| 1. |
- Almehed, Sverker, et al.
(författare)
-
A Silicon-Tungsten Electromagnetic Calorimeter for LEP
- 1991
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 305:2, s. 320-330
-
Tidskriftsartikel (refereegranskat)abstract
- This report describes a silicon-tungsten electromagnetic calorimeter used to determine some beam properties and luminosity in the DELPHI experiment at LEP. The polar angular range covered by this detector is 5–8 mrad, which allows the detection of a Bhabha rate about 10 times the rate of produced Z particles at the peak cross section.
|
|
| 2. |
- Andersson, Åke, et al.
(författare)
-
Beam profile measurements at MAX
- 1995
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 364:1, s. 4-12
-
Tidskriftsartikel (refereegranskat)abstract
- An electron beam profile monitor system is described. It utilizes the visible bending magnet synchrotron radiation (SR) to form an image of the beam. A model for calculating diffraction and depth of field effects is introduced. Assuming a Gaussian distributed electron beam, the relation between beam image size and actual beam size is then calculated with this model, for a number of practical measuring situations. In a series of measurements at the MAX I electron storage ring at a current of 1 mA, the beam image size has been measured for these calculated situations. The measured values are presented, and their behaviour is in good agreement with the model. With this model the horizontal and vertical rms beam sizes were determined to σx = (203 ± 3) μm and σy = (19 ± 3) μm respectively. The corresponding vertical emittance is approximately 0.05 nm rad.
|
|
| 3. |
- Andersson, Åke, et al.
(författare)
-
Experiences with the narrow gap undulator at MAX-lab
- 1995
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 362:2-3, s. 586-591
-
Tidskriftsartikel (refereegranskat)abstract
- An undulator with short poles (period 24 mm) and extremely narrow gap (magnet gap 7.7 mm) using a squeezable vacuum chamber has been installed and is in operation at the MAX-lab 550 MeV storage ring. The device operates with a vacuum chamber aperture down to 6.2 mm. The behaviour of the storage ring concerning lifetime, emittance, tune shift and closed orbit is well described by conventional models. We present here the design of the device, the influence on the storage ring and the spectral characteristics, as well as comparison with expected theoretical results and an overview of the activities at the beam line.
|
|
| 4. |
- Andersson, Åke, et al.
(författare)
-
Positron production for ESRF
- 1988
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 267:1, s. 15-21
-
Tidskriftsartikel (refereegranskat)abstract
- In this report, we first discuss some different pre-injector possibilities for the ESRF booster synchrotron, using estimated machine performances. We then focus on the commercially available linac schemes carrying out more detailed calculations. We also look into the possibility of recyling the particles through the linacs.
|
|
| 5. |
- Andersson, Åke, et al.
(författare)
-
The MAX II synchrotron radiation storage ring
- 1994
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 343:2-3, s. 644-649
-
Tidskriftsartikel (refereegranskat)abstract
- A 1.5 GeV third generation storage ring optimised for the VUV and soft X-ray spectral region is currently being built at MAX-lab. The magnet lattice, ring architecture and production choices are optimised to fit within rather tight boundary conditions without sacrificing performance. In this paper, the magnet lattice, light characteristics, injection and technical solutions for the ring are presented.
|
|
| 6. |
- Da Via, C, et al.
(författare)
-
Lightwave Analogue Links For LHC Detector Front-ends
- 1994
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 344:1, s. 199-211
-
Tidskriftsartikel (refereegranskat)abstract
- The requirements on optical links for transferring analog and digital signals from the detector front-ends to the readout electronics at future high-luminosity colliders are reviewed. The advantages of external modulation techniques are discussed. An outline is given of the the R&D programme recently started at CERN by a collaboration involving high-energy physics institutes, optoelectronics research laboratories and industry, in order to develop electro-optic intensity modulator arrays, particularly for analogue applications, and to investigate the feasibility of volume production. The design of multichannel demonstrators in lithium niobate and III-V semiconductor technology is described. Preliminary results of the performance measurements are presented.
|
|
| 7. |
- Hedin, Lars
(författare)
-
Properties of electron self-energies and their role in electron spectroscopies
- 1991
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; A308:1-2, s. 169-177
-
Tidskriftsartikel (refereegranskat)abstract
- The GW approximation for the self-energy connected with the one-electron Green's function has been very successful in predicting band structures for a large class of semiconductors and insulators. The physical basis for this approximation and general features of its nonlocality are discussed, as well as possible improvements. Besides quasiparticle energies the self-energy also gives the intrinsic part of the photoelectron spectrum. In general, however, a full description of experimental spectra measured with synchrotron radiation, such as photoemission, Auger spectra and EXAFS, cannot be given by the one-electron Green's function. A new theoretical approach to synchrotron radiation spectroscopies is given in terms of the coupling functions involved in the GW approximation and on-the-energy-shell one-electron Green's functions.(14 refs)
|
|
| 8. |
- Scheffel, Jan, 1954-
(författare)
-
Neutron Spectra from Beam-Heated Fusion Plasmas
- 1984
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576 .- 0167-5087. ; 224:3, s. 519-531
-
Tidskriftsartikel (refereegranskat)abstract
- The spectra of fusion neutrons emerging from a deuterium-beam heated deuterium or tritium plasma yield information of both the bulk plasma and of the beam slowing down. A computer code has been developed to model plasma-plasma (p-p), beam-plasma (b-p) and beam-beam (b-b) interaction for the case of a single or several co-directed beams. It is found that for a high-temperature plasma (T ⪢ 1 keV) b-b interaction is negligible due to the low associated neutron emission. p-p neutron spectra reflect the bulk ion plasma temperature and density as well as toroidal rotational velocity. b-p spectra shifts and broadenings are sensitive to beam injection geometry and deposition, beam energy, ion and electron temperature, toroidal rotation and the density of neutrals. The mixing of full energy beam neutrals with half- and third-energy components has only a slight impact on the neutron spectrum when the beam power is held constant. For a JET-like Tokamak (D → D, beam power 5 MW, beam energy 160 keV) it is further found that for T ⪡ 8 keV the b-p neutron flux dominates, whereas for T ⪢ 8 keV the p-p flux dominates.
|
|
| 9. |
- Abat, E., et al.
(författare)
-
Study of the response of the ATLAS central calorimeter to pions of energies from 3 to 9 GeV
- 2009
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002 .- 1872-9576. ; 607:2, s. 372-386
-
Tidskriftsartikel (refereegranskat)abstract
- A fully instrumented slice of the ATLAS central detector was exposed to test beams from the SPS (Super Proton Synchrotron) at CERN in 2004. in this paper, the response of the central calorimeters to pions with energies in the range between 3 and 9 GeV is presented. The linearity and the resolution of the combined calorimetry (electromagnetic and hadronic calorimeters) was measured and compared to the prediction of a detector simulation program using the toolkit Geant 4. (C) 2009 Elsevier B.V. All rights reserved.
|
|
| 10. |
- Abata, E., et al.
(författare)
-
Study of energy response and resolution of the ATLAS barrel calorimeter to hadrons of energies from 20 to 350 GeV
- 2010
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier. - 0168-9002 .- 1872-9576 .- 0167-5087. ; 621:1-3, s. 134-150
-
Tidskriftsartikel (refereegranskat)abstract
- A fully instrumented slice of the ATLAS detector was exposed to test beams from the SPS (Super Proton Synchrotron) at CERN in 2004. In this paper, the results of the measurements of the response of the barrel calorimeter to hadrons with energies in the range 20-350 GeV and beam impact points and angles corresponding to pseudo-rapidity values in the range 0.2-0.65 are reported. The results are compared to the predictions of a simulation program using the Geant 4 toolkit. (C) 2010 Published by Elsevier B.V.
|
|
| 11. |
- Acharya, S, et al.
(författare)
-
The ALICE transition radiation detector: Construction, operation, and performance
- 2018
-
Ingår i: Nuclear Instruments and Methods in Physics Research, Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 881, s. 88-127
-
Tidskriftsartikel (refereegranskat)abstract
- The Transition Radiation Detector (TRD) was designed and built to enhance the capabilities of the ALICE detector at the Large Hadron Collider (LHC). While aimed at providing electron identification and triggering, the TRD also contributes significantly to the track reconstruction and calibration in the central barrel of ALICE. In this paper the design, construction, operation, and performance of this detector are discussed. A pion rejection factor of up to 410 is achieved at a momentum of 1 GeV/c in p-Pb collisions and the resolution at high transverse momentum improves by about 40% when including the TRD information in track reconstruction. The triggering capability is demonstrated both for jet, light nuclei, and electron selection. © 2017 CERN for the benefit of the ALICE Collaboration.
|
|
| 12. |
- Adler, Jan-Olof, et al.
(författare)
-
The upgraded photon tagging facility at the MAX IV Laboratory
- 2013
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 715, s. 1-10
-
Tidskriftsartikel (refereegranskat)abstract
- A description is given of the upgraded photon tagging facility at the MAX IV Laboratory. Two magnetic spectrometers are used to momentum analyze post-bremsstrahlung electrons. The tagged photon range extends from 10 to 180 MeV with an energy resolution of about 300 keV. The system has been operated at rates up to 4 x 10(6) photons s(-1) MeV (-1). Different diagnostic tools are described as well as the experimental program.
|
|
| 13. |
- Aggarwal, M.M, et al.
(författare)
-
Particle identification studies with a full-size 4-GEM prototype for the ALICE TPC upgrade
- 2018
-
Ingår i: Nuclear Instruments and Methods in Physics Research, Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 903, s. 215-223
-
Tidskriftsartikel (refereegranskat)abstract
- A large Time Projection Chamber is the main device for tracking and charged-particle identification in the ALICE experiment at the CERN LHC. After the second long shutdown in 2019/20, the LHC will deliver Pb beams colliding at an interaction rate of about 50 kHz, which is about a factor of 50 above the present readout rate of the TPC. This will result in a significant improvement on the sensitivity to rare probes that are considered key observables to characterize the QCD matter created in such collisions. In order to make full use of this luminosity, the currently used gated Multi-Wire Proportional Chambers will be replaced. The upgrade relies on continuously operated readout detectors employing Gas Electron Multiplier technology to retain the performance in terms of particle identification via the measurement of the specific energy loss by ionization dE/dx. A full-size readout chamber prototype was assembled in 2014 featuring a stack of four GEM foils as an amplification stage. The performance of the prototype was evaluated in a test beam campaign at the CERN PS. The dE/dx resolution complies with both the performance of the currently operated MWPC-based readout chambers and the challenging requirements of the ALICE TPC upgrade program. Detailed simulations of the readout system are able to reproduce the data. © 2018 Elsevier B.V.
|
|
| 14. |
- Ainsworth, Robert, et al.
(författare)
-
The influence of parasitic modes on beam dynamics for the European spallation source linac
- 2014
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 734, s. 95-100
-
Tidskriftsartikel (refereegranskat)abstract
- The European Spallation Source (ESS) linac will consist of three families of superconducting RE cavities to accelerate protons to a final beam energy of 2.5 GeV for collision with the target. Beam induced HOMs in these cavities may drive the beam unstable and increase the cryogenic load, severely limiting the operation of the linac. The effect of these modes on the beam quality is investigated in detail using a numerical code dedicated to beam-HOM interaction. (C) 2012 Elsevier B.V. All rights reserved.
|
|
| 15. |
- Akkoyun, S., et al.
(författare)
-
AGATA - Advanced GAmma Tracking Array
- 2012
-
Ingår i: Nuclear Instruments and Methods in Physics Research, Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. - : Elsevier BV. - 0168-9002 .- 0167-5087 .- 1872-9576. ; 668, s. 26-58
-
Tidskriftsartikel (refereegranskat)abstract
- The Advanced GAmma Tracking Array (AGATA) is a European project to develop and operate the next generation γ-ray spectrometer. AGATA is based on the technique of γ-ray energy tracking in electrically segmented high-purity germanium crystals. This technique requires the accurate determination of the energy, time and position of every interaction as a γ ray deposits its energy within the detector volume. Reconstruction of the full interaction path results in a detector with very high efficiency and excellent spectral response. The realisation of γ-ray tracking and AGATA is a result of many technical advances. These include the development of encapsulated highly segmented germanium detectors assembled in a triple cluster detector cryostat, an electronics system with fast digital sampling and a data acquisition system to process the data at a high rate. The full characterisation of the crystals was measured and compared with detector- response simulations. This enabled pulse-shape analysis algorithms, to extract energy, time and position, to be employed. In addition, tracking algorithms for event reconstruction were developed. The first phase of AGATA is now complete and operational in its first physics campaign. In the future AGATA will be moved between laboratories in Europe and operated in a series of campaigns to take advantage of the different beams and facilities available to maximise its science output. The paper reviews all the achievements made in the AGATA project including all the necessary infrastructure to operate and support the spectrometer. © 2011 Elsevier B.V. All rights reserved.
|
|
| 16. |
- Alcorn, J, et al.
(författare)
-
Basic instrumentation for Hall A at Jefferson Lab
- 2004
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 522:3, s. 294-346
-
Tidskriftsartikel (refereegranskat)abstract
- The instrumentation in Hall A at the Thomas Jefferson National Accelerator Facility was designed to study electro-and photo-induced reactions at very high luminosity and good momentum and angular resolution for at least one of the reaction products. The central components of Hall A are two identical high resolution spectrometers, which allow the vertical drift chambers in the focal plane to provide a momentum resolution of better than 2 x 10(-4). A variety of Cherenkov counters, scintillators and lead-glass calorimeters provide excellent particle identification. The facility has been operated successfully at a luminosity well in excess of 10(38) CM-2 s(-1). The research program is aimed at a variety of subjects, including nucleon structure functions, nucleon form factors and properties of the nuclear medium. (C) 2003 Elsevier B.V. All rights reserved.
|
|
| 17. |
- Alkhazov, GD, et al.
(författare)
-
SPES4-pi: installation for exclusive study of nuclear reactions
- 2005
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 551:2-3, s. 290-311
-
Tidskriftsartikel (refereegranskat)abstract
- The paper describes the spectrometric system "SPES4-pi" used at the National Laboratory Saturne (CE Saclay, France) for the exclusive study of the baryon resonance excitation in inelastic alpha and d scattering on the proton, as well as coherent pion production in charge exchange reactions. The system consists of the magnetic spectrometer SPES4 and two wide-aperture position-sensitive detector arrays, equipped with wire chambers and scintillator hodoscopes, installed around a large-gap C-shape dipole magnet.
|
|
| 18. |
- Alme, J., et al.
(författare)
-
The ALICE TPC, a large 3-dimensional tracking device with fast readout for ultra-high multiplicity events
- 2010
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 622:1, s. 316-367
-
Tidskriftsartikel (refereegranskat)abstract
- The design, construction, and commissioning of the ALICE Time-Projection Chamber (TPC) is described. It is the main device for pattern recognition, tracking, and identification of charged particles in the ALICE experiment at the CERN LHC. The TPC is cylindrical in shape with a volume close to 90 m(3) and is operated in a 0.5T solenoidal magnetic field parallel to its axis. In this paper we describe in detail the design considerations for this detector for operation in the extreme multiplicity environment of central Pb-Pb collisions at LHC energy. The implementation of the resulting requirements into hardware (field cage, read-out chambers, electronics), infrastructure (gas and cooling system, laser-calibration system), and software led to many technical innovations which are described along with a presentation of all the major components of the detector, as currently realized. We also report on the performance achieved after completion of the first round of stand-alone calibration runs and demonstrate results close to those specified in the TPC Technical Design Report. (C) 2010 CERN for the benefit of the ALICE collaboration. Published by Elsevier B.V. All rights reserved.
|
|
| 19. |
- Alvarez-Pol, H., et al.
(författare)
-
Performance analysis for the CALIFA Barrel calorimeter of the (RB)-B-3 experiment
- 2014
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 767, s. 453-466
-
Tidskriftsartikel (refereegranskat)abstract
- The CALIFA calorimeter is an advanced detector for gamma rays and light charged particles, accordingly optimized for the demanding requirements of the physics programme proposed for the (RB)-B-3 facility at FAIR. The multipurpose character of CALIFA is required to fulfil challenging demands in energy resolution (5-6% at 1 MeV for gamma rays) and efficiency. Charged particles, e.g. protons of energies up to 320 MeV in the Barrel section, should also be identified with an energy resolution better to 1%. CALIFA is divided into two well-separated sections: a "Forward EndCap" and a cylindrical "Barrel" covering an angular range from 43.2 degrees to 140.3 degrees. The Barrel section, based on long CsI(Tl) pyramidal frustum crystals coupled to large area avalanche photodiodes (LAAPDs), attains the requested high efficiency for calorimetric purposes. The construction of the CALIFA Demonstrator, comprising 20% of the total detector, has already been initiated, and commissioning experiments are expected for 2014. The assessment of the capabilities and expected performance of the detector elements is a crucial step in their design, along with the prototypes evaluation. For this purpose, the Barrel geometry has been carefully implemented in the simulation package R3BRoot, including easily variable thicknesses of crystal wrapping and carbon fibre supports. A complete characterization of the calorimeter response (including efficiency, resolution, evaluation of energy and reconstruction losses) under different working conditions, with several physics cases selected to probe the detector performance over a wide range of applications, has been undertaken. Prototypes of different sections of the CALIFA Barrel have been modeled and their responses have been evaluated and compared with the experimental results. The present paper summarizes the outcome of the simulation campaign for the entire Barrel section and for the corresponding prototypes tested at different European installations. (C) 2014 Elsevier B.V. All rights reserved
|
|
| 20. |
- Andersen, C. E., et al.
(författare)
-
Medical proton dosimetry using radioluminescence from aluminium oxide crystals attached to optical-fiber cables
- 2007
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576 .- 0167-5087. ; 580:1, s. 466-468
-
Tidskriftsartikel (refereegranskat)abstract
- The prime objective of this study is to investigate if radioluminescence (RL) from carbon-doped aluminum oxide (Al2O3:C) crystals potentially can be used for absorbed dose-rate measurements during proton radiotherapy. The RL from two separate (2 mg) Al2O3:C crystals attached to optical-fiber cables were recorded during irradiations in water in a 175 MeV clinical proton beam. The RL response for low-LET protons in the plateau region of the Bragg curve was found to closely resemble that observed for a clinical 6 MV X-ray beam. An identical response was found in the Bragg peak (where the dose-averaged LET is about 4 keV/mu m) for absorbed doses less than 0.3 Gy. For doses in the range of 0.3-3Gy, we observed a significant decrease in luminescence efficiency with LET. At 3 Gy, the luminescence efficiency was about 60% in the Bragg-peak region. The study implies that the RL-signal from Al2O3:C could potentially be suitable for medical proton dosimetry in the 0-0.3 Gy range even without any LET-dependent correction factors.
|
|
| 21. |
- Andersen, Ken, et al.
(författare)
-
B-10 multi-grid proportional gas counters for large area thermal neutron detectors
- 2013
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002 .- 1872-9576. ; 720, s. 116-121
-
Tidskriftsartikel (refereegranskat)abstract
- He-3 was a popular material in neutrons detectors until its availability dropped drastically in 2008. The development of techniques based on alternative convertors is now of high priority for neutron research institutes. Thin films of B-10 or (B4C)-B-10 have been used in gas proportional counters to detect neutrons, but until now, only for small or medium sensitive area. We present here the multi-grid design, introduced at the ILL and developed in collaboration with ESS for LAN (large area neutron) detectors. Typically thirty (B4C)-B-10 films of 1 mu m thickness are used to convert neutrons into ionizing particles which are subsequently detected in a proportional gas counter. The principle and the fabrication of the multi-grid are described and some preliminary results obtained with a prototype of 200 cm x 8 cm are reported; a detection efficiency of 48% has been measured at 2.5 angstrom with a monochromatic neutron beam line, showing the good potential of this new technique. (C) 2013 Elsevier B.V. All rights reserved.
|
|
| 22. |
- Andersen, K. H., et al.
(författare)
-
The instrument suite of the European Spallation Source
- 2020
-
Ingår i: Nuclear Instruments and Methods in Physics Research, Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 957
-
Tidskriftsartikel (refereegranskat)abstract
- An overview is provided of the 15 neutron beam instruments making up the initial instrument suite of the European Spallation Source (ESS), and being made available to the neutron user community. The ESS neutron source consists of a high-power accelerator and target station, providing a unique long-pulse time structure of slow neutrons. The design considerations behind the time structure, moderator geometry and instrument layout are presented. The 15-instrument suite consists of two small-angle instruments, two reflectometers, an imaging beamline, two single-crystal diffractometers; one for macromolecular crystallography and one for magnetism, two powder diffractometers, and an engineering diffractometer, as well as an array of five inelastic instruments comprising two chopper spectrometers, an inverse-geometry single-crystal excitations spectrometer, an instrument for vibrational spectroscopy and a high-resolution backscattering spectrometer. The conceptual design, performance and scientific drivers of each of these instruments are described. All of the instruments are designed to provide breakthrough new scientific capability, not currently available at existing facilities, building on the inherent strengths of the ESS long-pulse neutron source of high flux, flexible resolution and large bandwidth. Each of them is predicted to provide world-leading performance at an accelerator power of 2 MW. This technical capability translates into a very broad range of scientific capabilities. The composition of the instrument suite has been chosen to maximise the breadth and depth of the scientific impact of the early years of the ESS, and provide a solid base for completion and further expansion of the facility.
|
|
| 23. |
- Andersson, Joel, et al.
(författare)
-
New features of the MAX IV thermionic pre-injector
- 2017
-
Ingår i: Nuclear Instruments and Methods in Physics Research, Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 855, s. 65-80
-
Tidskriftsartikel (refereegranskat)abstract
- The MAX IV facility in Lund, Sweden consists of two storage rings for production of synchrotron radiation. The smaller 1.5 GeV ring is presently under construction, while the larger 3 GeV ring is being commissioned. Both rings will be operating with top-up injections from a full-energy injector. During injection, the electron beam is first delivered to the main injector from a thermionic pre-injector which consists of a thermionic RF gun, a chopper system, and an energy filter. In order to reduce losses of high-energy electrons along the injector and in the rings, the electron beam provided by the thermionic pre-injector should have the correct time structure and energy distribution. In this paper, the design of the MAX IV thermionic pre-injector with all its sub components is presented. The electron beam delivered by the pre-injector and its dependence on parameters such as optics, cathode temperature, and RF power are studied. Measurements are here compared with simulation results obtained by particle tracking and electromagnetic codes. The chopper system is described in detail, and different driving schemes that optimize the injection efficiency for the two storage rings are investigated. During operation, it was discovered that the structure of the beam delivered by the gun is affected by mode beating between the accelerating and a low-order mode. This mode beating is also studied in detail. Finally, initial measurements of the electron beam delivered to the 3 GeV ring during commissioning are presented.
|
|
| 24. |
- Andersson, L-L, et al.
(författare)
-
TASISpec - A Highly Efficient Multi-coincidence Spectrometer for Nuclear Structure Investigations of the Heaviest Nuclei
- 2010
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 622:1, s. 164-170
-
Tidskriftsartikel (refereegranskat)abstract
- TASISpec (TASCA in Small Image mode Spectroscopy) combines composite Ge- and Si-detectors for a new detector setup aimed towards multi-coincidence gamma -ray, X-ray, conversion electron, fission fragment, and a-particle spectroscopy of the heaviest nuclei. It exploits the TASCA separator's unique small image focal mode, i.e. the fact that evaporation residues produced in fusion-evaporation reactions can be focused into an area of less than 3 cm in diameter. This provides the possibility to pack detectors in very close geometry, resulting in an unprecedented detection efficiency of radioactive decays in prompt and delayed coincidence with implanted nuclei. Crown Copyright (C) 2010 Published by Elsevier B.V. All rights reserved.
|
|
| 25. |
- Antonov, A. N., et al.
(författare)
-
The electron-ion scattering experiment ELISe at the International Facility for Antiproton and Ion Research (FAIR)-A conceptual design study
- 2011
-
Ingår i: Nuclear Instruments and Methods in Physics Research, Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. - : Elsevier BV. - 0168-9002 .- 0167-5087. ; 637:1, s. 60-76
-
Tidskriftsartikel (refereegranskat)abstract
- The electron-ion scattering experiment ELISe is part of the installations envisaged at the new experimental storage ring at the International Facility for Antiproton and Ion Research (FAIR) in Darmstadt, Germany. It offers an unique opportunity to use electrons as probe in investigations of the structure of exotic nuclei. The conceptual design and the scientific challenges of ELISe are presented. (C) 2011 Elsevier B.V. All rights reserved.
|
|
