| 1. |
- Piscitelli, Francesco, et al.
(författare)
-
Neutron reflectometry on highly absorbing films and its application to (B4C)-B-10-based neutron detectors
- 2016
-
Ingår i: Royal Society of London. Proceedings A. Mathematical, Physical and Engineering Sciences. - : The Royal Society. - 1364-5021 .- 1471-2946. ; 472:2185
-
Tidskriftsartikel (refereegranskat)abstract
- Neutron reflectometry is a powerful tool used for studies of surfaces and interfaces. The absorption in the typical studied materials is neglected and this technique is limited only to the reflectivity measurement. For strongly absorbing nuclei, the absorption can be directly measured by using the neutron-induced fluorescence technique which exploits the prompt particle emission of absorbing isotopes. This technique is emerging from soft matter and biology where highly absorbing nuclei, in very small quantities, are used as a label for buried layers. Nowadays, the importance of absorbing layers is rapidly increasing, partially because of their application in neutron detection; a field that has become more active also due to the He-3-shortage. We extend the neutron-induced fluorescence technique to the study of layers of highly absorbing materials, in particular (B4C)-B-10. The theory of neutron reflectometry is a commonly studied topic; however, when a strong absorption is present the subtle relationship between the reflection and the absorption of neutrons is not widely known. The theory for a general stack of absorbing layers has been developed and compared to measurements. We also report on the requirements that a (B4C)-B-10 layer must fulfil in order to be employed as a converter in neutron detection.
|
|
| 2. |
- Fritioff, T., et al.
(författare)
-
Purification of radioactive neutron-rich argon beams using an ion source in charge breeding mode
- 2006
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576 .- 0167-5087. ; 556:1, s. 31-37
-
Tidskriftsartikel (refereegranskat)abstract
- Measurements of nuclear properties of some neutron-rich asymmetric fission isotopes at an ISOL laboratory present a severe problem when a plasma ion source is used as the primary ion-source. The problem is associated with intense multi-charged symmetric fission contaminants that cannot be mass-separated from asymmetric fission products. In this work we demonstrate how this problem can be overcome on-line by using an electron cyclotron resonance ion source (ECRIS) as a charge-breeding secondary ion-source. Mixed Ar+/Kr2+/Xe3+ radioactive beams from an plasma ion-source were injected into the PHOENIX ECRIS that currently is installed at the ISOLDE facility at CERN in order to improve the ratio of Ar to the background contaminants of Kr and Xe. The signal to noise ratio was improved by more than two orders of magnitude after charge-breeding and mass-separation of the Ar8+, Ar9+ beams. The information on the decay of the Ar-48 nucleus obtained in these tests is useful for a better understanding of the origin of the Ca-48/Ca-46 meteorite isotopic anomaly. Potential applications of the method are discussed.
|
|
| 3. |
- Hidvegi, Attila, et al.
(författare)
-
A system for distributing high-speed synchronous high-precision clock and trigger data over large distances
- 2008
-
Ingår i: Nuclear Science Symposium Conference Record, 2008. NSS '08. IEEE. - 9781424427147 ; , s. 2581-2584
-
Konferensbidrag (refereegranskat)abstract
- The distribution of precise timing throughout the European X-ray Free Electron Laser project [1] (XFEL) and its triggering system is a very challenging part of the system design. ADCs in data acquisition systems and DACs in control systems will require very high precision clocks. The clocks need to be synchronous to each other, both in frequency and phase, with a jitter performance better than 5 ps (RMS). At some high-speed ADCs it might even need a precision down to 0.1 ps. The frequencies that must be available are the main 1.3 GHz and some frequencies below, which are all derived from the main frequency. The phase needs to be adjustable to allow synchronization between separate devices. Triggering information needs to be distributed over the system, so that controlling instructions can be carried out at a very precise time. This is very important since the beam will travel with the speed of light, and there is no possibility for information to be sent back and forth. This requires an absolute timing to be distributed over the system. Both the main clock and triggering information will be transmitted over the same fiber cable, one to each device. An advanced synchronization method needs to be developed to synchronize the phases of the clocks throughout the whole system. The delay through the cable can change with temperature, and due to long cables the total change through a single cable can be significant. It is essential that the clocks are stable and not drifting away from each other. Therefore a continuous calibration method is needed, ensuring that the clocks are synchronous throughout the whole system. A prototype of such a system is being developed and a first version is expected to be completed in 2009 Ql.
|
|
| 4. |
- Reza, Salim, 1985-, et al.
(författare)
-
Smart dosimetry by pattern recognition using a single photon counting detector system in time over threshold mode
- 2012
-
Ingår i: Journal of Instrumentation. - 1748-0221 .- 1748-0221. ; 7:1
-
Tidskriftsartikel (refereegranskat)abstract
- The function of a dosimeter is to determine the absorbed dose of radiation, for those cases in which, generally, the particular type of radiation is already known. Lately, a number of applications have emerged in which all kinds of radiation are absorbed and are sorted by pattern recognition, such as the Medipix2 application in [1]. This form of smart dosimetry enables measurements where not only the total dosage is measured, but also the contributions of different types of radiation impacting upon the detector surface. Furthermore, the use of a photon counting system, where the energy deposition can be measured in each individual pixel, ensures measurements with a high degree of accuracy in relation to the pattern recognition. In this article a Timepix [2] detector system has been used in the creation of a smart dosimeter for Alpha, Beta and Gamma radiation. When a radioactive particle hits the detector surface it generates charge clusters and those impacting upon the detector surface are read out and image processing algorithms are then used to classify each charge cluster. The individual clusters are calculated and as a result, the dosage for each type of radiation is given. In some cases, several particles can impact in roughly the same place, forming overlapping clusters. In order to handle this problem, a cluster separation method has been added to the pattern recognition algorithm. When the clusters have been separated, they are classified by shape and sorted into the correct type of radiation. The algorithms and methods used in this dosimeter have been developed so as to be simple and computationally effective, in order to enable implementation on a portable device. © 2012 IOP Publishing Ltd and SISSA.
|
|
| 5. |
- Lestinsky, M., et al.
(författare)
-
Physics book: CRYRING@ESR
- 2016
-
Ingår i: European Physical Journal: Special Topics. - : Springer Science and Business Media LLC. - 1951-6401 .- 1951-6355. ; 225:5, s. 797-882
-
Forskningsöversikt (refereegranskat)abstract
- The exploration of the unique properties of stored and cooled beams of highly-charged ions as provided by heavy-ion storage rings has opened novel and fascinating research opportunities in the realm of atomic and nuclear physics research. Since the late 1980s, pioneering work has been performed at the CRYRING at Stockholm (Abrahamsson et al. 1993) and at the Test Storage Ring (TSR) at Heidelberg (Baumann et al. 1988). For the heaviest ions in the highest charge-states, a real quantum jump was achieved in the early 1990s by the commissioning of the Experimental Storage Ring (ESR) at GSI Helmholtzzentrum für Schwerionenforschung (GSI) in Darmstadt (Franzke 1987) where challenging experiments on the electron dynamics in the strong field regime as well as nuclear physics studies on exotic nuclei and at the borderline to atomic physics were performed. Meanwhile also at Lanzhou a heavy-ion storage ring has been taken in operation, exploiting the unique research opportunities in particular for medium-heavy ions and exotic nuclei (Xia et al. 2002).
|
|
| 6. |
- Thiele, Illia, 1989, et al.
(författare)
-
Electron Beam Driven Generation of Frequency-Tunable Isolated Relativistic Subcycle Pulses
- 2019
-
Ingår i: Physical Review Letters. - 0031-9007 .- 1079-7114. ; 122
-
Tidskriftsartikel (refereegranskat)abstract
- © 2019 American Physical Society. We propose a novel scheme for frequency-tunable subcycle electromagnetic pulse generation. To this end a pump electron beam is injected into an electromagnetic seed pulse as the latter is reflected by a mirror. The electron beam is shown to be able to amplify the field of the seed pulse while upshifting its central frequency and reducing its number of cycles. We demonstrate the amplification by means of 1D and 2D particle-in-cell simulations. In order to explain and optimize the process, a model based on fluid theory is proposed. We estimate that using currently available electron beams and terahertz pulse sources, our scheme is able to produce millijoule-strong midinfrared subcycle pulses.
|
|
| 7. |
- Abata, E., et al.
(författare)
-
Study of energy response and resolution of the ATLAS barrel calorimeter to hadrons of energies from 20 to 350 GeV
- 2010
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier. - 0168-9002 .- 1872-9576 .- 0167-5087. ; 621:1-3, s. 134-150
-
Tidskriftsartikel (refereegranskat)abstract
- A fully instrumented slice of the ATLAS detector was exposed to test beams from the SPS (Super Proton Synchrotron) at CERN in 2004. In this paper, the results of the measurements of the response of the barrel calorimeter to hadrons with energies in the range 20-350 GeV and beam impact points and angles corresponding to pseudo-rapidity values in the range 0.2-0.65 are reported. The results are compared to the predictions of a simulation program using the Geant 4 toolkit. (C) 2010 Published by Elsevier B.V.
|
|
| 8. |
- Abat, E., et al.
(författare)
-
Photon reconstruction in the ATLAS Inner Detector and Liquid Argon Barrel Calorimeter at the 2004 Combined Test Beam
- 2011
-
Ingår i: Journal of Instrumentation. - 1748-0221. ; 6
-
Tidskriftsartikel (refereegranskat)abstract
- The reconstruction of photons in the ATLAS detector is studied with data taken during the 2004 Combined Test Beam, where a full slice of the ATLAS detector was exposed to beams of particles of known energy at the CERN SPS. The results presented show significant differences in the longitudinal development of the electromagnetic shower between converted and unconverted photons as well as in the total measured energy. The potential to use the reconstructed converted photons as a means to precisely map the material of the tracker in front of the electromagnetic calorimeter is also considered. All results obtained are compared with a detailed Monte-Carlo simulation of the test-beam setup which is based on the same simulation and reconstruction tools as those used for the ATLAS detector itself.
|
|
| 9. |
- Bengtsson, Lars, 1963
(författare)
-
Embedded Measurement Systems
- 2013
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The subject of Embedded Measurement Systems (EMS) is the merging of embedded systems and electrical measurement systems. This indicates that EMSs are hardware-software systems dedicated to measuring one or a few physical quantities. Applications are numerous; EMSs measure the temperature in refrigerators, freezers, irons, ovens and automobile combustion engines, they sense vibrations in tilt alarms and game consoles, they measure airflow in engines and ventilation systems, they measure shock impact in crash detectors and are used as shock and temperature loggers for transport goods, they measure air pressure in airplane cabins, humidity in air-conditioned environments, they measure liquid levels in fuel tanks, they detect smoke in fire alarms, they measure the viscosity of lubricant oil in engines, they measure the rotation speed of spinning wheels (in any engine), they measure torque in engines and are used as heart rate and ECG detectors in medicine etc. The commercial demand for ever cheaper products and worldwide environmental legislations force vendors to continuously look for more cost-efficient and less power-consuming solutions for their embedded measurement systems. This thesis is concerned most of all with the implementation of cost-efficient/low-power measurement systems in embedded controllers. This includes some novel ideas in voltage, time and resistance measurements with embedded controllers and it will demonstrate how these quantities, analog in nature, can be measured accurately and precisely by inherently digital embedded controllers.
|
|
| 10. |
- Abat, E., et al.
(författare)
-
Combined performance studies for electrons at the 2004 ATLAS combined test-beam
- 2010
-
Ingår i: Journal of Instrumentation. - : Institute of Physics (IOP). - 1748-0221. ; 5, s. P11006-
-
Tidskriftsartikel (refereegranskat)abstract
- In 2004 at the ATLAS (A Toroidal LHC ApparatuS) combined test beam, one slice of the ATLAS barrel detector (including an Inner Detector set-up and the Liquid Argon calorimeter) was exposed to particles from the H8 SPS beam line at CERN. It was the first occasion to test the combined electron performance of ATLAS. This paper presents results obtained for the momentum measurement p with the Inner Detector and for the performance of the electron measurement with the LAr calorimeter (energy E linearity and resolution) in the presence of a magnetic field in the Inner Detector for momenta ranging from 20 GeV/c to 100 GeV/c. Furthermore the particle identification capabilities of the Transition Radiation Tracker, Bremsstrahlungs-recovery algorithms relying on the LAr calorimeter and results obtained for the E/p ratio and a way how to extract scale parameters will be discussed.
|
|
