| 1. |
- Abdel Hady, Ahmed Wagih Abdallah, 1990, et al.
(författare)
-
In situ microstructural evolution of spruce wood during soda pulping using synchrotron X-ray tomography
- 2022
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 1437-434X .- 0018-3830. ; 76:7, s. 611-621
-
Tidskriftsartikel (refereegranskat)abstract
- A new laboratory reactor to perform in situ studies of structural changes in wood during soda pulping using synchrotron X-ray tomography is presented. The reactor is of recirculation type to provide stable reaction conditions and mimic the industrial situation. Experiments have been performed using this reactor in situ at a synchrotron microtomography beamline to provide sequences of 3D images from which measurement of wood cell wall thickness have been possible for the first time. The results showed that the cell wall thickness increased significantly in the early stage of pulping (<10 min), which is due to the transportation of cooking chemicals through the tracheids, resin channels and pits into the cell wall, which is swollen with the increased pH. Subsequently, the cell wall thickness reduces over the processing time up to 60 min with a high rate, which is inferred to be due to the dissolution and transport of lignin and hemicellulose from the secondary walls, allowing for better transportation of active chemicals deep through the cell wall layers. After 60 min processing, the cell wall thickness reduction rate reduced, as dissolution of lignin and hemicelluloses from the cell walls ceased, while the remaining dissolution occurs mainly at the middle lamella.
|
|
| 2. |
- Abdel Hady, Ahmed Wagih Abdallah, 1990, et al.
(författare)
-
Micro/nano-structural evolution in spruce wood during soda pulping
- 2021
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 1437-434X .- 0018-3830. ; 75:8, s. 754-764
-
Tidskriftsartikel (refereegranskat)abstract
- Alkaline delignification of wood tissue is the core of the global pulping technology and the most prominent large-scale separation of the main wood components. This work aims at improved understanding of the interplay between the topochemistry of alkaline pulping and the associated morphological changes. Morphology and chemical structure of partially soda-delignified wood chips were studied combining X-ray tomography (XRT), X-ray diffraction analysis and compositional characterization (lignin and carbohydrate content). The XRT studies of wet samples (providing 3D structural information without interfering drying effects), allowed observation of the cell wall separation as an increasing amount of lignin was removed with the increasing pulping time. Comparison between the microstructure of the surface and the central parts of the treated chips showed a more delignified microstructure at the surface, which highlights the dependence of the delignification process on the mass transport (hydroxide ions and lignin fragments) through the wood tissue. The crystallite size of cellulose increased in the <200> crystal planes during the early stage of pulping while there was little effect on the <110> plane.
|
|
| 3. |
- Adamopoulos, Stergios, et al.
(författare)
-
Tensile strength of handsheets prepared with macerated fibres from solid wood modified with cross-linking agents
- 2015
-
Ingår i: Holzforschung. - : Walter de Gruyter. - 0018-3830 .- 1437-434X. ; 69:8, s. 959-966
-
Tidskriftsartikel (refereegranskat)abstract
- This study was conducted to explain the tensile strength loss of wood due to the modification with 1,3-dimethylol-4,5-dihydroxyethyleneurea (DMDHEU) and glutaraldehyde (GA). Modified and control wood blocks were macerated to deliberate fibres, and handsheets were produced thereof. The nitrogen content of the fibres indicated that maceration removed the major proportions of DMDHEU. The stability of GA in wood during maceration was not assessed. Tensile strength determined at zero span (z-strength) and finite span (f-strength) was equal for the handsheets from DMDHEU-modified fibres and the control handsheets. The microscopic appearance of the tested finite-span paper strips from DMDHEU-modified fibres mainly indicated interfibre failure and did not differ from the fibre fracture mode of the control handsheets. In contrast, the z-strength of the handsheets from GA-modified fibres was lower than that of controls and decreased with increasing content of GA in the initial modified wood. The f-strength behaviour of the handsheets from GA-modified fibres was the opposite: it was higher than that of controls and increased with increasing GA content. The microscopic appearance of the rapture zones of the finite-span testing mainly indicated intrafibre failure for the GA-modified fibres. It was concluded that cross-linking is likely to be the major reason for tensile strength loss of GA- and DMDHEU-modified wood. In terms of DMDHEU-modified wood, the incrustation of the cell wall by the resin and the reduction in pliability could play an additional role.
|
|
| 4. |
- Ahlbom, Anders, 1993, et al.
(författare)
-
On the hydrothermal depolymerisation of kraft lignin using glycerol as a capping agent
- 2023
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 1437-434X .- 0018-3830. ; 77:3, s. 159-169
-
Tidskriftsartikel (refereegranskat)abstract
- Depolymerisation of kraft lignin under hydrothermal conditions was investigated at short residence times (1–12 min) with glycerol being used as a capping agent. The weight average molecular weight (M w) of the products decreased within the first minute of residence time, with the inter-unit ether linkages breaking accordingly. Furthermore, the M w of the product fractions decreased at increasing residence times, while the char yield increased. Short residence times thus appear to be beneficial for mitigating the formation of char. Also, addition of NaOH reduced the yield of char. Although the addition of glycerol caused a decrease in the M w of the products, it seemed to increase the yield of char and therefore might not be a suitable capping agent for kraft lignin depolymerisation.
|
|
| 5. |
- Ahlbom, Anders, 1993, et al.
(författare)
-
Towards understanding kraft lignin depolymerisation under hydrothermal conditions
- 2021
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 1437-434X .- 0018-3830. ; 76:1, s. 37-48
-
Tidskriftsartikel (refereegranskat)abstract
- Kraft lignin depolymerisation using hydrothermal liquefaction suffers from the formation of char, resulting in a decreased product yield as well as causing operational problems. While this may be mitigated by the addition of capping agents such as phenol and isopropanol, other reaction parameters, for example reaction time and temperature, are also important for the product yields. In this work, the effect of short reaction times on the hydrothermal liquefaction of kraft lignin in an alkaline water and isopropanol mixture was investigated at 1-12 min and 290 °C. The results show that there were swift initial reactions: the major ether bonds in the lignin were broken within the first minute of reaction, and the molecular weight of all product fractions was halved at the very least. Longer reaction times, however, do not cause as pronounced structural changes as the initial reaction, indicating that a recalcitrant carbon-carbon skeleton remained in the products. Nevertheless, the yields of both char and monomers increased slowly with increasing reaction time. The swift initial depolymerising reactions were therefore followed by slower repolymerisation as well as a slow formation of monomers and dimers, which calls for careful tuning of the reaction time.
|
|
| 6. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Uneven distribution of preservative in kiln-dried sapwood lumber of Scots pine : Impact of wood structure and resin allocation
- 2012
-
Ingår i: Holzforschung. - : Walter de Gruyter. - 0018-3830 .- 1437-434X. ; 66:2, s. 251-258
-
Tidskriftsartikel (refereegranskat)abstract
- Scots pine (Pinus sylvestris L.) sapwood lumber was collected after kiln drying and preservative treatment with Celcure AC 800 (a copper-amine wood preservative). Distribution of the preservative throughout the lumber was visually examined. Not all, but some samples showed specific localized areas without any preservative distribution throughout their entire length. Those samples were assessed further for anatomical properties, specifically in impregnated and unimpregnated areas. Additional study was conducted on the morphological nature and redistribution of lipophilic extractives using three different histochemical staining methods. Intrinsic wood properties – especially the frequency of axial resin canals and the percentage of canals blocked – were found to be responsible for the irregular distribution of the preservative. Furthermore, the inability to create continuous and frequent interstitial spaces due to the collapse of thin-walled ray cells throughout the lumber resulted in un-even distribution of preservatives. Staining techniques were useful to localize places with more or less abundance of extractives (e.g., fats) in impregnated and unimpregnated wood, which varied considerably. Histochemical observations revealed information pertaining to the kiln dry specific distribution and redistribution of extractives between the areas. Moreover, resin reallocation and modification in ray parenchyma and resin canals induced by kiln drying would be another reason for the impregnation anomalies.
|
|
| 7. |
- Ahrenstedt, Lage, et al.
(författare)
-
Paper dry strength improvement by xyloglucan addition: Wet-end application, spray coating and synergism with borate
- 2008
-
Ingår i: Holzforschung. - 0018-3830 .- 1437-434X. ; 62:1, s. 8-14
-
Tidskriftsartikel (refereegranskat)abstract
- The polysaccharide xyloglucan as a wet-end additive improves paper properties. In the present study, paper strength improvement was analysed for dry handsheets made from chemical, mechanical and recycled pulps coated with xyloglucan in a spray application. Results are compared with sheets made from the same pulps treated with xyloglucan in the wet-end. Kraft pulp handsheets of bleached hardwood and softwood showed significant improvements of tensile, tear and Z-strength by xyloglucan spray treatment versus wet-end application, whereas handsheets of de-inked and thermomechanical pulp were improved only slightly. In both wet-end and spray applications, the effect of xyloglucan addition was intimately related to the presence of non-cellulosic components on the fibre surface. Further strength improvements were obtained for chemical pulps by addition of borax to the spray solution, which were likely to be due to the formation of borate-mediated xyloglucan cross-links. Spray coating of xyloglucan, with or without borax, thus represents a potential new application of this polysaccharide to increase paper dry strength.
|
|
| 8. |
- Al-Rudainy, Basel, et al.
(författare)
-
Antisolvent precipitation of hemicelluloses, lignosulfonates and their complexes from ultrafiltrated spent sulfite liquor (SSL)
- 2018
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 1437-434X .- 0018-3830. ; 72:10, s. 839-850
-
Tidskriftsartikel (refereegranskat)abstract
- The possibility of precipitating high molecular weight (MW) softwood hemicelluloses has been investigated. Solids were precipitated from a sodium-based spent sulfite liquor with the anti-solvents acetone, ethanol and methanol and the effects of solute concentration, pH and temperature on the precipitation were studied. The product yield, degree of separation, MW and structure of the different fractions were determined using gravimetric analysis, high performance liquid chromatography (HPLC), ultraviolet–visible (UV-Vis) spectroscopy, size exclusion chromatography (SEC), and two-dimensional nuclear magnetic resonance (2D NMR). A direct correlation was found between the dielectric constant (also called relative permittivity) of the bulk solution and the yield of precipitants, based on which the separation of the solutes was predictable. The highest yield and degree of separation observed was an intercept around 76% with 47.5% acetone, which was the most efficient anti-solvent.
|
|
| 9. |
|
|
| 10. |
- Alfredsen, Gry, et al.
(författare)
-
Characterisation of Postia placenta colonisation during 36 weeks in acetylated southern yellow pine sapwood at three acetylation levels including genomic DNA and gene expression quantification of the fungus
- 2016
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 0018-3830 .- 1437-434X. ; 70:11, s. 1055-1065
-
Tidskriftsartikel (refereegranskat)abstract
- One way to protect timber in service against basidiomycete deterioration is by means of acetylation via reaction with acetic anhydride. The reason why acetylated wood (WAc) is resistant against decay fungi is still not exactly understood. The aim of this study was to contribute to this field of science, and Postia placenta colonisation after 4, 12, 20, 28 and 36 weeks was observed at three acetylation levels of Pinus spp. sapwood. Mass loss (ML) and wood moisture content (MC) data reflected the acetylation levels. The initial equilibrium MC (EMC) proved to be a good indicator of subsequent ML. Genomic DNA quantification showed P. placenta colonisation in all samples, also in samples where no ML were detectable. The number of expressed gene transcripts was limited, but the findings supported the results of previous studies: WAc seems to have some resistance against oxidative mechanisms, which are part of the metabolism of P. placenta. This leads to a delay in decay initiation, a delay in expression of genes involved in enzymatic depolymerisation, and a slower decay rate. The magnitudes of these effects are presented for each acetylation level. The data also imply that there is no absolute decay threshold at high acetylation levels, but instead a significant delay of decay initiation and a slower decay rate.
|
|
| 11. |
- Almkvist, Gunnar, et al.
(författare)
-
Prediction of tensile strength in iron-contaminated archaeological wood by FT-IR spectroscopy - a study of degradation in recent oak and Vasa oak
- 2016
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 0018-3830 .- 1437-434X. ; 70:9, s. 855-865
-
Tidskriftsartikel (refereegranskat)abstract
- Oak from the Swedish warship Vasa and recent oak that was aged after impregnation with iron(II) chloride has been analyzed by FT-IR spectroscopy and submitted to tensile strength testing. The aim was to investigate correlations between FT-IR bands in the fingerprint region, chemical degradation, and tensile strength in iron contaminated oak. The concentration of carboxylic functions increased and the acetyl groups in the hemicellulose fraction were decreasing as a function of degradation time. These changes are accompanied by reduced tensile strength and elevated content of oxalic acid (OA) in both Vasa wood and the impregnated recent oak samples. To evaluate the possibility to predict tensile strength from spectral data, chemometric modeling by partial least-squares (PLS) regression was applied. The strategy of repeated double cross validation (rdCV) allowed a realistic prediction of tensile strength. Overall, chemical changes and mechanical performances of iron contaminated wood are strongly correlated and thus FT-IR spectroscopy is suited to predict the strength properties of the degraded wood.
|
|
| 12. |
- Almlöf Ambjörnsson, Heléne, 1968-, et al.
(författare)
-
Enzyme pretreatment of dissolving pulp as a way to improve the following dissolution in NaOH/ZnO
- 2014
-
Ingår i: Holzforschung. - : Walter de Gruyter. - 0018-3830 .- 1437-434X. ; 68:4, s. 385-391
-
Tidskriftsartikel (refereegranskat)abstract
- The dissolution of a softwood dissolving pulp in a NaOH/ZnO system was improved by means of a three-stage pretreatment with an initial xylanase treatment, followed by an alkaline extraction, and finally an endoglucanase stage. The solubility of the pulp increased from 29% to 81%, although the crystallinity and the specific surface area of the pulp did not change during the enzymatic treatment.
|
|
| 13. |
- Almlöf, Heléne, 1968-, et al.
(författare)
-
The influence of extended mercerization on some properties of carboxymethyl cellulose (CMC)
- 2012
-
Ingår i: Holzforschung. - 0018-3830 .- 1437-434X. ; 66, s. 21-27
-
Tidskriftsartikel (refereegranskat)abstract
- Carboxymethyl cellulose (CMC) is produced commercially in a two stage process consisting of a mercerization stage in which the pulp is treated with alkali in a water alcohol solution and a second etherification stage whereby monochloro-acetic acid is added to the pulp slurry. In this study, the influence of the conditions of an extended mercerization stage was evaluated on the etherification stage concerning the degree of substitution (DS) and the filterability of the resulting CMC. The parameters studied were: (1) the ratio of cellulose I and cellulose II in the original pulp, (2) the concentration of alkali, (3) the temperature and (4) the retention time in the mercerization stage. The DS results indicate that the NaOH concentration in the mercerization stage is the most important among the parameters studied. When the NaOH concentration in the mercerization stage was high (27.5%), cellulose II showed a lower reactivity than cellulose I with respect to the DS obtained in the resulting CMC. The results from the filtration ability of CMC water solutions are interpreted that the amount of cellulose II in the original pulp and the temperature has a negative influence, while the NaOH concentration in the mercerization stage has a positive influence on the filtration ability. Retention time between 1 h–48 h in the mercerization stage had no effect on the DS or the filtration value. The filtration ability was assumed to be highly influenced by the presence of poorly reacted cellulose segments. The CMC samples with the lowest filtration ability at a given DS can be assumed to have the highest degree of unevenly substituted segments.
|
|
| 14. |
- Amiandamhen, Stephen, 1983-, et al.
(författare)
-
Calcium phosphate bonded wood and fiber composite panels : production and optimization of panel properties
- 2017
-
Ingår i: Holzforschung. - Germany : Walter de Gruyter. - 0018-3830 .- 1437-434X. ; 71:9, s. 725-732
-
Tidskriftsartikel (refereegranskat)abstract
- The development of phosphate bonded composites with properties comparable with those of current Portland cement bonded products has been investigated. More precisely, the focus of the study was the optimization of calcium phosphate cements in combination with wood processing residues slash pine (Pinus elliottii Engelm.) planer shavings, Black wattle (Acacia mearnsii De Wild.) residues, Blue gum (Eucalyptus globulus Labill.) residues, hemp (Cannabis Sativa L.) hurds and dried crushed sugarcane bagasse (Saccharum officinarum L.) as well as pulp mill sludge and waste paper. A central composite design (CCD) for the response surface methodology (RSM) was applied for selection of the proper parameters. Mechanical tests were conducted on the composite products and the effect of the processing variables was evaluated based on the Pareto analysis of variance. The density of the wood-based panels ranged from 0.68 to 1.21 g cm−3, that of the agricultural fibers from 0.59 to 1.15 g cm−3 and that of the paper pulp panels from 0.81 to 1.21 g cm−3. The modulus of elasticity (MOE) data of the panels ranged from 1.63 to 4.92 MPa for wood, from 0.37 to 3.28 MPa for agricultural fibers and from 0.65 to 3.87 MPa for paper-pulp-based fibers. The physical properties of the composite products met the requirements for Portland-cement-bonded particleboards (EN 634-2, 2007).
|
|
| 15. |
- Anugwom, Ikenna, et al.
(författare)
-
Treating birch wood with a switchable 1,8-diazabicyclo-[5.4.0]-undec-7-ene-glycerol carbonate ionic liquid
- 2012
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 0018-3830 .- 1437-434X. ; 66:7, s. 809-815
-
Tidskriftsartikel (refereegranskat)abstract
- The suitability of a new switchable ionic liquid (SIL) has been investigated as a solvent for fractionation of lignocellulosic materials. SIL was prepared from inexpensive chemicals, e. g., glycerol, CO2, and 1,8-diazabicyclo-[5.4.0]-undec-7-ene (DBU). Fresh Nordic birch wood (B. pendula) was treated with the SIL for a time period of 1-5 days at 100 degrees C and under atmospheric pressure. Upon SIL treatment, at best, 57 % of the hemicelluloses were dissolved and 50 % of lignins were dissolved from the native birch. The slightly fibrillated SIL treated chips contained about 55 % cellulose. Up to 76 % of the recovered species removed from the spent SIL liquor was originating from hemicelluloses, mainly from xylan. The spent SILs were reused for fresh wood dissolution in four consecutive cycles and each time the wood dissolution efficiency was similar. SILs could offer affordable (easy-to-synthesize) solvent systems for partial elimination of hemicelluloses and lignin from wood. SILs can also be prepared in-situ and on-site.
|
|
| 16. |
- Areskogh, Dimitri, et al.
(författare)
-
Oxidative polymerisation of models for phenolic lignin end-groups by laccase
- 2010
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 0018-3830 .- 1437-434X. ; 64:1, s. 21-34
-
Tidskriftsartikel (refereegranskat)abstract
- The redox enzyme laccase can lead to cross-linking of lignin molecules by oxidising phenolic end groups to resonance-stabilised radicals that can undergo radical coupling to form covalent bonds. This property has potential for many technical applications. However, laccase treatment can also lead to degradation. Experiments were performed with two laccases of different oxidation potential and pH and temperature optima. The predominant reaction following laccase oxidation is the formation of 5-5' and 4-O-5' bonds. If the 5-position is blocked, other reactions occur, including coupling of the 1-position and oxidation of the a-position, which aggravates cross-linking of different lignin molecules. The product profile generated by the two laccases is somewhat different, mainly because of the different pH rather than differences in enzyme activity. Reaction mechanisms and the technical and biological significance of the results are discussed.
|
|
| 17. |
- Backstrom, Marie, et al.
(författare)
-
Influence of chip presteaming conditions on kraft pulp composition and properties
- 2016
-
Ingår i: Holzforschung. - : Walter de Gruyter. - 0018-3830 .- 1437-434X. ; 70:5, s. 393-399
-
Tidskriftsartikel (refereegranskat)abstract
- Presteaming is a well-established technique in pulp mills, which improves cooking liquor impregnation by removing air from within and between chips. The aim of the study was to investigate how conditions during steaming affect the subsequent kraft cook and properties of the obtained pulp. It was found that higher pressure and temperature during chip presteaming led to increased degradation and dissolution of hemicelluloses. Lower refinability and tensile index was obtained for pulps cooked after presteaming at high pressure and for a long time.
|
|
| 18. |
- Bader, Thomas K., et al.
(författare)
-
Changes in microstructure and stiffness of Scots pine (Pinus sylvestris L) sapwood degraded by Gloeophyllum trabeum and Trametes versicolor Part II : Anisotropic stiffness properties
- 2012
-
Ingår i: Holzforschung. - 0018-3830 .- 1437-434X. ; 66:2, s. 199-206
-
Tidskriftsartikel (refereegranskat)abstract
- Fungal decay considerably affects the macroscopic mechanical properties of wood as a result of modifications and degradations in its microscopic structure. While effects on mechanical properties related to the stem direction are fairly well understood, effects on radial and tangential directions (transverse properties) are less well investigated. In the present study, changes of longitudinal elastic moduli and stiffness data in all anatomical directions of Scots pine (Pinus sylvestris) sapwood which was degraded by Gloeophyllum trabeum (brown rot) and Trametes versicolor (white rot) for up to 28 weeks have been investigated. Transverse properties were found to be much more deteriorated than the longitudinal ones. This is because of the degradation of the polymer matrix between the cellulose microfibrils, which has a strong effect on transverse stiffness. Longitudinal stiffness, on the other hand, is mainly governed by cellulose microfibrils, which are more stable agains fungal decay. G. trabeum (more active in earlywood) strongly weakens radial stiffness, whereas T. versicolor (more active in latewood) strongly reduces tangential stiffness. The data in terms of radial and tangential stiffnesses, as well as the corresponding anisotropy ratios, seem to be suitable as durability indicators of wood and even allow conclusions to be made on the degradation mechanisms of fungi.
|
|
| 19. |
- Bader, Thomas K., et al.
(författare)
-
Microstructure and stiffness of Scots pine (Pinus sylvestris L) sapwood degraded by Gloeophyllum trabeum and Trametes versicolor Part I : Changes in chemical composition, density and equilibrium moisture content
- 2012
-
Ingår i: Holzforschung. - 0018-3830 .- 1437-434X. ; 66:2, s. 191-198
-
Tidskriftsartikel (refereegranskat)abstract
- Fungal degradation alters the microstructure of wood and its physical and chemical properties are also changed. While these changes are well investigated as a function of mass loss, mass density loss and changes in equilibrium moisture content are not well elucidated. The physical and chemical alterations are crucial when linking microstructural characteristics with macroscopic mechanical properties. In the present article, a consistent set of physical, chemical and mechanical characteristics is presented, which were measured on the same sample before and after fungal degradation. In the first part of this two-part contribution, elucidating microstructure/stiffness-relationships of degraded wood, changes in physical and chemical data are presented, which were collected from specimens of Scots pine (Pinus sylvestris) sapwood degraded by Gloeophyllum trabeum (brown rot) and Trametes versicolor (white rot) for up to 28 weeks degradation time. A comparison of mass loss with corresponding mass density loss demonstrated that mass loss entails two effects: firstly, a decrease in sample size (more pronounced for G. trabeum), and secondly, a decrease of mass density within the sample (more pronounced for T. versicolor). These two concurrent effects are interrelated with sample size and shape. Hemicelluloses and cellulose are degraded by G. trabeum, while T. versicolor was additionally able to degrade lignin. In particular because of the breakdown of hemicelluloses and paracrystalline parts of cellulose, the equilibrium moisture content of degraded samples is lower than that in the initial state.
|
|
| 20. |
- Baumberger, Stephanie, et al.
(författare)
-
Molar mass determination of lignins by size-exclusion chromatography : towards standardisation of the method
- 2007
-
Ingår i: Holzforschung. - 0018-3830 .- 1437-434X. ; 61:4, s. 459-468
-
Tidskriftsartikel (refereegranskat)abstract
- The reactivity and physicochemical properties of lignins are partly governed by their molar mass distribution. The development of reliable standard methods for determination of the molar mass distribution is not only relevant for designing technical lignins for specific applications, but also for monitoring and elucidating delignification and pulping processes. Size-exclusion chromatography (SEC) offers many advantages, such as wide availability, short analysis time, low sample demand, and determination of molar mass distribution over a wide range. A collaborative study has been undertaken within the Eurolignin European thematic network to standardise SEC analysis of technical lignins. The high-molar-mass fraction of polydisperse lignins was shown to be the main source of intra- and interlaboratory variations, depending on the gel type, elution solvent, detection mode, and calculation strategy. The reliability of two widespread systems have been tested: one based on alkali and a hydrophilic gel (e.g., TSK Toyopearl gel) and the other based on THF as solvent and polystyrene-based gels (e.g., Styragel). A set of practical recommendations has been deduced.
|
|
| 21. |
- Bengtsson, Andreas, et al.
(författare)
-
Improved yield of carbon fibres from cellulose and kraft lignin
- 2018
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 0018-3830 .- 1437-434X. ; 72:12, s. 1007-1016
-
Tidskriftsartikel (refereegranskat)abstract
- To meet the demand for carbon-fibre-reinforced composites in lightweight applications, cost-efficient processing and new raw materials are sought for. Cellulose and kraft lignin are each interesting renewables for this purpose due to their high availability. The molecular order of cellulose is an excellent property, as is the high carbon content of lignin. By co-processing cellulose and lignin, the advantages of these macromolecules are synergistic for producing carbon fibre (CF) of commercial grade in high yields. CFs were prepared from precursor fibres (PFs) made from 70:30 blends of softwood kraft lignin (SW-KL) and cellulose by dry-jet wet spinning with the ionic liquid (IL) 1-ethyl-3-methylimidazolium acetate ([EMIm][OAc]) as a solvent. In focus was the impact of the molecular mass of lignin and the type of cellulose source on the CF yield and properties, while membrane-filtrated kraft lignin and cellulose from dissolving kraft pulp and fully bleached paper-grade SW-KP (kraft pulp) served as sources. Under the investigated conditions, the yield increased from around 22% for CF from neat cellulose to about 40% in the presence of lignin, irrespective of the type of SW-KL. The yield increment was also higher relative to the theoretical one for CF made from blends (69%) compared to those made from neat celluloses (48-51%). No difference in the mechanical properties of the produced CF was observed.
|
|
| 22. |
- Bengtsson, Charlotte, et al.
(författare)
-
Bending creep of high-temperature dried spruce timber
- 2003
-
Ingår i: Holzforschung. - 0018-3830 .- 1437-434X. ; 57:1, s. 95-100
-
Tidskriftsartikel (refereegranskat)abstract
- In this paper, bending creep test results from high-temperature (HT) dried Norway Spruce timber are presented. The results are compared with creep tests of conventional low-temperature (LT) dried timber. The HT drying was performed at 115°C and the LT drying was performed at 70°C. The creep tests were performed in a varying climate with 20°C and 30–90% relative humidity. A total number of 24 specimens, 45 × 70 × 1100 mm, were loaded in bending during approximately 240 days. Both the HT-dried and the LT-dried material were cut from the same four trees to have as equal raw material as possible for the two drying methods. The results show smaller bending creep deformations of HT-dried timber (approximately 30%) as compared to the LT-dried timber. The variation in magnitude of creep for HT-dried timber was equal to or smaller than for LT-dried timber. Additionally, the variation in deformation between the moisture cycles was smaller for HT-dried timber. These observations indicate a less pronounced mechano-sorptive effect for HT-dried timber. The free shrinkage in the grain direction was significantly smaller for the HT-dried material than for the LT-dried material.
|
|
| 23. |
- Bengtsson, Jenny, 1990, et al.
(författare)
-
Mass transport and yield during spinning of lignin-cellulose carbon fiber precursors
- 2019
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 1437-434X .- 0018-3830. ; 73:5, s. 509-516
-
Tidskriftsartikel (refereegranskat)abstract
- Lignin, a substance considered as a residue in biomass and ethanol production, has been identified as a renewable resource suitable for making inexpensive carbon fibers (CFs), which would widen the range of possible applications for light-weight CFs reinforced composites. Wet spinning of lignin-cellulose ionic liquid solutions is a promising method for producing lignin-based CFs precursors. However, wet-spinning solutions containing lignin pose technical challenges that have to be solved to enable industrialization. One of these issues is that a part of the lignin leaches into the coagulation liquid, which reduces yield and might complicate solvent recovery. In this work, the mass transport during coagulation is studied in depth using a model system and trends are confirmed with spinning trials. It was discovered that during coagulation, efflux of ionic liquid is not hindered by lignin concentration in solution and the formed cellulose network will enclose soluble lignin. Consequently, a high total concentration of lignin and cellulose in solution is advantageous to maximize yield. This work provides a fundamental understanding on mass transport during coagulation of lignin-cellulose solutions, crucial information when designing new solution-based fiber forming processes.
|
|
| 24. |
- Bengtsson, Jenny, et al.
(författare)
-
Preventing fiber-fiber adhesion of lignin-cellulose precursors and carbon fibers with spin finish application
- 2023
-
Ingår i: Holzforschung. - : De Gruyter Open Ltd. - 0018-3830 .- 1437-434X. ; 77, s. 648-
-
Tidskriftsartikel (refereegranskat)abstract
- Adhesion of fibers within a spun tow, including carbon fibers and precursors, is undesirable as it may interrupt the manufacturing process and entail inferior fiber properties. In this work, softwood kraft lignin was used together with a dissolving pulp to spin carbon fiber precursors. Lignin-cellulose precursors have previously been found to be prone to fiber fusion, both post-spinning and during carbon fiber conversion. In this study, the efficiency of applying different kinds of spin finishes, with respect to rendering separable precursors and carbon fibers, has been investigated. It was found that applying a cationic surfactant, and to a similar extent a nonionic surfactant, resulted in well separated lignin-cellulose precursor tows. Furthermore, the fiber separability after carbon fiber conversion was evaluated, and notably, precursors treated with a silicone-based spin finish generated the most well-separated carbon fibers. The underlying mechanism of fiber fusion post-spinning and converted carbon fibers is discussed.
|
|
| 25. |
- Bengtsson, Peter, 1974-, et al.
(författare)
-
Evaluation of hydrocarbon emissions from heart- and sapwood of Scots pine using a laboratory-scale wood drier
- 2004
-
Ingår i: Holzforschung. - : Walter de Gruyter. - 1437-434X .- 0018-3830. ; 58:6, s. 660-665
-
Tidskriftsartikel (refereegranskat)abstract
- The subject of study is the emission of Volatile Organic Compounds (VOC) during the drying of wood. Heartwood and sapwood from Scots pine were dried at different temperatures (50, 70 and 90°C) in a laboratory kiln. The sampling method, Solid Phase Microextraction was used to collect the different volatile organic compounds during the drying. The gas chromatograph and mass spectrometer was used to identify and quantify the organic matter. The total hydrocarbons were measured with a flame ionization detector. Primarily, different monoterpenes were released during the drying process. 3-carene and α-pinene were most common and were also analytically quantified. The diterpene, pimaral, was found in an estimated large amount in the later stage of the drying process but was not exactly quantified. Large differences in both release behaviour and total amount of released hydrocarbon between heart- and sapwood were obtained. Emissions of VOC from heartwood were of a magnitude approximately three times higher than that from sapwood.
|
|
