| 1. |
- Adolfsson, Emelie, et al.
(författare)
-
A system for remote dosimetry audit of 3D-CRT, IMRT and VMAT based on lithium formate dosimetry
- 2014
-
Ingår i: Radiotherapy and Oncology. - : Elsevier. - 0167-8140 .- 1879-0887. ; 113:2, s. 279-282
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of this work was to develop and test a remote end-to-end audit system using lithium formate EPR dosimeters. Four clinics were included in a pilot study, absorbed doses determined in the PTV agreed with TPS calculated doses within ±5% for 3D-CRT and ±7% (k=1) for IMRT/VMAT dose plans.
|
|
| 2. |
- Adolfsson, Emelie, et al.
(författare)
-
Investigation of signal fading in lithium formate EPR dosimeters using a new sensitive method
- 2012
-
Ingår i: Physics in Medicine and Biology. - : Institute of Physics (IOP). - 0031-9155 .- 1361-6560. ; 57:8, s. 2209-2217
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of this study was to investigate signal fading in lithium formate electron paramagnetic resonance (EPR) dosimeters used for clinical applications in radiotherapy. A new experimental method for determination of signal fading, designed to resolve small changes in signal from slowly decaying unstable radicals, was used. Possible signal fading in lithium formate due to different storage temperatures was also tested. Air humidity was kept at a constant level of 33% throughout the experiments. The conclusion drawn from the investigations was that the EPR signal from lithium formate is stable during at least 1 month after irradiation and is not sensitive to variations in storage temperature andlt;40 degrees C when kept at a relative air humidity of 33%. This makes lithium formate a suitable dosimeter for transfer dosimetry in clinical audits.
|
|
| 3. |
- Adolfsson, Emelie, 1985-
(författare)
-
Lithium formate EPR dosimetry for accurate measurements of absorbed dose in radiotherapy
- 2014
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Lithium formate has shown to be a material with properties suitable for electron paramagnetic resonance (EPR) dosimetry, among them up to 7 times higher sensitivity compared to alanine, which is a well-established EPR detector material for dose determinations in radiotherapy.The aim of this thesis was to further investigate the properties of lithium formate and develop the dosimetry system towards applications in radiotherapy. The intrinsic efficiency for energies of relevance to brachytherapy and the signal stability were investigated. The dosimetry system was expanded to include a smaller dosimeter model, suitable for measurements in dose gradient regions. An individual sensitivity correction method was applied to the smaller dosimeters to be able to perform dose determinations with the same precision as for the larger ones. EPR dosimetry in general is time consuming and effort was spent to optimize the signal readout procedure regarding measurement time and measurement precision.The system was applied in two clinical applications chosen for their high demands on the dosimetry system: 1) a dosimetry audit for external photon beam therapy and 2) dose verification measurements around a low energy HDR brachytherapy source.The conclusions drawn from this thesis were: dose determinations can be performed with a standard uncertainty of 1.8-2.5% using both the original size dosimeters and the new developed smaller ones. The dosimetry system is robust and useful for applications when high measurement precision and accuracy is prioritized. It is a good candidate for dosimetry audits, both in external beam therapy and brachytherapy.
|
|
| 4. |
- Adolfsson, Emelie, et al.
(författare)
-
Measurement of absorbed dose to water around an electronic brachytherapy source : Comparison of two dosimetry systems: lithium formate EPR dosimeters and radiochromic EBT2 film
- 2015
-
Ingår i: Physics in Medicine and Biology. - : Institute of Physics Publishing (IOPP). - 0031-9155 .- 1361-6560. ; 60:9, s. 3869-3882
-
Tidskriftsartikel (refereegranskat)abstract
- Interest in high dose rate (HDR) electronic brachytherapy operating at 50 kV is increasing. For quality assurance it is important to identify dosimetry systems that can measure the absorbed doses in absolute terms which is difficult in this energy region. In this work a comparison is made between two dosimetry systems, EPR lithium formate dosimeters and radiochromic EBT2 film.Both types of dosimeters were irradiated simultaneously in a PMMA phantom using the Axxent EBS. Absorbed dose to water was determined at distances of 10 mm, 30 mm and 50 mm from the EBS. Results were traceable to different primary standards as regards to absorbed dose to water (EPR) and air kerma (EBT2). Monte Carlo simulations were used in absolute terms as a third estimate of absorbed dose to water.Agreement within the estimated expanded (k = 2) uncertainties (5% (EPR), 7% (EBT2)) was found between the results at 30 mm and 50 mm from the x-ray source. The same result was obtained in 4 repetitions of irradiation, indicating high precision in the measurements with both systems. At all distances, agreement between EPR and Monte Carlo simulations was shown as was also the case for the film measurements at 30mm and 50mm. At 10mm the geometry for the film measurements caused too large uncertainty in measured values depending on the exact position (within sub-mm distances) of the EBS and the 10 mm film results were exculded from comparison.This work has demonstrated good performance of the lithium formate EPR dosimetry system in accordance with earlier experiments at higher photon energies (192Ir HDR brachytherapy). It was also highlighted that there might be issues regarding the energy dependence and intrinsic efficiency of the EBT2 film that need to be considered for measurements using low energy sources.
|
|
| 5. |
- Adolfsson, Emelie, et al.
(författare)
-
Optimisation of an EPR dosimetry system for robust and high precision dosimetry
- 2014
-
Ingår i: Radiation Measurements. - : Elsevier. - 1350-4487 .- 1879-0925. ; 70, s. 21-28
-
Tidskriftsartikel (refereegranskat)abstract
- Clinical applications of electron paramagnetic resonance (EPR) dosimetry systems demand high accuracy causing time consuming analysis. The need for high spatial resolution dose measurements in regions with steep dose gradients demands small sized dosimeters. An optimization of the analysis was therefore needed to limit the time consumption. The aim of this work was to introduce a new smaller lithium formate dosimeter model (diameter reduced from standard diameter 4.5 mm to 3 mm and height from 4.8 mm to 3 mm). To compensate for reduced homogeneity in a batch of the smaller dosimeters, a method for individual sensitivity correction suitable for EPR dosimetry was tested. Sensitivity and repeatability was also tested for a standard EPR resonator and a super high Q (SHQE) one. The aim was also to optimize the performance of the dosimetry system for better efficiency regarding measurement time and precision. A systematic investigation of the relationship between measurement uncertainty and number of readouts per dosimeter was performed. The conclusions drawn from this work were that it is possible to decrease the dosimeter size with maintained measurement precision by using the SHQE resonator and introducing individual calibration factors for dosimeter batches. It was also shown that it is possible reduce the number of readouts per dosimeter without significantly decreasing the accuracy in measurements.
|
|
| 6. |
- Adolfsson, Emelie, 1985-, et al.
(författare)
-
Response of Lithium Formate EPR Dosimeters at Photon Energies Relelvant to Brachytherapy
- 2009
-
Ingår i: IFMBE Proceedings. - Heidelberg : Springer Berlin Heidelberg. - 9783642034725 - 9783642034749 ; , s. 236-239
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- After development of sensitive dosimeter materials Electron Paramagnetic Resonance EPR dosimetry has been successfully used also in radiation therapy. The intensity of the EPR-signal is a measure of the amount of free radicals created by ionizing radiation which is proportional to the absorbed dose in the dosimeter. Lithium formate monohydrate is a dosimeter material with 2-6 times higher sensitivity than alanine, a linear dose response over a wide dose range and mass-energy absorption properties similar to water. These properties make lithium formate promising for verification of absorbed doses around high dose rate brachytherapy sources where the dose gradient is steep and the photon energy distribution changing with distance from the source. Calibration of the dosimeters is performed in 60Co or MV photon beams where high dosimetric accuracy is feasible. The use in brachytherapy field relies on the assumption that the production of free radicals per mean absorbed dose in the dosimeter is similar at the lower photon energies present there. The aim of this work was to test that assumption. The response of the dosimeters as a function of photon energy was determined by irradiations with four x-ray qualities in the range 100-250 kV and 137Cs, relative to the response when irradiated with 60Co, all photon beams with well-known air kerma rates at the Swedish Secondary Standards Dosimetry Laboratory. Monte Carlo simulations were used to convert air kerma free in air to mean absorbed dose to the dosimeter. The measured response relative 60Co as a function of photon energy was below unity for all qualities. The maximum deviation from unity was 2.5% (100 kV, 135 kV) with a relative standard deviation of 1.5% (k = 1).
|
|
| 7. |
- Adolfsson, Emelie, et al.
(författare)
-
Response of lithium formate EPR dosimeters at photon energies relevant to the dosimetry of brachytherapy
- 2010
-
Ingår i: Medical physics (Lancaster). - : American Association of Physicists in Medicine. - 0094-2405. ; 37:9, s. 4946-4959
-
Tidskriftsartikel (refereegranskat)abstract
- PURPOSE:To investigate experimentally the energy dependence of the detector response of lithium formate EPR dosimeters for photon energies below 1 MeV relative to that at 60Co energies. High energy photon beams are used in calibrating dosimeters for use in brachytherapy since the absorbed dose to water can be determined with high accuracy in such beams using calibrated ion chambers and standard dosimetry protocols. In addition to any differences in mass-energy absorption properties between water and detector, variations in radiation yield (detector response) with radiation quality, caused by differences in the density of ionization in the energy imparted (LET), may exist. Knowledge of an eventual deviation in detector response with photon energy is important for attaining high accuracy in measured brachytherapy dose distributions.METHODS:Lithium formate EPR dosimeters were irradiated to known levels of air kerma in 25-250 kV x-ray beams and in 137Cs and 60Co beams at the Swedish Secondary Standards Dosimetry Laboratory. Conversions from air kerma free in air into values of mean absorbed dose to the detectors were made using EGSnrc MC simulations and x-ray energy spectra measured or calculated for the actual beams. The signals from the detectors were measured using EPR spectrometry. Detector response (the EPR signal per mean absorbed dose to the detector) relative to that for 60Co was determined for each beam quality.RESULTS:Significant decreases in the relative response ranging from 5% to 6% were seen for x-ray beams at tube voltages < or = 180 kV. No significant reduction in the relative response was seen for 137Cs and 250 kV x rays.CONCLUSIONS:When calibrated in 60Co or MV photon beams, corrections for the photon energy dependence of detector response are needed to achieve the highest accuracy when using lithium formate EPR dosimeters for measuring absorbed doses around brachytherapy sources emitting photons in the energy range of 20-150 keV such as 169Yb and electronic sources.
|
|
| 8. |
- Antonovic, Laura, et al.
(författare)
-
Evaluation of a lithium formate EPR dosimetry system for dose measurements around Ir-192 brachytherapy sources
- 2009
-
Ingår i: MEDICAL PHYSICS. - : Wiley. - 0094-2405. ; 36:6, s. 2236-2247
-
Tidskriftsartikel (refereegranskat)abstract
- A dosimetry system using lithium formate monohydrate (HCO2Li center dot H2O) as detector material and electron paramagnetic resonance (EPR) spectroscopy for readout has been used to measure absorbed dose distributions around clinical Ir-192 sources. Cylindrical tablets with diameter of 4.5 mm, height of 4.8 mm, and density of 1.26 g/cm(3) were manufactured. Homogeneity test and calibration of the dosimeters were performed in a 6 MV photon beam. Ir-192 irradiations were performed in a PMMA phantom using two different source models, the GammaMed Plus HDR and the microSelectron PDR-v1 model. Measured absorbed doses to water in the PMMA phantom were converted to the corresponding absorbed doses to water in water phantoms of dimensions used by the treatment planning systems (TPSs) using correction factors explicitly derived for this experiment. Experimentally determined absorbed doses agreed with the absorbed doses to water calculated by the TPS to within +/- 2.9%. Relative standard uncertainties in the experimentally determined absorbed doses were estimated to be within the range of 1.7%-1.3% depending on the radial distance from the source, the type of source (HDR or PDR), and the particular absorbed doses used. This work shows that a lithium formate dosimetry system is well suited for measurements of absorbed dose to water around clinical HDR and PDR Ir-192 sources. Being less energy dependent than the commonly used thermoluminescent lithium fluoride (LiF) dosimeters, lithium formate monohydrate dosimeters are well suited to measure absorbed doses in situations where the energy dependence cannot easily be accounted for such as in multiple-source irradiations to verify treatment plans. Their wide dynamic range and linear dose response over the dose interval of 0.2-1000 Gy make them suitable for measurements on sources of the strengths used in clinical applications. The dosimeter size needs, however, to be reduced for application to single-source dosimetry.
|
|
| 9. |
- Carlsson Tedgren, Åsa, 1968-, et al.
(författare)
-
Determination of absorbed dose to water around a clinical HDR 192-Ir source using LiF:Mg,Ti TLDs demonstrates an LET dependence of detector response
- 2012
-
Ingår i: Medical physics (Lancaster). - USA : American Association of Physicists in Medicine. - 0094-2405. ; 39:2, s. 1133-1140
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose: Experimental radiation dosimetry with thermoluminescent dosimeters (TLDs), calibrated in a (60)Co or megavoltage (MV) photon beam, is recommended by AAPM TG-43U1for verification of Monte Carlo calculated absorbed doses around brachytherapy sources. However, it has been shown by Carlsson Tedgren et al. [Med. Phys. 38, 5539-5550 (2011)] that for TLDs of LiF:Mg,Ti, detector response was 4% higher in a (137)Cs beam than in a (60)Co one. The aim of this work was to investigate if similar over-response exists when measuring absorbed dose to water around (192)Ir sources, using LiF:Mg,Ti dosimeters calibrated in a 6 MV photon beam.Methods: LiF dosimeters were calibrated to measure absorbed dose to water in a 6 MV photon beam and used to measure absorbed dose to water at distances of 3, 5, and 7 cm from a clinical high dose rate (HDR) (192)Ir source in a polymethylmethacrylate (PMMA) phantom. Measured values were compared to values of absorbed dose to water calculated using a treatment planning system (TPS) including corrections for the difference in energy absorption properties between calibration quality and the quality in the users' (192)Ir beam and for the use of a PMMA phantom instead of the water phantom underlying dose calculations in the TPS.Results: Measured absorbed doses to water around the (192)Ir source were overestimated by 5% compared to those calculated by the TPS. Corresponding absorbed doses to water measured in a previous work with lithium formate electron paramagnetic resonance (EPR) dosimeters by Antonovic et al. [Med. Phys. 36, 2236-2247 (2009)], using the same irradiation setup and calibration procedure as in this work, were 2% lower than those calculated by the TPS. The results obtained in the measurements in this work and those obtained using the EPR lithium formate dosimeters were, within the expanded (k = 2) uncertainty, in agreement with the values derived by the TPS. The discrepancy between the results using LiF:Mg,Ti TLDs and the EPR lithium formate dosimeters was, however, statistically significant and in agreement with the difference in relative detector responses found for the two detector systems by Carlsson Tedgren et al. [Med. Phys. 38, 5539-5550 (2011)] and by Adolfsson et al. [Med. Phys. 37, 4946-4959 (2010)].Conclusions: When calibrated in (60)Co or MV photon beams, correction for the linear energy transfer (LET) dependence of LiF:Mg,Ti detector response will be needed as to measure absorbed doses to water in a (192)Ir beam with highest accuracy. Such corrections will depend on the manufacturing process (MTS-N Poland or Harshaw TLD-100) and details of the annealing and read-out schemes used.
|
|
| 10. |
|
|
| 11. |
- Carlsson Tedgren, Åsa, et al.
(författare)
-
Influence of phantom material and dimensions on experimental Ir-192 dosimetry
- 2009
-
Ingår i: MEDICAL PHYSICS. - : Wiley. - 0094-2405. ; 36:6, s. 2228-2235
-
Tidskriftsartikel (refereegranskat)abstract
- In treatment planning of brachytherapy, absorbed dose is calculated by superposing predetermined distributions of absorbed dose to water in water for the single source according to the irradiation pattern [i.e., placement of the source(s) or dwelling position(s)]. Single-source reference water data are derived from Monte Carlo (MC) simulations and/or experiments. For reasons of positional accuracy, experimental brachytherapy dosimetry is most often performed in plastic phantoms. This work investigates the water equivalence of phantoms made from polystyrene, PMMA, and solid water for Ir-192 dosimetry. The EGSnrc MC code is used to simulate radial absorbed dose distributions in cylindrical phantoms of dimensions ranging in size from diameter and height of 20 cm to diameter and height of 40 cm. Water equivalence prevails if the absorbed dose to water in the plastic phantom is the same as the absorbed dose to water in a water phantom at equal distances from the source. It is shown that water equivalence at a specified distance from the source depends not only on the size of the plastic phantom but also on the size of the water phantom used for comparison. Compared to equally sized water phantoms, phantoms of polystyrene are less water equivalent than phantoms of PMMA and solid water but compared to larger water phantoms they are the most water equivalent. Although phantom dimension is the most important single factor influencing the dose distributions around Ir-192 sources, the effect of material properties is non-negligible and becomes increasingly important as phantom dimensions increase. The importance of knowing the size of the water phantom whose data underlies treatment planning systems, when using such data as a reference in, e.g., detector evaluation studies, is discussed. To achieve the highest possible accuracy in experimental dosimetry, phantom-specific correction factors should be used.
|
|
| 12. |
- Carlsson Tedgren, Åsa, et al.
(författare)
-
Response of LiF:Mg,Ti thermoluminescent dosimeters at photon energies relevant to the dosimetry of brachytherapy (andlt; 1 MeV)
- 2011
-
Ingår i: Medical physics (Lancaster). - : American Association of Physicists in Medicine. - 0094-2405. ; 38:10, s. 5539-5550
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose: High energy photon beams are used in calibrating dosimeters for use in brachytherapy since absorbed dose to water can be determined accurately and with traceability to primary standards in such beams, using calibrated ion chambers and standard dosimetry protocols. For use in brachytherapy, beam quality correction factors are needed, which include corrections for differences in mass energy absorption properties between water and detector as well as variations in detector response (intrinsic efficiency) with radiation quality, caused by variations in the density of ionization (linear energy transfer (LET) -distributions) along the secondary electron tracks. The aim of this work was to investigate experimentally the detector response of LiF:Mg, Ti thermoluminescent dosimeters (TLD) for photon energies below 1 MeV relative to (60)Co and to address discrepancies between the results found in recent publications of detector response. less thanbrgreater than less thanbrgreater thanMethods: LiF:Mg,Ti dosimeters of formulation MTS-N Poland were irradiated to known values of air kerma free-in-air in x-ray beams at tube voltages 25-250 kV, in (137)Cs- and (60)Co-beams at the Swedish Secondary Standards Dosimetry Laboratory. Conversions from air kerma free-in-air into values of mean absorbed dose in the dosimeters in the actual irradiation geometries were made using EGSnrc Monte Carlo simulations. X-ray energy spectra were measured or calculated for the actual beams. Detector response relative to that for (60)Co was determined at each beam quality. less thanbrgreater than less thanbrgreater thanResults: An increase in relative response was seen for all beam qualities ranging from 8% at tube voltage 25 kV (effective energy 13 keV) to 3%-4% at 250 kV (122 keV effective energy) and (137)Cs with a minimum at 80 keV effective energy (tube voltage 180 kV). The variation with effective energy was similar to that reported by Davis [Radiat. Prot. Dosim. 106, 33-43 (2003)] with our values being systematically lower by 2%-4%. Compared to the results by Nunn [Med. Phys. 35, 1861-1869 (2008)], the relative detector response as a function of effective energy differed in both shape and magnitude. This could be explained by the higher maximum read-out temperature (350 degrees C) used by Nunn [Med. Phys. 35, 1861-1869 (2008)], allowing light emitted from high-temperature peaks with a strong LET dependence to be registered. Use of TLD-100 by Davis [Radiat. Prot. Dosim. 106, 33-43 (2003)] with a stronger super-linear dose response compared to MTS-N was identified as causing the lower relative detector response in this work. less thanbrgreater than less thanbrgreater thanConclusions: Both careful dosimetry and strict protocols for handling the TLDs are required to reach solid experimental data on relative detector response. This work confirms older findings that an over-response relative to (60)Co exists for photon energies below 200-300 keV. Comparison with the results from the literature indicates that using similar protocols for annealing and read-out, dosimeters of different makes (TLD-100, MTS-N) differ in relative detector response. Though universality of the results has not been proven and further investigation is needed, it is anticipated that with the use of strict protocols for annealing and read-out, it will be possible to determine correction factors that can be used to reduce uncertainties in dose measurements around brachytherapy sources at photon energies where primary standards for absorbed dose to water are not available.
|
|
| 13. |
- Carlsson Tedgren, Åsa, et al.
(författare)
-
Specification of absorbed dose to water using model-based dose calculation algorithms for treatment planning in brachytherapy
- 2013
-
Ingår i: Physics in Medicine and Biology. - : Institute of Physics Publishing (IOPP). - 0031-9155 .- 1361-6560. ; 58:8, s. 2561-2579
-
Tidskriftsartikel (refereegranskat)abstract
- Model-based dose calculation algorithms (MBDCAs), recently introduced in treatment planning systems (TPS) for brachytherapy, calculate tissue absorbed doses. In the TPS framework, doses have hereto been reported as dose to water and water may still be preferred as a dose specification medium. Dose to tissue medium D-med then needs to be converted into dose to water in tissue D-w,D- med. Methods to calculate absorbed dose to differently sized water compartments/cavities inside tissue, infinitesimal (used for definition of absorbed dose), small, large or intermediate, are reviewed. Burlin theory is applied to estimate photon energies at which cavity sizes in the range 1 nm-10 mm can be considered small or large. Photon and electron energy spectra are calculated at 1 cm distance from the central axis in cylindrical phantoms of bone, muscle and adipose tissue for 20, 50, 300 keV photons and photons from I-125, Yb-169 and Ir-192 sources; ratios of mass-collision-stopping powers and mass energy absorption coefficients are calculated as applicable to convert D-med into D-w,D- med for small and large cavities. Results show that 1-10 nm sized cavities are small at all investigated photon energies; 100 mu m cavities are large only at photon energies andlt;20 keV. A choice of an appropriate conversion coefficient D-w,D- med/D-med is discussed in terms of the cavity size in relation to the size of important cellular targets. Free radicals from DNA bound water of nanometre dimensions contribute to DNA damage and cell killing and may be the most important water compartment in cells implying use of ratios of mass -collision-stopping powers for converting D-med into D-w,D- med.
|
|
| 14. |
- Holm, Åsa, et al.
(författare)
-
A linear programming model for optimizing HDR brachytherapy dose distributions with respect to mean dose in the DVH-tail
- 2013
-
Ingår i: Medical physics (Lancaster). - : American Association of Physicists in Medicine. - 0094-2405. ; 40:8
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose: Recent research has shown that the optimization model hitherto used in high-dose-rate (HDR) brachytherapy corresponds weakly to the dosimetric indices used to evaluate the quality of a dose distribution. Although alternative models that explicitly include such dosimetric indices have been presented, the inclusion of the dosimetric indices explicitly yields intractable models. The purpose of this paper is to develop a model for optimizing dosimetric indices that is easier to solve than those proposed earlier. less thanbrgreater than less thanbrgreater thanMethods: In this paper, the authors present an alternative approach for optimizing dose distributions for HDR brachytherapy where dosimetric indices are taken into account through surrogates based on the conditional value-at-risk concept. This yields a linear optimization model that is easy to solve, and has the advantage that the constraints are easy to interpret and modify to obtain satisfactory dose distributions. less thanbrgreater than less thanbrgreater thanResults: The authors show by experimental comparisons, carried out retrospectively for a set of prostate cancer patients, that their proposed model corresponds well with constraining dosimetric indices. All modifications of the parameters in the authors model yield the expected result. The dose distributions generated are also comparable to those generated by the standard model with respect to the dosimetric indices that are used for evaluating quality. less thanbrgreater than less thanbrgreater thanConclusions: The authors new model is a viable surrogate to optimizing dosimetric indices and quickly and easily yields high quality dose distributions.
|
|
| 15. |
- Holm, Åsa
(författare)
-
Dose Plan Optimization in HDR Brachytherapy using Penalties : Properties and Extensions
- 2011
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- High dose-rate (HDR) brachytherapy is a specific type of radiotherapy used to treat tumours of for example the cervix, prostate, and breasts. In HDR brachytherapy applicators are implanted into or close to the tumour volume. A radioactive source is moved through these applicators and stops at certain positions, known as dwell points. For each patient an anatomy-based dose plan is created that decides for example where to place the applicators, which dwell points to use, and for how long. The aim when creating a dose plan is to deliver an as high dose as possible to the tumour while simultaneously keeping the dose to the surrounding healthy organs as low as possible.In order to improve the quality of dose plans mathematical optimization methods are today used in clinical practice. Usually one solves a linear penalty model that minimizes a weighted deviation from dose intervals provided by a physician. In this thesis we study certain properties and alterations of this model.One interesting property of the model that we study is the distribution of the basic variables. We show that due to the distribution of these variables only a limited number of dwell positions can be used. Since relatively few dwell positions are used some of the corresponding dwell times have to be long in order for the desired overall dose level to be reached. These long dwell times have been observed in clinical practice and are considered to be a problem.Another property that we study is the correlation between the objective value of the linear penalty model and dose-volume parameters used for evaluation of dose plans. We show that the correlation is weak, which implies that optimizing the linear penalty model does not give a solution to the correct problem.Some alternative models are also considered. One that includes into the optimization the decision of where to place the applicators, when HDR brachytherapy is applied for prostate cancer, and one that reduces the long dwell times by using piecewise linear penalties. The solutions to both models show significant improvements.
|
|
| 16. |
- Holm, Åsa, et al.
(författare)
-
Heuristics for Integrated Optimization of Catheter Positioning and Dwell Time Distribution in Prostate HDR Brachytherapy
- 2016
-
Ingår i: Annals of Operations Research. - : Springer. - 0254-5330 .- 1572-9338. ; 236:2, s. 319-339
-
Tidskriftsartikel (refereegranskat)abstract
- High dose-rate (HDR) brachytherapy is a kind of radiotherapy used to treat, among others, prostate cancer. When applied to prostate cancer a radioactive source is moved through catheters implanted into the prostate. For each patient a treatment plan is constructed that decide for example catheter placement and dwell time distribution, that is where to stop the radioactive source and for how long.Mathematical optimization methods has been used to find quality plans with respect to dwell time distribution, however few optimization approaches regarding catheter placement have been studied. In this article we present an integrated optimization model that optimize catheter placement and dwell time distribution simultaneously. Our results show that integrating the two decisions yields greatly improved plans, from 15% to 94% improvement.Since the presented model is computationally demanding to solve we also present three heuristics: tabu search, variable neighbourhood search and genetic algorithm. Of these variable neighbourhood search is clearly the best, outperforming a state-of-the-art optimization software (CPLEX) and the two other heuristics.
|
|
| 17. |
- Holm, Åsa, et al.
(författare)
-
Impact of Using Linear Optimization Models in Dose Planning for HDR Brachytherapy
- 2012
-
Ingår i: Medical physics (Lancaster). - : American Association of Physicists in Medicine. - 0094-2405. ; 39:2, s. 1021-1028
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose: Dose plans generated with optimization models hitherto used in HDR brachytherapy have shown a tendency to yield longer dwell times than manually optimized plans. Concern has been raised for the corresponding undesired hot spots and various methods to mitigate these have been developed. The hypotheses of this work are a) that one cause for the long dwell times is the use of objective functions comprising simple linear penalties and b) that alternative penalties, being piecewise linear, would lead to reduced length of individual dwell times.Methods: The characteristics of the linear penalties and the piecewise linear penalties are analysed mathematically. Experimental comparisons between the two types of penalties are carried out retrospectively for a set of prostate cancer patients.Results: While most dose-volume parameters do not differ significantly between the two types of penalties significant changes can be seen in the dwell times. On the average, total dwell times were reduced by 4.2%, with a reduction of maximum dwell times by 30%, using the alternative penalties.Conclusion: The use of linear penalties in optimization models for HDR brachytherapy is one cause for undesired longer dwell times appearing in mathematically optimized plans. By introducing alternative penalties significant reduction in dwell times can be achieved for HDR brachytherapy dose plans. Although various constraints as to reduce the long dwell times have been developed our finding is of fundamental interest in showing the shape of the objective function to be one reason for their appearance.
|
|
| 18. |
- Holm, Åsa
(författare)
-
Mathematical Optimization of HDR Brachytherapy
- 2013
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- One out of eight deaths throughout the world is due to cancer. Developing new treatments and improving existing treatments is hence of major importance. In this thesis we have studied how mathematical optimization can be used to improve an existing treatment method: high-dose-rate (HDR) brachytherapy.HDR brachytherapy is a radiation modality used to treat tumours of for example the cervix, prostate, breasts, and skin. In HDR brachytherapy catheters are implanted into or close to the tumour volume. A radioactive source is moved through the catheters, and by adjusting where the catheters are placed, called catheter positioning, and how the source is moved through the catheters, called the dwelling time pattern, the dose distribution can be controlled.By constructing an individualized catheter positioning and dwelling time pattern, called dose plan, based on each patient's anatomy, it is possible to improve the treatment result. Mathematical optimization has during the last decade been used to aid in creating individualized dose plans. The dominating optimization model for this purpose is a linear penalty model. This model only considers the dwelling time pattern within already implanted catheters, and minimizes a weighted deviation from dose intervals prescribed by a physician.In this thesis we show that the distribution of the basic variables in the linear penalty model implies that only dwelling time patterns that have certain characteristics can be optimal. These characteristics cause troublesome inhomogeneities in the plans, and although various measures for mitigating these are already available, it is of fundamental interest to understand their cause.We have also shown that the relationship between the objective function of the linear penalty model and the measures commonly used for evaluating the quality of the dose distribution is weak. This implies that even if the model is solved to optimality there is no guarantee that the generated plan is optimal with respect to clinically relevant objectives, or even near-optimal. We have therefore constructed a new model for optimizing the dwelling time pattern. This model approximates the quality measures by the concept conditional value-at-risk, and we show that the relationship between our new model and the quality measures is strong. Furthermore, the new model generates dwelling time patterns that yield high-quality dose distributions.Combining optimization of the dwelling time pattern with optimization of the catheter positioning yields a problem for which it is rarely possible to find a proven optimal solution within a reasonable time frame. We have therefore developed a variable neighbourhood search heuristic that outperforms a state-of-the-art optimization software (CPLEX). We have also developed a tailored branch-and-bound algorithm that is better at improving the dual bound than a general branch-and-bound algorithm. This is a step towards the development of a method that can find proven optimal solutions to the combined problem within a reasonable time frame.
|
|
| 19. |
- Holm, Åsa, et al.
(författare)
-
On the Correlation Between DVH Parameters and Linear Penalties in Optimization of HDR Prostate Brachytherapy Dose Plans
-
Annan publikation (övrigt vetenskapligt/konstnärligt)abstract
- When optimizing dwell times for HDR brachytherapy it is common to use a model comprising an objective of linear penalties. However whether a planis considered good or not depends on other measures such as DVH-based parameters. We show through experiments that the correlation between the value of the objective function and the values of DVH-based parameters, such as D90, is weak in some cases. It seems that the objective function can only classify solutions into better or worse, however it can not distinguish the best with respect to DVH-based parameters.
|
|
| 20. |
- Holm, Åsa, et al.
(författare)
-
Study of the Relationship Between Dosimetric Indices and Linear Penalties in Dose Distribution Optimization for HDR Prostate Brachytherapy
- 2013
-
Annan publikation (övrigt vetenskapligt/konstnärligt)abstract
- Purpose: Most clinical software for optimizing dwelling time patterns is based on a linear penalty model. The quality of a dose distribution generated by the dwelling time pattern is, however, evaluated through a number of dosimetric indices. The purpose of this article is to investigate the relationship between the linear penalty model and the dosimetric indices.Method and Materials: Data sets from three patients, previously treated for prostate cancer with HDR brachytherapy as a boost to external beam therapy, were used for this study, and for each of them 300 random dwelling time patterns were generated. The relationship between the linear penalty model and the dosimetric indices were studied both by the Pearson’s product moment correlation coefficient between the objective function value of the linear penalty model and the values of the dosimetric indices, and by scatter-grams.Results: For one of the three patients we found a clear connection between the linear penalty model and the values of the dosimetric indices, but not for the other two. For the two patients without a clear connection there where some dosimetric indices that actually improved with deteriorating objective function value.Conclusion: The dwelling time pattern found by using the linear penalty model does not correspond to the optimal dose distribution with respect to dosimetric indices.
|
|
| 21. |
- Kaveckyte, Vaiva, et al.
(författare)
-
Investigation of a synthetic diamond detector response in kilovoltage photon beams
- 2020
-
Ingår i: Medical physics (Lancaster). - : Wiley-Blackwell Publishing Inc.. - 0094-2405 .- 2473-4209. ; 47:3, s. 1268-1279
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose An important characteristic of radiation dosimetry detectors is their energy response which consists of absorbed-dose and intrinsic energy responses. The former can be characterized using Monte Carlo (MC) simulations, whereas the latter (i.e., detector signal per absorbed dose to detector) is extracted from experimental data. Such a characterization is especially relevant when detectors are used in nonrelative measurements at a beam quality that differs from the calibration beam quality. Having in mind the possible application of synthetic diamond detectors (microDiamond PTW 60019, Freiburg, Germany) for nonrelative dosimetry of low-energy brachytherapy (BT) beams, we determined their intrinsic and absorbed-dose energy responses in 25-250 kV beams relative to a Co-60 beam, which is usually the reference beam quality for detector calibration in radiotherapy. Material and Methods Three microDiamond detectors and, for comparison, two silicon diodes (PTW 60017) were calibrated in terms of air-kerma free in air in six x-ray beam qualities (from 25 to 250 kV) and in terms of absorbed dose to water in a Co-60 beam at the national metrology laboratory in Sweden. The PENELOPE/penEasy MC radiation transport code was used to calculate the absorbed-dose energy response of the detectors (modeled based on blueprints) relative to air and water depending on calibration conditions. The MC results were used to extract the relative intrinsic energy response of the detectors from the overall energy response. Measurements using an independent setup with a single ophthalmic BEBIG I25.S16 I-125 BT seed (effective photon energy of 28 keV) were used as a qualitative check of the extracted intrinsic energy response correction factors. Additionally, the impact of the thickness of the active volume as well as the presence of extra-cameral components on the absorbed-dose energy response of a microDiamond detector was studied using MC simulations. Results The relative intrinsic energy response of the microDiamond detectors was higher by a factor of 2 in 25 and 50 kV beams compared to the Co-60 beam. The variation in the relative intrinsic energy response of silicon diodes was within 10% over the investigated photon energy range. The use of relative intrinsic energy response correction factors improved the agreement among the absorbed dose to water values determined using microDiamond detectors and silicon diodes, as well as with the TG-43 formalism-based calculations for the I-125 seed. MC study of microDiamond detector design features provided a possible explanation for inter-detector response variation at low-energy photon beams by differences in the effective thickness of the active volume. Conclusions MicroDiamond detectors had a non-negligible variation in the relative intrinsic energy response (factor of 2) which was comparable to that in the absorbed-dose energy response relative to water at low-energy photon beams. Silicon diodes, in contrast, had an absorbed-dose energy dependence on photon energy that varied by a factor of 6, whereas the intrinsic energy dependence on beam quality was within 10%. It is important to decouple these two responses for a full characterization of detector energy response especially when the user and reference beam qualities differ significantly, and MC alone is not enough.
|
|
| 22. |
- Kaveckyte, Vaiva, et al.
(författare)
-
Suitability of microDiamond detectors for the determination of absorbed dose to water around high-dose-rate Ir-192 brachytherapy sources
- 2018
-
Ingår i: Medical physics (Lancaster). - : WILEY. - 0094-2405 .- 2473-4209. ; 45:1, s. 429-437
-
Tidskriftsartikel (refereegranskat)abstract
- Purpose: Experimental dosimetry of high-dose-rate (HDR) Ir-192 brachytherapy (BT) sources is complicated due to high dose and dose-rate gradients, and softening of photon energy spectrum with depth. A single crystal synthetic diamond detector microDiamond (PTW 60019, Freiburg, Germany) has a small active volume, high sensitivity, direct readout, and nearly water-equivalent active volume. The purpose of this study was to evaluate the suitability of microDiamond detectors for the determination of absorbed dose to water around HDR Ir-192 BT sources. Three microDiamond detectors were used, allowing for the comparison of their properties. Methods: In-phantom measurements were performed using microSelectron and VariSource iX HDR Ir-192 BT treatment units. Their treatment planning systems (TPSs), Oncentra (v. 4.3) and BrachyVision (v. 13.6), respectively, were used to create irradiation plans for a cubic PMMA phantom with the microDiamond positioned at one of three source-to-detector distances (SDDs) (1.5, 2.5, and 5.5 cm) at a time. The source was stepped in increments of 0.5 cm over a total length of 6 cm to yield absorbed dose of 2 Gy at the nominal reference-point of the detector. Detectors were calibrated in Co-60 beam in terms of absorbed dose to water, and Monte Carlo (MC) calculated beam quality correction factors were applied to account for absorbed-dose energy dependence. Phantom correction factors were applied to account for differences in dimensions between the measurement phantom and a water phantom used for absorbed dose calculations made with a TPS. The same measurements were made with all three of the detectors. Additionally, dose-rate dependence and stability of the detectors were evaluated in Co-60 beam. Results: The percentage differences between experimentally determined and TPS-calculated absorbed doses to water were from -1.3% to +2.9%. The values agreed to within experimental uncertainties, which were from 1.9% to 4.3% (k = 2) depending on the detector, SDD and treatment delivery unit. No dose-rate or intrinsic energy dependence corrections were applied. All microDiamonds were comparable in terms of preirradiation dose, stability of the readings and energy response, and showed a good agreement. Conclusions: The results indicate that the microDiamond is potentially suitable for the determination of absorbed dose to water around HDR Ir-192 BT sources and may be used for independent verification of TPSs calculations, as well as for QA measurements of HDR Ir-192 BT treatment delivery units at clinical sites. (C) 2017 American Association of Physicists in Medicine
|
|
| 23. |
- Lindstrom, Jan, et al.
(författare)
-
Experimental assessment of a phosphor model for estimating the relative extrinsic efficiency in radioluminescent detectors
- 2020
-
Ingår i: Physica medica (Testo stampato). - : Elsevier. - 1120-1797 .- 1724-191X. ; 76, s. 117-124
-
Tidskriftsartikel (refereegranskat)abstract
- Optimising phosphor screens in dose detectors or imaging sensor designs is a cumbersome and time- consuming work normally involving specialised measuring equipment and advanced modelling. It is known that crucial optical parameters of the same phosphor may vary within a wide range of values. The aim of this work was to experimentally assess a simple previously published model where the case specific optical parameters (scattering and absorption) are instead represented by a fixed, single parameter, the light extinction factor, xi. The term extrinsic efficiency, N, of a phosphor is also introduced, differing from the common denotation "absolute efficiency", after noting that unknown factors (such as temperature dependence) can have an influence during efficiency estimations and hence difficult to claim absoluteness. N is expressed as the ratio of light energy emitted per unit area at the phosphor surface to incident x-ray energy fluence. By focusing on ratios and relative changes in this study, readily available instruments in a Medical Physics Department (i.e. a photometer) could be used. The varying relative extrinsic efficiency for an extended range of particle sizes (7.5 and 25 mu m) and layer thicknesses (220 to 830 mu m) were calculated in the model from the input parameters: the mean particle size of the phosphor, the layer thickness, the light extinction factor and the calculated energy imparted to the layer. In-house manufactured screens (Gd2O2S:Tb) were used for better control of design parameters. The model provided good qualitative agreement to experiment with quantitative deviations in relative extrinsic efficiency within approximately 2%.
|
|
| 24. |
- Magnusson, Maria, 1961-, et al.
(författare)
-
ACCURACY OF CT NUMBERS OBTAINED BY DIRA AND MONOENERGETIC PLUS ALGORITHMS IN DUAL-ENERGY COMPUTED TOMOGRAPHY
- 2021
-
Ingår i: Radiation Protection Dosimetry. - : Oxford University Press. - 0144-8420 .- 1742-3406. ; 195:3-4, s. 212-217
-
Tidskriftsartikel (refereegranskat)abstract
- Dual-energy computed tomography (CT) can be used in radiotherapy treatment planning for the calculation of absorbed dose distributions. The aim of this work is to evaluate whether there is room for improvement in the accuracy of the Monoenergetic Plus algorithm by Siemens Healthineers. A Siemens SOMATOM Force scanner was used to scan a cylindrical polymethyl methacrylate phantom with four rod-inserts made of different materials. Images were reconstructed using ADMIRE and processed with Monoenergetic Plus. The resulting CT numbers were compared with tabulated values and values simulated by the proof-of-a-concept algorithm DIRA developed by the authors. Both the Monoenergetic Plus and DIRA algorithms performed well; the accuracy of attenuation coefficients was better than about ±1% at the energy of 70 keV. Compared with DIRA, the worse performance of Monoenergetic Plus was caused by its (i) two-material decomposition to iodine and water and (ii) imperfect suppression of the beam hardening artifact in ADMIRE.
|
|
| 25. |
- Magnusson, Maria, et al.
(författare)
-
DIRA-3D-a model-based iterative algorithm for accurate dual-energy dual-source 3D helical CT
- 2019
-
Ingår i: Biomedical Engineering & Physics Express. - : IOP PUBLISHING LTD. - 2057-1976. ; 5:6
-
Tidskriftsartikel (refereegranskat)abstract
- Quantitative dual-energy computed tomography may improve the accuracy of treatment planning in radiation therapy. Of special interest are algorithms that can estimate material composition of the imaged object. One example of such an algorithm is the 2D model-based iterative reconstruction algorithm DIRA. The aim of this work is to extend this algorithm to 3D so that it can be used with cone-beams and helical scanning. In the new algorithm, the parallel FBP method was replaced with the approximate 3D FBP-based PI-method. Its performance was tested using a mathematical phantom consisting of six ellipsoids. The algorithm substantially reduced the beam-hardening artefact and the artefacts caused by approximate reconstruction after six iterations. Compared to Alvarez-Macovskis base material decomposition, DIRA-3D does not require geometrically consistent projections and hence can be used in dual-source CT scanners. Also, it can use several tissue-specific material bases at the same time to represent the imaged object.
|
|
