| 1. |
- Armakavicius, Nerijus, et al.
(författare)
-
Cavity-enhanced optical Hall effect in epitaxial graphene detected at terahertz frequencies
- 2017
-
Ingår i: Applied Surface Science. - : Elsevier. - 0169-4332 .- 1873-5584. ; 421, s. 357-360
-
Tidskriftsartikel (refereegranskat)abstract
- Cavity-enhanced optical Hall effect at terahertz (THz) frequencies is employed to determine the free charge carrier properties in epitaxial graphene (EG) with different number of layers grown by high-temperature sublimation on 4H-SiC(0001). We find that one monolayer (ML) EG possesses p-type conductivity with a free hole concentration in the low 1012 cmￜￜￜ2 range and a free hole mobility parameter as high as 1550 cm2/Vs. We also find that 6 ML EG shows n-type doping behavior with a much lower free electron mobility parameter of 470 cm2/Vs and an order of magnitude higher free electron density in the low 1013 cmￜￜￜ2 range. The observed differences are discussed. The cavity-enhanced THz optical Hall effect is demonstrated to be an excellent tool for contactless access to the type of free charge carriers and their properties in two-dimensional materials such as EG.
|
|
| 2. |
- Armakavicius, Nerijus, et al.
(författare)
-
Properties of two-dimensional electron gas in AlGaN/GaN HEMT structures determined by cavity-enhanced THz optical Hall effect
- 2016
-
Ingår i: Physica Status Solidi C-Current Topics in Solid State Physics, Vol 13 No 5-6. - : Wiley-VCH Verlagsgesellschaft. ; , s. 369-373
-
Konferensbidrag (refereegranskat)abstract
- In this work we employ terahertz (THz) ellipsometry to determine two-dimensional electron gas (2DEG) density, mobility and effective mass in AlGaN/GaN high electron mobility transistor structures grown on 4H-SiC substrates. The effect of the GaN interface exposure to low-flow-rate trimethylaluminum (TMA) on the 2DEG properties is studied. The 2DEG effective mass and sheet density are determined tobe in the range of 0.30-0.32m0 and 4.3-5.5×1012 cm–2, respectively. The 2DEG effective mass parameters are found to be higher than the bulk effective mass of GaN, which is discussed in view of 2DEG confinement. It is shown that exposure to TMA flow improves the 2DEG mobility from 2000 cm2/Vs to values above 2200 cm2/Vs. A record mobility of 2332±61 cm2/Vs is determined for the sample with GaN interface exposed to TMA for 30 s. This improvement in mobility is suggested to be due to AlGaN/GaN interface sharpening causing the reduction of interface roughness scattering of electrons in the 2DEG.
|
|
| 3. |
- Boosalis, Alexander, et al.
(författare)
-
Spectroscopic Mapping Ellipsometry of Graphene Grown on 3C SiC
- 2012
-
Ingår i: MRS Proceedings Volume 1407. - : Springer Science and Business Media LLC. ; , s. aa20-43
-
Konferensbidrag (refereegranskat)abstract
- Spectroscopic mapping ellipsometry measurements in the visible spectrum (1.25 to 5.35 eV) are performed to determine the lateral variations of epitaxial graphene properties as grown on 3C SiC. Data taken in the visible spectrum is sensitive to both the Drude absorption of free charge carriers and the characteristic exciton enhanced van Hove singularity at 5 eV. Subsequent analysis with simple oscillator models allows the determination of physical parameters such as free charge carrier scattering time and local graphene thickness with a lateral resolution of 50 microns.
|
|
| 4. |
- Bouhafs, Chamseddine, et al.
(författare)
-
Decoupling and ordering of multilayer graphene on C-face 3C-SiC(111)
- 2016
-
Ingår i: Applied Physics Letters. - : AMER INST PHYSICS. - 0003-6951 .- 1077-3118. ; 109:20
-
Tidskriftsartikel (refereegranskat)abstract
- We show experimentally that few layer graphene (FLG) grown on the carbon terminated surface (C-face) of 3C-SiC(111) is composed of decoupled graphene sheets. Landau level spectroscopy on FLG graphene is performed using the infrared optical Hall effect. We find that Landau level transitions in the FLG exhibit polarization preserving selection rules and the transition energies obey a square-root dependence on the magnetic field strength. These results show that FLG on C-face 3C-SiC(111) behave effectively as a single layer graphene with linearly dispersing bands (Dirac cones) at the graphene K point. We estimate from the Landau level spectroscopy an upper limit of the Fermi energy of about 60 meV in the FLG, which corresponds to a carrier density below 2.5 x 10(11) cm(-2). Low-energy electron diffraction mu-LEED) reveals the presence of azimuthally rotated graphene domains with a typical size of amp;lt;= 200 nm.mu-LEED mapping suggests that the azimuth rotation occurs between adjacent domains within the same sheet rather than vertically in the stack. Published by AIP Publishing.
|
|
| 5. |
- Bouhafs, Chamseddine, et al.
(författare)
-
Multi-scale investigation of interface properties, stacking order and decoupling of few layer graphene on C-face 4H-SiC
- 2017
-
Ingår i: Carbon. - : PERGAMON-ELSEVIER SCIENCE LTD. - 0008-6223 .- 1873-3891. ; 116, s. 722-732
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, we report a multi-scale investigation using several nano-, micro and macro-scale techniques of few layer graphene (FLG) sample consisting of large monolayer (ML) and bilayer (BL) areas grown on C-face 4H-SiC (000-1) by high-temperature sublimation. Single 1 x 1 diffraction patterns are observed by micro-low-energy electron diffraction for ML, BL and trilayer graphene with no indication of out-of-plane rotational disorder. A SiOx layer is identified between graphene and SiC by X-ray photoelectron emission spectroscopy and reflectance measurements. The chemical composition of the interface layer changes towards SiO2 and its thickness increases with aging in normal ambient conditions. The formation mechanism of the interface layer is discussed. It is shown by torsion resonance conductive atomic force microscopy that the interface layer causes the formation of non-ideal Schottky contact between ML graphene and SiC. This is attributed to the presence of a large density of interface states. Mid-infrared optical Hall effect measurements revealed Landau-level transitions in FLG that have a square-root dependence on magnetic field, which evidences a stack of decoupled graphene sheets. Contrary to previous works on decoupled C-face graphene, our BL and FLG are composed of ordered decoupled graphene layers without out-of-plane rotation. (C) 2017 Elsevier Ltd. All rights reserved.
|
|
| 6. |
- Briley, Chad, et al.
(författare)
-
Effects of annealing and conformal alumina passivation on anisotropy and hysteresis of magneto-optical properties of cobalt slanted columnar thin films
- 2017
-
Ingår i: Applied Surface Science. - : ELSEVIER SCIENCE BV. - 0169-4332 .- 1873-5584. ; 421, s. 320-324
-
Tidskriftsartikel (refereegranskat)abstract
- We present magneto-optical dielectric tensor data of cobalt and cobalt oxide slanted columnar thin films obtained by vector magneto-optical generalized ellipsometry. Room-temperature hysteresis magnetization measurements were performed in longitudinal and polar Kerr geometries on samples prior to and after a heat treatment process with and without a conformal Al2O3 passivation coating. The samples have been characterized by generalized ellipsometry, scanning electron microscopy, and Raman spectroscopy in conjuncture with density functional theory. We observe strongly anisotropic hysteresis behaviors, which depend on the nanocolumn and magnetizing field orientations. We find that deposited cobalt films that have been exposed to heat treatment and subsequent atmospheric oxidation into Co3O4, when not conformally passivated, reveal no measurable magneto-optical properties while cobalt films with passivation coatings retain highly anisotropic magneto-optical properties (C) 2016 Published by Elsevier B.V.
|
|
| 7. |
- Fullager, Daniel B., et al.
(författare)
-
Broadband optical properties of aluminium zinc oxide thin films prepared by spatial atomic layer deposition
- 2018
-
Ingår i: Thin Solid Films. - : ELSEVIER SCIENCE SA. - 0040-6090 .- 1879-2731. ; 653, s. 267-273
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, a broadband ellipsometric investigation of aluminium zinc oxide (AZO) from the infrared to the ultraviolet spectral range is presented. Aluminium zinc oxide samples were fabricated using spatial atomic layer deposition (SALD) having a range of percent aluminium incorporation. The AZO was deposited using a coflow of diethyl zinc (DEZ) and dimethyl aluminium isopropoxide (DMAI), where the amount of aluminium incorporation was controlled by varying the DMAI partial pressure. The broadband permittivity is reported as a function of the aluminium content of these aluminium zinc oxide thin films. A model dielectric function, which includes the contribution of recently predicted broad shallow donor states, is presented and discussed. We find that an increase in the aluminium content of the aluminium zinc oxide thin films results in a monotonically decreasing scattering time while the carrier density increases with diminishing efficiency. To demonstrate the necessity of broadband ellipsometric measurements for the accurate determination of the dielectric function of aluminium zinc oxide, a comparison with the classical Drude model and a semi-empirical extended Drude dispersion model, which are frequently employed in the literature to describe the optical response of aluminium zinc oxide, is given.
|
|
| 8. |
- Fullager, Daniel B., et al.
(författare)
-
Infrared dielectric response of nanoscribe IP-dip and IP-L monomers after polymerization from 250 cm(-1) to 6000 cm(-1)
- 2017
-
Ingår i: Optical Materials Express. - : OPTICAL SOC AMER. - 2159-3930 .- 2159-3930. ; 7:3, s. 888-894
-
Tidskriftsartikel (refereegranskat)abstract
- Direct laser writing via two photon polymerization has enabled previously unavailable degrees of freedom in the additive fabrication of micro-to-meso scale structures. The structures produced by these techniques are ideally suited to create optical devices which operate from the THz regime to the near infrared spectrum into the visible spectral range. Here we report on the infrared dielectric response of two monomers IP-dip and IP-L after polymerization which are frequently employed in commercial two photon lithography tools from nanoscribe over the spectral range of 250 cm(-1) to 6000 cm(-1). A parameterized dielectric function model is presented and discussed. (C) 2017 Optical Society of America
|
|
| 9. |
- Fullager, Daniel B., et al.
(författare)
-
Metalized Poly-methacrylate Off-Axis Parabolic Mirrors for Terahertz Imaging Fabricated by Additive Manufacturing
- 2019
-
Ingår i: Journal of Infrared, Millimeter and Terahertz Waves. - : SPRINGER. - 1866-6892 .- 1866-6906. ; 40:3, s. 269-275
-
Tidskriftsartikel (refereegranskat)abstract
- Terahertz radiation sources are currently one of the most widely used non-ionizing illumination mechanisms for security applications and also find increasing utilization in quality control of commercial products. Presently, a majority of these applications rely on scanning rather than direct imaging and implicitly suffer from temporal latency due to post processing. The monetary and temporal cost associated with procuring commercially manufactured optics that are suitable for imaging leads to fundamental limitations in the ability to rapidly develop application-specific imaging modalities using terahertz sources. Herein, we show a novel method for the rapid prototyping of metallic coated poly-methacrylate parabolic reflectors fabricated by stereolithographic 3D printing. Images comparing the performance of a commercially available off-axis parabolic reflector to our metalized poly-methacrylate prototype, which was designed to be identical to the commercially available mirror, are subsequently presented. The images show that at 530 GHz it is possible to produce a metalized poly-methacrylate off-axis paraboloid whose spatial beam profile is nearly identical to that of a commercially available equivalent.
|
|
| 10. |
- Hofmann, Tino, et al.
(författare)
-
Screening effects in metal sculptured thin films studied with terahertz Mueller matrix ellipsometry
- 2017
-
Ingår i: Applied Surface Science. - : ELSEVIER SCIENCE BV. - 0169-4332 .- 1873-5584. ; 421, s. 513-517
-
Tidskriftsartikel (refereegranskat)abstract
- The anisotropic optical dielectric functions of a metal (cobalt) slanted columnar thin film deposited by electronbeam glancing angle deposition are reported for the terahertz (THz) frequency domain before and after the slanted columnar thin film was passivated by a conformal alumina coating. A simple effective medium dielectric function homogenization approach which describes isolated, electrically conductive columns rendering the thin film biaxial (orthorhombic) is used to model the observed optical responses. Upon passivating the slanted columnar thin film with a 3 nm thick alumina film an increase of both the real and the imaginary part of the dielectric function for all major polarizability directions is found and attributed to screening effects within the spatially coherent metal nanocolumns. (C) 2016 Elsevier B.V. All rights reserved.
|
|
| 11. |
- Klionsky, Daniel J., et al.
(författare)
-
Guidelines for the use and interpretation of assays for monitoring autophagy
- 2012
-
Ingår i: Autophagy. - : Informa UK Limited. - 1554-8635 .- 1554-8627. ; 8:4, s. 445-544
-
Forskningsöversikt (refereegranskat)abstract
- In 2008 we published the first set of guidelines for standardizing research in autophagy. Since then, research on this topic has continued to accelerate, and many new scientists have entered the field. Our knowledge base and relevant new technologies have also been expanding. Accordingly, it is important to update these guidelines for monitoring autophagy in different organisms. Various reviews have described the range of assays that have been used for this purpose. Nevertheless, there continues to be confusion regarding acceptable methods to measure autophagy, especially in multicellular eukaryotes. A key point that needs to be emphasized is that there is a difference between measurements that monitor the numbers or volume of autophagic elements (e.g., autophagosomes or autolysosomes) at any stage of the autophagic process vs. those that measure flux through the autophagy pathway (i.e., the complete process); thus, a block in macroautophagy that results in autophagosome accumulation needs to be differentiated from stimuli that result in increased autophagic activity, defined as increased autophagy induction coupled with increased delivery to, and degradation within, lysosomes (in most higher eukaryotes and some protists such as Dictyostelium) or the vacuole (in plants and fungi). In other words, it is especially important that investigators new to the field understand that the appearance of more autophagosomes does not necessarily equate with more autophagy. In fact, in many cases, autophagosomes accumulate because of a block in trafficking to lysosomes without a concomitant change in autophagosome biogenesis, whereas an increase in autolysosomes may reflect a reduction in degradative activity. Here, we present a set of guidelines for the selection and interpretation of methods for use by investigators who aim to examine macroautophagy and related processes, as well as for reviewers who need to provide realistic and reasonable critiques of papers that are focused on these processes. These guidelines are not meant to be a formulaic set of rules, because the appropriate assays depend in part on the question being asked and the system being used. In addition, we emphasize that no individual assay is guaranteed to be the most appropriate one in every situation, and we strongly recommend the use of multiple assays to monitor autophagy. In these guidelines, we consider these various methods of assessing autophagy and what information can, or cannot, be obtained from them. Finally, by discussing the merits and limits of particular autophagy assays, we hope to encourage technical innovation in the field.
|
|
| 12. |
- Knight, S., et al.
(författare)
-
Cavity-enhanced optical Hall effect in two-dimensional free charge carrier gases detected at terahertz frequencies
- 2015
-
Ingår i: Optics Letters. - : Optical Society of America. - 0146-9592 .- 1539-4794. ; 40:12, s. 2688-2691
-
Tidskriftsartikel (refereegranskat)abstract
- The effect of a tunable, externally coupled Fabry-Perot cavity to resonantly enhance the optical Hall effect signatures at terahertz frequencies produced by a traditional Drude-like two-dimensional electron gas is shown and discussed in this Letter. As a result, the detection of optical Hall effect signatures at conveniently obtainable magnetic fields, for example, by neodymium permanent magnets, is demonstrated. An AlInN/GaN-based high-electron mobility transistor structure grown on a sapphire substrate is used for the experiment. The optical Hall effect signatures and their dispersions, which are governed by the frequency and the reflectance minima and maxima of the externally coupled Fabry-Perot cavity, are presented and discussed. Tuning the externally coupled Fabry-Perot cavity strongly modifies the optical Hall effect signatures, which provides a new degree of freedom for optical Hall effect experiments in addition to frequency, angle of incidence, and magnetic field direction and strength. (C) 2015 Optical Society of America
|
|
| 13. |
- Knight, Sean, et al.
(författare)
-
In-situ terahertz optical Hall effect measurements of ambient effects on free charge carrier properties of epitaxial graphene
- 2017
-
Ingår i: Scientific Reports. - : NATURE PUBLISHING GROUP. - 2045-2322. ; 7
-
Tidskriftsartikel (refereegranskat)abstract
- Unraveling the doping-related charge carrier scattering mechanisms in two-dimensional materials such as graphene is vital for limiting parasitic electrical conductivity losses in future electronic applications. While electric field doping is well understood, assessment of mobility and density as a function of chemical doping remained a challenge thus far. In this work, we investigate the effects of cyclically exposing epitaxial graphene to controlled inert gases and ambient humidity conditions, while measuring the Lorentz force-induced birefringence in graphene at Terahertz frequencies in magnetic fields. This technique, previously identified as the optical analogue of the electrical Hall effect, permits here measurement of charge carrier type, density, and mobility in epitaxial graphene on silicon-face silicon carbide. We observe a distinct, nearly linear relationship between mobility and electron charge density, similar to field-effect induced changes measured in electrical Hall bar devices previously. The observed doping process is completely reversible and independent of the type of inert gas exposure.
|
|
| 14. |
- Knight, Sean, et al.
(författare)
-
Tunable cavity-enhanced terahertz frequency-domain optical Hall effect
- 2020
-
Ingår i: Review of Scientific Instruments. - : AMER INST PHYSICS. - 0034-6748 .- 1089-7623. ; 91:8
-
Tidskriftsartikel (refereegranskat)abstract
- Presented here is the development and demonstration of a tunable cavity-enhanced terahertz (THz) frequency-domain optical Hall effect (OHE) technique. The cavity consists of at least one fixed and one tunable Fabry-Perot resonator. The approach is suitable for the enhancement of the optical signatures produced by the OHE in semi-transparent conductive layer structures with plane parallel interfaces. Tuning one of the cavity parameters, such as the external cavity thickness, permits shifting of the frequencies of the constructive interference and provides substantial enhancement of the optical signatures produced by the OHE. A cavity-tuning optical stage and gas flow cell are used as examples of instruments that exploit tuning an external cavity to enhance polarization changes in a reflected THz beam. Permanent magnets are used to provide the necessary external magnetic field. Conveniently, the highly reflective surface of a permanent magnet can be used to create the tunable external cavity. The signal enhancement allows the extraction of the free charge carrier properties of thin films and can eliminate the need for expensive superconducting magnets. Furthermore, the thickness of the external cavity establishes an additional independent measurement condition, similar to, for example, the magnetic field strength, THz frequency, and angle of incidence. A high electron mobility transistor (HEMT) structure and epitaxial graphene are studied as examples. The tunable cavity-enhancement effect provides a maximum increase of more than one order of magnitude in the change of certain polarization components for both the HEMT structure and epitaxial graphene at particular frequencies and external cavity sizes.
|
|
| 15. |
- Li, Y., et al.
(författare)
-
Broadband near-infrared antireflection coatings fabricated by three-dimensional direct laser writing
- 2018
-
Ingår i: Optics Letters. - : OPTICAL SOC AMER. - 0146-9592 .- 1539-4794. ; 43:2, s. 239-242
-
Tidskriftsartikel (refereegranskat)abstract
- Three-dimensional direct laser writing via two-photon polymerization is used to fabricate anti-reflective structured surfaces (ARSSs) composed of subwavelength conicoid features optimized to operate over a wide bandwidth in the near-infrared range from 3700 cm(-1) to 6600 cm(-1) (2.7-1.52 mu m). Analytic Bruggemann effectivemediumcalculations are used to predict nominal geometric parameters such as the fill factor of the constitutive conicoid features of the anti-reflective structured surfaces (ARSSs) presented here. The performance of the ARSSs was investigated experimentally using infrared reflection and transmission measurements. An enhancement of the transmittance by 1.35%-2.14% over a broadband spectral range from 3700 cm(-1) to 6600 cm(-1) (2.7-1.52 mu m) was achieved. We further report on finite-element-based reflection and transmission data using three-dimensional (3D) model geometries for comparison. A good agreement between experimental results and the finite-element-based numerical analysis is observed once as-fabricated deviations from the nominal conicoid forms are included in the model. 3D direct laser writing is demonstrated here as an efficient method for the fabrication and optimization of ARSSs designed for the infrared spectral range. (c) 2018 Optical Society of America
|
|
| 16. |
- Li, Y., et al.
(författare)
-
High-contrast infrared polymer photonic crystals fabricated by direct laser writing
- 2018
-
Ingår i: Optics Letters. - : OPTICAL SOC AMER. - 0146-9592 .- 1539-4794. ; 43:19, s. 4711-4714
-
Tidskriftsartikel (refereegranskat)abstract
- One-dimensional (1D) photonic crystals (PCs) were fabricated by three-dimensional (3D) direct laser writing using a single polymer to obtain reflectance values approaching that o f a gold reference in the near-infrared (near-IR) spectral range. The PCs are composed of alternating compact and low-density polymer layers that provide the necessary periodic variation of the refractive index. The low-density polymer layers are composed of subwavelength-sized pillars which simultaneously serve as a scaffold while also providing refractive index contrast to the adjacent compact polymer layers. The Bruggemann effective medium theory and stratified-layer optical-model calculated reflectivity profiles were employed to optimize the PCs design to operate at a desired wavelength of 1.55 mu m. After the fabrication, the PCs structure was compared to the nominal geometry using complementary scanning electron microscopy and optical microscopy micrographs identifying a true-to-form fabrication. The performance of the PCs was investigated experimentally using FTIR reflection and transmission measurements. A good agreement between stratified-layer optical-model calculated and measured data is observed. Therefore, we demonstrate the ease of predictive design and fabrication of highly efficient ID PCs for the IR spectral range using 3D direct laser writing of a single polymer. (C) 2018 Optical Society of America
|
|
| 17. |
- Li, Yanzeng, et al.
(författare)
-
Near-infrared transmittance enhancement using fully conformal antireflective structured surfaces on microlenses fabricated by direct laser writing
- 2019
-
Ingår i: Optical Engineering. - : SPIE-SOC PHOTO-OPTICAL INSTRUMENTATION ENGINEERS. - 0091-3286 .- 1560-2303. ; 58:1
-
Tidskriftsartikel (refereegranskat)abstract
- Structured surfaces composed of subwavelength-sized features offer multifunctional properties including antireflective characteristics that are increasingly important for the development of micro-optical components. Here, three-dimensional (3-D) direct laser writing, via two-photon polymerization, is used to fabricate planoconvex spherical microlenses with antireflective structured surfaces. The surfaces are composed of subwavelength-sized conicoid structures, which are arranged fully conformal to the convex surface of the microlenses. The dimensions of the conicoid structures are optimized to effectively reduce Fresnel reflection loss over a wide band in the near-infrared spectral range from 1.4 to 2.2 mu m, with a maximum reduction at 1.55 mu m. Infrared reflection and transmission measurements are used, in combination with 3-D finite element calculations, to investigate the performance of the microlenses. The experimental results reveal that in the spectral range from 1.4 to 2.2 mu m an effective suppression of the Fresnel reflection loss at the convex surface of spherical microlenses can be achieved. The transmittance enhancement is ranging from 1% to 3% for spherical microlenses with antireflective structured surfaces, in comparison to an uncoated reference. (C) 2019 Society of Photo-Optical Instrumentation Engineers (SPIE)
|
|
| 18. |
- Li, Yanzeng, et al.
(författare)
-
Optical dielectric function of Si(2,6-bis(benzimidazol-2 -yl)pyridine)(2) determined by spectroscopic ellipsometry
- 2019
-
Ingår i: Optical Materials Express. - : OPTICAL SOC AMER. - 2159-3930 .- 2159-3930. ; 9:8, s. 3469-3475
-
Tidskriftsartikel (refereegranskat)abstract
- Si(bzimpy)(2), a fluorescent organic complex, has been demonstrated as a potential electron transport and electroluminescent layer for organic electronic devices. Despite the successful synthesis and encouraging electroluminescence at 560 nm, the complex dielectric function of the water-stable complex has not been reported yet. In this letter, we report on the first spectroscopic ellipsometry data obtained from a Si(bzimpy)(2) thin film in the spectral range from 300 nm to 1900 nm (0.65 eV to 4.1 eV). A parameterized model dielectric function composed of a Tauc-Lorentz and Gaussian oscillators is employed to analyze the experimental ellipsometry data. We find a good agreement between the absorption energies observed experimentally here and density functional theory calculations reported earlier.
|
|
| 19. |
- Li, Yanzeng, et al.
(författare)
-
Theoretical Study of Enhanced Plasmonic-Photonic Hybrid Cavity Modes in Reciprocal Plasmonic Metasurfaces
- 2021
-
Ingår i: Plasmonics. - : Springer Nature. - 1557-1955 .- 1557-1963. ; 16:6, s. 2241-2247
-
Tidskriftsartikel (refereegranskat)abstract
- A new configuration for metasurface construction is presented to exhibit potential multi-functionalities including perfect absorption, bio/chem sensing, and enhancement of light-matter interaction. The reciprocal plasmonic metasurfaces discussed here are composed of two plasmonic surfaces of reciprocal geometries separated by a dielectric spacer. Compared to conventional metasurfaces this simple geometry exhibits an enhanced optical performance due to the hybrid plasmonic-photonic cavity. The discussed reciprocal metasurface design further enables effective structural optimization and allows for a simple and scalable fabrication. The physical principle and potential applications of the reciprocal plasmonic metasurfaces are demonstrated using numerical and analytical approaches.
|
|
| 20. |
- Li, Y., et al.
(författare)
-
UV to NIR optical properties of IP-Dip, IP-L, and IP-S after two-photon polymerization determined by spectroscopic ellipsometry
- 2019
-
Ingår i: Optical Materials Express. - : OPTICAL SOC AMER. - 2159-3930 .- 2159-3930. ; 9:11, s. 4318-4328
-
Tidskriftsartikel (refereegranskat)abstract
- The polymers IP-Dip, IP-L, and IP-S are among the most commonly used photo-resists employed for the rapid prototyping of optical components using two-photon polymerization. Despite the widespread use of these polymers, measured data on their optical properties is scarce. Recently, the refractive index n of these polymers has been determined in the visible and nearinfrared spectral range. However, the accurate optical properties including extinction coefficient kappa in the ultraviolet spectral range have not been reported yet. Here we report on accurate, ellipsometric measurements of the complex dielectric functions of two-photon polymerized IP-Dip, IP-L, and IP-S in the spectral range from 210 nm to 1500 nm. Model dielectric functions composed of oscillators with Lorentz, Gaussian, and Tauc-Lorentz broadenings are presented for all investigated polymers. (C) 2019 Optical Society of America under the terms of the OSA Open Access Publishing Agreement
|
|
| 21. |
- Lukasczyk, J., et al.
(författare)
-
Report of the TopoInVis TTK Hackathon : Experiences, Lessons Learned, and Perspectives
- 2021
-
Ingår i: Mathematics and Visualization. - Cham : Springer Nature. ; , s. 359-373, s. 359-373
-
Konferensbidrag (refereegranskat)abstract
- This paper documents the organization, the execution, and the results of the Topology ToolKit (TTK) hackathon that took place at the TopoInVis 2019 conference. The primary goal of the hackathon was to promote TTK in our research community as a unified software development platform for topology-based data analysis algorithms. To this end, participants were first introduced to the structure and capabilities of TTK, and then worked on their own TTK-related projects while being mentored by senior TTK developers. Notable outcomes of the hackathon were first steps towards Python and Docker packages, further integration of TTK in Inviwo, the extension of TTK with new algorithms, and the discovery of current limitations of TTK as well as future development directions.
|
|
| 22. |
- Mock, Alyssa, et al.
(författare)
-
Anisotropy, band-to-band transitions, phonon modes, and oxidation properties of cobalt-oxide core-shell slanted columnar thin films
- 2016
-
Ingår i: Applied Physics Letters. - : AMER INST PHYSICS. - 0003-6951 .- 1077-3118. ; 108:5, s. 051905-
-
Tidskriftsartikel (refereegranskat)abstract
- Highly ordered and spatially coherent cobalt slanted columnar thin films (SCTFs) were deposited by glancing angle deposition onto silicon substrates, and subsequently oxidized by annealing at 475 degrees C. Scanning electron microscopy, Raman scattering, generalized ellipsometry, and density functional theory investigations reveal shape-invariant transformation of the slanted nanocolumns from metallic to transparent metal-oxide core-shell structures with properties characteristic of spinel cobalt oxide. We find passivation of Co-SCTFs yielding Co-Al2O3 core-shell structures produced by conformal deposition of a few nanometers of alumina using atomic layer deposition fully prevents cobalt oxidation in ambient and from annealing up to 475 degrees C. (C) 2016 AIP Publishing LLC.
|
|
| 23. |
- Park, S., et al.
(författare)
-
Terahertz-frequency dielectric anisotropy in three-dimensional polymethacrylates fabricated by stereolithography
- 2020
-
Ingår i: Optics Letters. - : OPTICAL SOC AMER. - 0146-9592 .- 1539-4794. ; 45:7, s. 1982-1985
-
Tidskriftsartikel (refereegranskat)abstract
- The anisotropic optical dielectric functions of slanted. columnar layers fabricated using polymethacrylate based stereolithography are reported for the terahertz-frequency domain using generalized spectroscopic ellipsometry. The slanted columnar layers are composed of spatially coherent columnar structures with a diameter of 100 mu m and a length of 700 mu m that are tilted by 45 degrees with respect to the surface normal of the substrates. A simple biaxial (orthorhombic) layer homogenization approach is used to analyze the terahertz ellipsometric data obtained at three different sample azimuthal orientations. The permittivity along the major polarizability directions varies by almost 25%. Our results demonstrate that stereolithography allows tailoring of the polarizability and anisotropy of the host material, and provides a flexible alternative metamaterials fabrication method for the terahertz spectral range. (C) 2020 Optical Society of America
|
|
| 24. |
- Park, Serang, et al.
(författare)
-
Terahertz optical properties of polymethacrylates after thermal annealing
- 2019
-
Ingår i: Journal of Vacuum Science and Technology B. - : A V S AMER INST PHYSICS. - 2166-2746 .- 2166-2754. ; 37:6
-
Tidskriftsartikel (refereegranskat)abstract
- Polymer-based stereolithographic additive manufacturing has been established for the rapid and low-cost fabrication of terahertz (THz) optical components due to its ability to construct complex 3D geometries with high resolution. For polymer-based or integrated optics, thermal annealing processes are often used to optimize material properties. However, despite the growing interest in THz optics fabricated using stereolithography, the effects of thermal annealing on the THz dielectric properties of polymethacrylates compatible with stereolithography have not yet been studied. In this paper, the authors report on the THz ellipsometric response of thermally annealed polymethacrylates prepared using UV polymerization. The findings indicate that the investigated polymethacrylates maintain a stable optical response in the THz spectral range from 650 to 950 GHz after thermal annealing at temperatures up to 70 degrees C for several hours. Published by the AVS.
|
|
| 25. |
- Park, Serang, et al.
(författare)
-
Terahertz to Mid-infrared Dielectric Properties of Polymethacrylates for Stereolithographic Single Layer Assembly
- 2019
-
Ingår i: Journal of Infrared, Millimeter and Terahertz Waves. - : SPRINGER. - 1866-6892 .- 1866-6906. ; 40:9, s. 971-979
-
Tidskriftsartikel (refereegranskat)abstract
- The fabrication of terahertz (THz) optics with arbitrary shapes via polymethacrylate-based stereolithography is very attractive as it may offer a rapid, low-cost avenue towards optimized THz imaging applications. In order to design such THz optical components appropriately, accurate knowledge of the complex dielectric function of the materials used for stereolithographic fabrication is crucial. In this paper, we report on the complex dielectric functions of several polymethacrylates frequently used for stereolithographic fabrication. Spectroscopic ellipsometry data sets from the THz to mid-infrared spectral range were obtained from isotropically cross-linked polymethacrylate samples. The data sets were analyzed using stratified layer optical model calculations with parameterized model dielectric functions. While the infrared spectral range is dominated by a number of strong absorption features with Gaussian profiles, these materials are found to exhibit only weak absorption in the THz frequency range. In conclusion, we find that thin transmissive THz optics can be efficiently fabricated using polymethacrylate-based stereolithographic fabrication.
|
|
