens and allows for high efficiency compared to filters based on ordinary refractive lenses, however at the cost of a lower energy resolution. Geometrical optics was found to provide a good approximation for the performance of a flawless lens, but a field-propagation model was used for quantitative predictions. The model predicted a 0.29 ΔE/E energy resolution and an intensity gain of 6.5 for a silicon PAL at 23.5 keV. Measurements with an x-ray tube showed good agreement with the model in energy resolution and peak energy, but a blurred focal line contributed to a 29% gain reduction. We believe the blurring to be caused mainly by lens imperfections, in particular at the periphery of the lens.
|
|
| 4. |
- Decrop, Deborah, et al.
(författare)
-
Single-step manufacturing of femtoliter microwell arrays in a novel surface energy mimicking polymer
- 2015
-
Ingår i: 18th International Conference on Solid-State Sensors, Actuators and Microsystems (IEEE TRANSDUCER 2015). - : IEEE.
-
Konferensbidrag (refereegranskat)abstract
- We report a novel polymer material formulation and stamp-molding technique that enable rapid single-step manufacturing of hydrophilic-in-hydrophobic microwell arrays. We developed a modified thiol-ene-epoxy polymer (mOSTE+) formulation that mimics the surface energy of its mold during polymerization. The polymer inherits the surface energy from the mold through molecular self-assembly, in which functional monomers self-assemble at the interface between the liquid prepolymer and the mold surface. Combining this novel mOSTE+ material with a stamp-molding process leads to simultaneous surface energy mimicking and micro-structuring. This method was used to manufacture microwells with hydrophilic bottom and hydrophobic sidewall, depressed in a surrounding hydrophobic surface. The microwell arrays were successfully tested for the self-assembly of 62’000 femtoliter-droplets. Such femtoliter droplet arrays are useful for, e.g., digital ELISA and single cell/molecule analysis applications.
|
|
| 5. |
- Liu, Yuanhua, 1971, et al.
(författare)
-
Considering the importance of user profiles in interface design
- 2009
-
Ingår i: User Interfaces. ; , s. 23-
-
Bokkapitel (övrigt vetenskapligt/konstnärligt)abstract
- User profile is a popular term widely employed during product design processes by industrial companies. Such a profile is normally intended to represent real users of a product. The ultimate purpose of a user profile is actually to help designers to recognize or learn about the real user by presenting them with a description of a real user’s attributes, for instance; the user’s gender, age, educational level, attitude, technical needs and skill level. The aim of this chapter is to provide information on the current knowledge and research about user profile issues, as well as to emphasize the importance of considering these issues in interface design. In this chapter, we mainly focus on how users’ difference in expertise affects their performance or activity in various interaction contexts. Considering the complex interaction situations in practice, novice and expert users’ interactions with medical user interfaces of different technical complexity will be analyzed as examples: one focuses on novice and expert users’ difference when interacting with simple medical interfaces, and the other focuses on differences when interacting with complex medical interfaces. Four issues will be analyzed and discussed: (1) how novice and expert users differ in terms of performance during the interaction; (2) how novice and expert users differ in the perspective of cognitive mental models during the interaction; (3) how novice and expert users should be defined in practice; and (4) what are the main differences between novice and expert users’ implications for interface design. Besides describing the effect of users’ expertise difference during the interface design process, we will also pinpoint some potential problems for the research on interface design, as well as some future challenges that academic researchers and industrial engineers should face in practice.
|
|
| 6. |
- Macias, Raul, et al.
(författare)
-
Performance of the Load-in-the-Loop Single Op-Amp Voltage Controlled Current Source from the Op-Amp Parameters
- 2010
-
Ingår i: Journal of Physics: Conference Series. - : Institute of Physics Publishing Ltd.. - 1742-6596 .- 1742-6588.
-
Konferensbidrag (refereegranskat)abstract
- In recent years, Electrical Bioimpedance (EBI) methods have gained importance. These methods are often based on obtaining impedance spectrum in the range of β-dispersion, i.e. from a few kHz up to some MHz. To measure EBI a constant current is often injected and the voltage across the tissue under study (TUS) is recorded. Due to the performance of the current source influences the performance of the entire system, in terms of frequency range, several designs have been implemented and studied. In this paper the basic structure of a Voltage-Controlled Current Source (VCCS) based on a single Op-Amp in inverter configuration with a floating load, known as load-in-the-loop current source, is revisited and studied deeply. We focus on the dependence of the output impedance with the circuit parameters, i.e. the feedback resistor and the inverter-input resistor, and the Op-Amp main parameters, i.e. open loop gain, CMRR and input impedance. After obtaining the experimental results and comparing to the theoretical and simulated ones, they confirm the design under study can be a good solution for multi-frequency wideband EBI applications because of higher values of the output impedance than 100kΩ at 1MHz are obtained. Furthermore, an enhancement of the basic design, using a current conveyor as a first stage, is proposed, studied and implemented.
|
|
| 7. |
- Seoane, Fernando, et al.
(författare)
-
Conductive Polymer Films as Textrodes for Biopotential Sensing
- 2011
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Introduction: After several years of progresses in textile technology and wearable measurement instrumentation, applications of wearable textile-electronics systems are arising providing a stable background for commercial applications. So far, the available commercial solutions are centered on fitness applications and mostly based in the acquisition of heart rate through Textile Electrodes (Textrodes) based on metallic threads or on conductive rubber compounds. Methods and Materials: In this work a novel material approach is presented to produce Textrodes for acquisition of Electrocardiographic (ECG) signals using a conductive polypropylene (PP1386 from Premix, Finland) polymer material. The polymer was film extruded into thin films, and used as such in the Textrode. Conductive Polymer Films (CPF) have been used to produce Textrodes, and its measurement performance has been compared with the ECG signals obtained with commercial Textrode fabrics and conventional Ag/AgCl electrodes. In order to set up the same measurement conditions, a chest strap tailored to host the testing electrodes has been used. Results: The close resemblance of the ECG acquired with the textile fabric electrodes, the Ag/AgCl electrodes and the PP1386 CPF electrodes suggest that the Polymer Electrodes PP1386 are a feasible alternative to the current textile fabrics that use silver thread as conductive material and also to conductive rubber material. Discussion & Conclusion: The availability of the Conductive Polymer Electrode PP1386 in a film form allows the manufacturing of electrodes by conventional textile processes, like lamination or sewing, therefore facilitating the transition from lab prototyping to industrial manufacturing. Replacing the traditional silver thread as conductive element in the fabrication of Textrodes will definitely reduce the material cost per Textrode. Biocompatibility issues and manufacturability issues must be addressed but the exhibited functional performance is showing encouraging results.
|
|
| 8. |
- Fhager, Andreas, 1976, et al.
(författare)
-
Image Reconstruction in Microwave Tomography Using a Dielectric Debye Model
- 2012
-
Ingår i: IEEE Transactions on Biomedical Engineering. - 0018-9294 .- 1558-2531. ; 59:1, s. 156 - 166
-
Tidskriftsartikel (refereegranskat)abstract
- In this paper, quantitative dielectric image reconstruction based on broadband microwave measurements is investigated. A time-domain-based algorithm is derived where Debye model parameters are reconstructed in order to take into account the strong dispersive behavior found in biological tissue. The algorithm is tested with experimental and numerical data in order to verify the algorithm and to investigate improvements in the reconstructed image resulting from the improved description of the dielectric properties of the tissue when using broadband data. The comparison is made in relation to the more commonly used conductivity model. For the evaluation, two examples were considered, the first was a lossy saline solution and the second was less lossy tap water. Both liquids are strongly dispersive and used as a background medium in the imaging examples. The results show that the Debye model algorithm is of most importance in the tap water for a bandwidth of more than 1.5 GHz. Also the saline solution exhibits a dispersive behavior but since the losses restrict the useful bandwidth, the Debye model is of less significance even if somewhat larger and stronger artifacts can be seen in the conductivity model reconstructions.
|
|
| 9. |
- Hafid, Abdelakram, et al.
(författare)
-
Full Impedance Cardiography Measurement Device Using Raspberry PI3 and System-on-Chip Biomedical Instrumentation Solutions
- 2018
-
Ingår i: IEEE journal of biomedical and health informatics. - : IEEE-INST ELECTRICAL ELECTRONICS ENGINEERS INC. - 2168-2194 .- 2168-2208. ; 22:6, s. 1883-1894
-
Tidskriftsartikel (refereegranskat)abstract
- Impedance cardiography (ICG) is a noninvasive method for monitoring cardiac dynamics using electrical bioimpedance (EBI) measurements. Since its appearance more than 40 years ago, ICG has been used for assessing hemodynamic parameters. This paper presents a measurement system based on two System on Chip (SoC) solutions and Raspberry PI, implementing both a full three-lead ECG recorder and an impedance cardiographer, for educational and research development purposes. Raspberry PI is a platform supporting Do-I t-Yourself project and education applications across the world. The development is part of Biosignal PI, an open hardware platform focusing in quick prototyping of physiological measurement instrumentation. The SoC used for sensing cardiac biopotential is the ADAS1000, and for the EBI measurement is the AD5933. The recordings were wirelessly transmitted through Bluetooth to a PC, where the waveforms were displayed, and hemodynamic parameters such as heart rate, stroke volume, ejection time and cardiac output were extracted from the ICG and ECG recordings. These results show how Raspberry PI can be used for quick prototyping using relatively widely available and affordable components, for supporting developers in research and engineering education. The design and development documents will be available on www.BiosignalPl.com, for open access under a Non Commercial-Share A like 4.0 International License.
|
|
| 10. |
- Pfeiffer, Christoph, 1989, et al.
(författare)
-
Localizing on-scalp MEG sensors using an array of magnetic dipole coils
- 2018
-
Ingår i: Plos One. - : Public Library of Science (PLoS). - 1932-6203. ; 13:5
-
Tidskriftsartikel (refereegranskat)abstract
- Accurate estimation of the neural activity underlying magnetoencephalography (MEG) signals requires co-registration i.e., determination of the position and orientation of the sensors with respect to the head. In modern MEG systems, an array of hundreds of low- T c SQUID sensors is used to localize a set of small, magnetic dipole-like (head-position indicator, HPI) coils that are attached to the subject's head. With accurate prior knowledge of the positions and orientations of the sensors with respect to one another, the HPI coils can be localized with high precision, and thereby the positions of the sensors in relation to the head. With advances in magnetic field sensing technologies, e.g., high-T-c SQUIDs and optically pumped magnetometers (OPM), that require less extreme operating temperatures than low- T-c SQUID sensors, on-scalp MEG is on the horizon. To utilize the full potential of on-scalp MEG, flexible sensor arrays are preferable. Conventional co-registration is impractical for such systems as the relative positions and orientations of the sensors to each other are subject-specific and hence not known a priori. Herein, we present a method for co-registration of on-scalp MEG sensors. We propose to invert the conventional co-registration approach and localize the sensors relative to an array of HPI coils on the subject's head. We show that given accurate prior knowledge of the positions of the HPI coils with respect to one another, the sensors can be localized with high precision. We simulated our method with realistic parameters and layouts for sensor and coil arrays. Results indicate co-registration is possible with sub-millimeter accuracy, but the performance strongly depends upon a number of factors. Accurate calibration of the coils and precise determination of the positions and orientations of the coils with respect to one another are crucial. Finally, we propose methods to tackle practical challenges to further improve the method.
|
|
