| 1. |
- Chen, Zhe
(författare)
-
Surface Integrity and Fatigue Performance of Nickel-based Superalloys
- 2017
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Due to global warming, the demand for more efficient gas turbines has increased. A way to achieve this, is by increasing the operating temperature of the gas turbine. Therefore, nickel-based superalloys have been developed to withstand these extreme temperatures and loads, especially in the hot sections. Today, the way of operating land-based gas turbines is changing. Instead of running for long periods of time, the operation is becoming more flexible, with ever-increasing cyclic loads and number of start and stop cycles. To handle the increased stress and cycles, component resistance to fatigue failures need to be improved.Surface integrity is critical to fatigue performance, since fatigue cracks normally initiate at a surface. Machining changes the surface integrity which can result in worse fatigue resistance. The work presented in this Ph.D. thesis was conducted in collaboration with Siemens Industrial Turbomachinery AB in Finspång, Sweden. Surface integrity changes which are induced during machining and their effects on fatigue performance have been studied on the alloy Inconel 718. Inconel 718 is a widely-used nickel-based superalloy for high temperature applications in modern gas turbines.Broaching, milling, and wire electrical discharge machining, related to component manufacturing in turbo machinery industries, were included in this study. Machining induced surface defects provide preferential sites for fatigue crack initiation which influence the fatigue performance of the alloy. If compressive residual stresses are induced during machining, they benefit the fatigue life by retarding fatigue crack initiation away from surface regions. Shot peening was performed on machined Inconel 718, by which high compressive residual stresses are deliberately induced. It results in enhanced fatigue performance.The high temperatures in gas turbines generally deteriorate the surface integrity. Recrystallization often occurs in the highly deformed surface layer. Microstructural degradation, in the form of α-Cr precipitates, have also been frequently observed in the deformed surface and sub-surface microstructure. Oxidation at elevated temperatures degrades the surface integrity and thereby also the fatigue performance. Fatigue cracks are preferably initiated at oxidized surface carbides, if thermal exposure has been made prior to the test. It is even worse when high temperatures relax the beneficial surface compression induced by shot-peening and thereby lowering the fatigue resistance.Machinability of a newly developed nickel-based superalloy, AD 730TM, and the surface integrity induced during turning have also been studied in this thesis project. AD 730TM is a candidate for turbine disc applications with an operating temperature above 650 °C. At such high temperatures, Inconel 718 is no longer stable and its mechanical properties start to degrade.To summarize, the results from this thesis work show the importance of understanding surface integrity effects for fatigue applications, especially in harsh environments. Moreover, the knowledge gained through this work could be used for surface enhancement of turbine components which are subjected to a high risk of fatigue failure. These will contribute to more efficient and flexible power generation by gas turbines.
|
|
| 2. |
- Chen, Zhe, 1987-
(författare)
-
Surface Integrity of Broached Inconel 718 and Influence of Thermal Exposure
- 2014
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Inconel 718 is a nickel-based superalloy that is extensively used as a disc material in gas turbine engines. The service life of gas turbine discs is normally governed by the modes of material degradation and fatigue failure since they work mostly at high temperatures and are subjected to cyclic mechanical loadings. Fatigue failures often start with the initiation of cracks at the surface and the precise details of the failure process significantly depend on the surface conditions. In turbine disc production, one of the last manufacturing steps is to broach root fixings, commonly of fir-tree design, for blade mounting. It has always been a challenge when machining Inconel 718 due to its high strength retention at elevated temperatures, rapid work hardening, as well as low thermal conductivity. This usually leads to rapid tool wear, and consequently shorter tool life, and at the end to the deterioration of the surface integrity of the machined components.The aim of this licentiate thesis is to increase our knowledge about the surface integrity, especially microstructure and residual stresses, of broached Inconel 718 and its stability under thermal exposure. This knowledge can later be used for analyzing the initiation and propagation of fatigue cracks in broached Inconel 718, particularly in the case of high temperature fatigue, thereby giving a better understanding of the failure mechanism of gas turbine discs from a fatigue point of view.A broaching operation has been performed using similar cutting conditions as that used in turbo machinery industries for producing fir-tree root fixings. In addition, service damages were analyzed in a retired dis of Inconel 718. Surface defects, severe plastic deformation and generation of high tensile residual stresses have been found to be the main damages to the surface integrity caused by the broaching operation. The machining induced plastic deformation was found to accelerate the microstructural degradation beneath the broached surface when subjected to thermal exposure. The surface tensile residual stresses can be completely removed after short thermal exposure, the tensile layer in the sub-surface region, however, exhibited a high resistance to stress relief at high temperatures. The damage analysis on the retired disc indicated that presence of the highly deformed layer on the machined surface is negative for preventing the occurrence of fretting fatigue in turbine discs.
|
|
| 3. |
- Gustafsson, David, 1983-
(författare)
-
Constitutive and fatigue crack propagation behaviour of Inconel 718
- 2010
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- In this licentiate thesis the work done in the TURBO POWER project Influence of high temperature hold times on the fatigue life of nickel-based superalloys will be presented. The overall objective of this project is to develop and evaluate tools for designing against fatigue in gas turbine applications, with special focus on the nickel-based superalloy Inconel 718. Firstly, the constitutive behaviour of the material has been been studied, where focus has been placed on trying to describe the mean stress relaxation and initial softening of the material under intermediate temperatures. Secondly, the fatigue crack propagation behaviour under high temperature hold times has been studied. Focus has here been placed on investigating the main fatigue crack propagation phenomena with the aim of setting up a basis for fatigue crack propagation modelling.This thesis is divided into two parts. The first part describes the general framework, including basic constitutive and fatigue crack propagation behaviour as well as a theoretical background for the constitutive modelling of mean stress relaxation. This framework is then used in the second part, which consists of the four included papers.
|
|
| 4. |
- Johansson, Mats J., 1958-
(författare)
-
Gas Exchange in the Normal Lung : Experimental studies on the effects of positive end-expiratory pressure and body position
- 2014
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- BACKGROUND: The principal function of the lung is gas exchange requiring adequate ventilation and perfusion at the level of the alveoli. The efficiency of gas exchange is depending on the distributions of regional ventilation (V) and pulmonary blood flow (Q) and their correlation.AIMS: To validate a high-resolution method to quantify regional V and to investigate the combined effect of positive end-expiratory pressure (PEEP) and body position on distributions of regional V and Q in the normal lung with mechanical ventilation. To assess the matching of V and Q by calculating ventilation-perfusion ratio (V/Q) heterogeneity, determining the spatial distribution of V/Q and to investigate the role of nitric oxide (NO) in regional V/Q matching.METHODS: Anesthetized mechanically ventilated sheep were studied in prone or supine position with different levels of PEEP (0, 10 and 20 cmH2O). Measurements of regional V were done by determining the deposition of a wet aerosol of fluorescent microspheres (FMS) with a median mass aerodynamic diameter of 1.1 μm, and validated against Technegas. Radioactive microspheres, 15 μm in diameter, were used for determining regional Q. Nitric oxide synthase (NOS) was inhibited with Nω-nitro-L-arginine methyl ester (L-NAME) to evaluate the role of NO on regional V/Q matching. The right lung was dried at total lung capacity and diced in approx. 1000 regions tracking the spatial location of each region.RESULTS: The deposition of FMS mirrored regional deposition of Technegas and thus regional ventilation well. In prone, with PEEP, only a small dorsal redistribution of V but not of Q was observed. The vertical Q gradient was abolished with PEEP in prone position in conflict with the classical zonal model. In supine position both V and Q were distributed with a unimodal gradient and PEEP displaced the mode further dorsally. V/Q heterogeneity was greater in supine than in prone position with and without PEEP. Furthermore, PEEP generated regions with high V/Q in supine but not in prone position. Inhibition of NOS did not change the V/Q distribution in prone position.CONCLUSION: There were marked differences in redistribution of regional ventilation and regional pulmonary blood flow between prone and supine position when PEEP was applied. NO was not an active mechanism for V/Q matching in normal sheep lungs.
|
|
| 5. |
- Calmunger, Mattias
(författare)
-
High-Temperature Behaviour of Austenitic Alloys : Influence of Temperature and Strain Rate on Mechanical Properties and Microstructural Development
- 2013
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The global increase in energy consumption and the global warming from greenhouse gas emission creates the need for more environmental friendly energy production processes. Biomass power plants with higher efficiency could generate more energy but also reduce the emission of greenhouse gases, e.g. CO2. Biomass is the largest global contributor to renewable energy and offers no net contribution of CO2 to the atmosphere. One way to increase the efficiency of the power plants is to increase temperature and pressure in the boiler parts of the power plant.The materials used for the future biomass power plants, with higher temperature and pressure, require improved properties, such as higher yield strength, creep strength and high-temperature corrosion resistance. Austenitic stainless steels and nickel-base alloys have shown good mechanical and chemical properties at the operation temperatures of today’s biomass power plants. However, the performance of austenitic stainless steels at the future elevated temperatures is not fully understood.The aim of this licentiate thesis is to increase our knowledge about the mechanical performance of austenitic stainless steels at the demanding conditions of the new generation power plants. This is done by using slow strain rate tensile deformation at elevated temperature and long term hightemperature ageing together with impact toughness testing. Microscopy is used to investigate deformation, damage and fracture behaviours during slow deformation and the long term influence of temperature on toughness in the microstructure of these austenitic alloys. Results show that the main deformation mechanisms are planar dislocation deformations, such as planar slip and slip bands. Intergranular fracture may occur due to precipitation in grain boundaries both in tensile deformed and impact toughness tested alloys. The shape and amount of σ-phase precipitates have been found to strongly influence the fracture behaviour of some of the austenitic stainless steels. In addition, ductility is affected differently by temperature depending on alloy tested and dynamic strain ageing may not always lead to a lower ductility.
|
|
| 6. |
- Calmunger, Mattias, 1986-
(författare)
-
On High-Temperature Behaviours of Heat Resistant Austenitic Alloys
- 2015
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Advanced heat resistant materials are important to achieve the transition to long term sustainable power generation. The global increase in energy consumption and the global warming from greenhouse gas emissions create the need for more sustainable power generation processes. Biomass-fired power plants with higher efficiency could generate more power but also reduce the emission of greenhouse gases, e.g. CO2. Biomass offers no net contribution of CO2 to the atmosphere. To obtain greater efficiency of power plants, one option is to increase the temperature and the pressure in the boiler section of the power plant. This requires improved material properties, such as higher yield strength, creep strength and high-temperature corrosion resistance, as well as structural integrity and safety.Today, some austenitic stainless steels are design to withstand temperatures up to 650 °C in tough environments. Nickel-based alloys are designed to withstand even higher temperatures. Austenitic stainless steels are more cost effective than nickel-based alloys due to a lower amount of expensive alloying elements. However, the performance of austenitic stainless steels at the elevated temperatures of future operation conditions in biomass-red power plants is not yet fully understood.This thesis presents research on the influence of long term high-temperature ageing on mechanical properties, the influence of very slow deformation rates at high-temperature on deformation, damage and fracture, and the influence of high-temperature environment and cyclic operation conditions on the material behaviour. Mechanical and thermal testing have been performed followed by subsequent studies of the microstructure, using scanning electron microscopy, to investigate the material behaviours.Results shows that long term ageing at high temperatures leads to the precipitation of intermetallic phases. These intermetallic phases are brittle at room temperature and become detrimental for the impact toughness of some of the austenitic stainless steels. During slow strain rate tensile deformation at elevated temperature time dependent deformation and recovery mechanisms are pronounced. The creep-fatigue interaction behaviour of an austenitic stainless steel show that dwell time gives shorter life at a lower strain range, but has none or small effect on the life at a higher strain range.Finally, this research results in an increased knowledge of the structural, mechanical and chemical behaviour as well as a deeper understanding of the deformation, damage and fracture mechanisms that occur in heat resistant austenitic alloys at high-temperature environments. It is believed that in the long term, this can contribute to material development achieving the transition to more sustainable power generation in biomass-red power plants.
|
|
| 7. |
- Lundberg, Mattias, 1985-
(författare)
-
Residual stresses, fatigue and deformation in cast iron
- 2018
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The complex geometry of cylinder heads in heavy-duty diesel engines makes grey iron or compact graphite iron a preferred material choice due to its price, castability, thermal conductivity and damping capacity. Today’s strict emission laws have increased the demands on engine performance and engine efficiency. This means that material properties such as fatigue resistance need to be improved. Shot peening is often used to improve the fatigue resistance of components and the benefits of shot peening are associated with the induced compressive surface stresses and surface hardening. How different shot peening parameters can affect fatigue strength of grey and compact graphite iron has been investigated within the project underlying this thesis. To do this, X-ray diffraction (XRD) was utilized for residual stress measurements, scanning electron microscopy (SEM) for microstructural characterizations and mechanical fatigue testing for mechanical quantifications. The ultimate aim of this work has been to increase the fatigue resistance of cast iron by residual stress optimization.XRD measurements and SEM examinations revealed that the shot peening parameters shot size and peening intensity significantly influence residual stresses and surface deformation. Residual stress profiles, similar to the one general considered to improve the fatigue strength in steels, were obtained for both grey and compact graphite iron. Uniaxial push-pull fatigue testing on grey iron with these shot peening parameters reduced the fatigue strength with 15–20 %. The negative effect is likely related to surface damage associated with over peening and relatively high subsurface tensile residual stresses. With very gentle shot peening parameters, the uniaxial fatigue strength were unaltered from the base material but when subjected to bending fatigue an increase in fatigue strength were observed. An alternative way to increase the fatigue strength was to conduct a 30 min annealing heat treatment at 285 XC which increased the fatigue strength by almost 10 % in uniaxial loading. The improvement could be an effect of favourable precipitates forming during the annealing, which could hinder dislocation movement during fatigue.Measuring residual stresses using XRD and the sin2 -method demands accurate X-ray elastic constants (XEC) for meticulous stress analysis. The XEC referred to as 1~2s2 should therefore always be calibrated for the specific material used. The experiments conducted revealed that the XEC value is independent of the testing method used in this work. A small correction from the theoretical value should be applied when the material contains small amounts of residual stresses. The amount of residual stresses has a great impact on the XEC and thus on the stress analysis. Concluding that proper analysis of residual stresses in cast iron is not straight forward.
|
|
| 8. |
- Nordmark, Johanna, 1968-
(författare)
-
Aspects of Induced Hypothermia following Cardiopulmonary Resuscitation : Cerebral and Cardiovascular Effects
- 2009
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Hypothermia treatment with cooling to a body temperature of 32-34°C has been shown to be an effective way of improving neurological outcome and survival in unconscious patients successfully resuscitated after cardiac arrest (CA). The method is used clinically but there are still many questions on the biological mechanisms and on how the treatment is best performed. This thesis focuses on cerebral and haemodynamic effects of hypothermia and rewarming. A porcine model of CA was used. To shorten time to reach target temperature, induction of hypothermia, by means of infusion of 4°C cold fluid, was started already during ongoing cardiopulmonary resuscitation. The temperature was satisfactorily reduced without obvious haemodynamic disturbances. Cerebral effects of hypothermia and rewarming were studied. Microdialysis monitoring showed signs of cerebral energy failure (increased lactate/pyruvate-ratio) and excitotoxicity (increased glutamate) immediately after CA. There was a risk of secondary energy failure that was reduced by hypothermia. Intracranial pressure (ICP) increased gradually after CA irrespectively of if hypothermia was used or not. There were no indications of increasing cerebral disturbances during rewarming. Haemodynamic effects of hypothermia treatment and rewarming were examined in a study of patients successfully resuscitated after CA. Hypothermia was induced by means of cold intravenous infusion. No negative effects on the cardiovascular system were revealed. There were indications of decreased intravascular volume in spite of a positive fluid balance. Cerebral microdialysis and ICP recording were performed in four patients. All patients had signs of energy failure and excitotoxicity following CA. ICP was only exceptionally above 20 mmHg. In contrast to the experimental study indications of increasing ischemia were seen during rewarming. Glycerol had a biphasic pattern, perhaps due to an overspill of metabolites from the general circulation. As most patients become extensively anti-coagulated following CA, intracranial monitoring is not suitable to be used in routine care.
|
|
| 9. |
- Sadrossadat, Mohsen, 1963-
(författare)
-
On the Residual Stresses and Microstructure Formation of Aluminum-Silicon Cast Alloys
- 2011
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Cast aluminum-silicon alloys are being increasingly used in automotive and aerospace industries for critical structure applications because of their excellent castability, low density, acceptable mechanical properties and low cost. Different casting and heat treatment parameters largely affect the microstructure and residual stress of the components, which in turn, has a great impact on their mechanical properties. In cast components, residual stresses are those stresses which may remain in the casting after it has been removed from the mould. The magnitude and distribution of the residual stresses can be critical to performance and should be considered in the design of a component. This work has been devoted to study the microstructure formation, residual stresses, and mechanical properties of aluminum-silicon castings. The effects of casting parameters on the microstructure of the selected alloys were investigated by means of optical and scanning electron microscopes. With the help of EDS, WDS, EBSD, and quantitative analysis techniques, it was found that solidification rate, modification, superheat, casting temperature can significantly affect the nucleation and growth, morphology and chemical composition of different phases. Based on the performed microsegregation analysis, a clear correlation between the concentration of silicon in the primary phase and cooling rate was found. Tensile tests at room and elevated temperatures in addition to microhardness experiments were performed to analyse the behaviour of the alloys under mechanical loads. The results showed that elongation to fracture, modulus of elasticity, and ultimate tensile strength of the tested alloys are temperature dependent. Moreover, the obtained information was used to establish a good model for simulating the behaviour of the cast alloys, as well as the mechanical properties and residual stresses. The type and magnitude of residual stresses were mainly evaluated by strain gauge, sectioning, thermal analysis methods, and was also simulated by finite element analysis using Abaqus software. It was found that casting parameters such as superheat, mould hardness, casting temperature, modification, and the casting geometry, can influence the accumulated residual stress in the component. The thermal treatment experiments also indicated that the base temperature of the cast part before fast cooling, maximum temperature difference within the component, and cooling water flow can influence the residual stress. Extensive simulation work done by Abaqus showed that the results obtained by simulation are in a reasonable relationship with the experimental measurements, considering the linearly elastic/linearly isotropically hardening plastic model.
|
|
| 10. |
- Wärner, Hugo, 1988-
(författare)
-
High Temperature Fatigue Behaviour of Austenitic Stainless Steel : Microstructural Evolution during Dwell-Fatigue and Thermomechanical Fatigue
- 2021
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The global energy consumption is increasing and together with global warming from greenhouse gas emission, a need for more environmentally friendly energy production processes is created. Higher efficiency of biomass power plants can be achieved by increasing temperature and pressure in the boiler section, this would increase the generation of electricity along with the reduction in emission of greenhouse gases e.g. CO2. The generation of power must also be flexible to be able to follow the demands of the energy market and this results in a need for cyclic operating conditions with alternating output and multiple start-ups and shut-downs.Because of the need for flexibility, higher temperature and higher pressure of future biomass power plants, the demands of improved mechanical properties of the materials used for the components are also increased. Properties like creep strength, maintained structural integrity, thermomechanical fatigue resistance and high temperature corrosion resistance are critical for materials used in the next generation biomass power plants. Highly alloyed austenitic stainless steels are known to possess such good high temperature properties and are relatively cheap compared to the nickel-base alloys, which are already used in high temperature cyclic conditions for other applications. The behaviour of austenitic stainless steels subjected to future biomass power plants operating conditions are not yet fully investigated.This thesis presents research that includes investigations of the mechanical and microstructural behaviour during high temperature cyclic conditions of austenitic stainless steels. This is done using thermomechanical fatigue testing, dwell-fatigue testing and impact toughness testing at elevated temperatures. Material service degradation as an effect of microstructural evolution is investigated by ageing of some test specimens before testing. Microscopy is used to investigate the connection between the mechanical behaviour and the microstructural deformation- and damage mechanisms of the austenitic stainless steels after testing.The results show that creep-fatigue interaction damage, creep damage and oxidation assisted cracking are present during high temperature cyclic conditions. In addition, ageing results in a less favourable microstructural configuration which negatively affects the resistance to high temperature damage mechanisms. An example of this is the lowering of impact toughness due to precipitation and coarsening of detrimental phases of some aged austenitic stainless steels. Moreover, TMF testing of aged austenitic stainless steels induce oxidation assisted cracking and an embrittling effect that cause significant cyclic life decrease. The creep-fatigue interaction behaviour during dwell-fatigue testing of two austenitic stainless steels generates various crack propagation characteristics. The higher alloyed material shows interchanging intra- and intergranular propagation with dynamic recrystallization, while the lower alloyed material shows propagation exclusively along the grain boundaries by the assistance of fatigue induced slip bands interaction with grain boundary precipitates.The research of this thesis provides a deeper understanding of the structural integrity, deformation mechanisms, damage mechanisms and fracture mechanisms during high temperature cyclic conditions of austenitic stainless steels. Long term, this is believed to contribute to development of suitable materials used as components of future biomass-fired power plants to achieve sustainable power generation.
|
|
| 11. |
- Yuan, Kang, 1987-
(författare)
-
Oxidation and Corrosion of New MCrAlX Coatings : Modelling and Experiments
- 2014
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- MCrAlY coatings (“M” for Ni and/or Co) are widely used for the protection of superalloy components operated at high temperatures such as in the hot sections of gas turbines. The exposure to high temperature can cause coating degradation due to oxidation or hot corrosion at the coating surface. Microstructures in the coating and the coating life are affected also by the diffusion of alloying elements through the coating-superalloy interface. This PhD project, by applying thermodynamic modelling and experimental tests, investigates the oxidation and hot corrosion behavior of new MCrAlX coatings, in which X, referring to minor elements, is used to highlight the functions of such elements.In order to understand and predict the coating degradation progress during thermal exposure, an oxidation-diffusion model has been established for MCrAlX coating-superalloy systems, which integrates the oxidation of aluminum at coating surface, diffusion of alloying elements, and the diffusion-blocking effect in the materials. The predicted chemical composition profile and microstructure agreed well with experimental results in a CoNiCrAlYSiTa-Inconel 792 system. The model was further applied in several coating-superalloy systems to study the influence of coating composition, superalloy composition and temperature on the evolution of microstructure in the coating and the coating life. The results have demonstrated the potential of the model in designing new durable MCrAlX coatings. In addition to the applications in coating-superalloy systems, the model was also adapted for studying the microstructural development in a superalloy in which internal oxidation and nitridation occurred in an oxidation process.The oxidation behavior of some HVOF MCrAlX coatings was studied by thermal exposure at different temperatures (900, 1000, 1100 °C). Different spinels formed above the alumina scale, depending on the oxidation temperature. The minor alloying elements, Ru and Ir, had no direct influence on the oxidation behavior but may affect the phase stability in the coating.MCrAlX coatings were also tested in 48-hour cycles at 900 °C in different hot corrosion environments containing sulphates and/or SO2. The results showed that the coating performance was dependent on coating quality, concentration of Al and Cr in the coating, and the hot corrosion condition. It was also found that the addition of SO2 in the environment may not necessarily be bad for hot corrosion resistance of some MCrAlY coatings.
|
|
| 12. |
- Zhang, Pimin, 1990-
(författare)
-
Performance of MCrAlX coatings : Oxidation, Hot corrosion and Interdiffusion
- 2019
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- MCrAlY coatings (M=Ni and/or Co) are widely used for the protection of superalloy components against oxidation and hot corrosion in the hot sections of gas turbines. The drive for coating systems to bestow adequate oxidation and corrosion resistance upon the components becomes urgent as an inevitable result of the necessary improvement in engine combustion efficiency and service lifetime. Through the careful design of the composition, MCrAlY coating performance can be optimized to meet the needs under different service conditions and component materials, therefore, “MCrAlX”, with “X” stands for the minor alloying elements, is used to highlight the effect. In the present thesis, the performance of new MCrAlX coatings is investigated with respect to oxidation, hot corrosion and interactions between coating-superalloy substrates.Oxidation of MCrAlX coatings can be generally categorized into initial, steady and close-to-end stages. Coating performance can be affected by various factors at different stages, therefore, experiments were designed by targeting the oxidation stages. Investigation on the initial stage oxidation behavior of MCrAlY coatings with post-deposition surface treatments reveals the different growth mechanisms of alumina scales. Surface treatments significantly reduce the alumina growth rate by suppressing transient alumina development and aiding the early formation of α-Al2O3, which improves the long-term oxidation performance of the coating. Similarly, the modification of minor alloy elements in MCrAlX coatings also serves the purpose. The oxidation behavior of new MCrAlX coatings was investigated at the steady oxidation stage, followed by the microstructure observation, thermodynamic and kinetic simulations. As an alternative reactive element addition of Y, Ce shows a negative effect on the formation of columnar alumina scales of high strain tolerance. In comparison, Fe or Ru addition shows no influence on alumina growth, rather than strengthening the phase stability in the coating and reducing the interdiffusion between coating-substrate through different mechanisms. As the oxidation proceeds to the close-to-end stage, a reliable criterion to estimate the capability of coating to form α-Al2O3 is of great importance to accurately evaluate coating lifetime. A temperature-dependent critical Al-activity criterion was proposed to better predict the formation of a continuous α-Al2O3 scale based on correction of elemental activity using thermodynamic database to replace the empirical Al-concentration based criterion.Severe interdiffusion occurs between coating-substrate during high temperature oxidation, accelerating the degradation of the system. Interdiffusion behavior of diffusion couples of superalloys-MCrAlX coatings were examined. It is highlighted that the recrystallization of superficial layer of the substrate contributes to the secondary reaction zone formation and element interdiffusion controls subsequent zone thickening.Study on Type I hot corrosion behavior of new MCrAlX coatings shows that the addition of Fe has no influence on basic fluxing reactions before severe Al depletion from the coating occurs. Instead, it boosts the “effective” Al supply of coating by shifting the equilibrium concentration of Al in the γ phase to a low Al level. Besides, the pre-mature coating degradation at the coating-substrate interface was due to the fast growth of corrosion products from substrate induced large local volume expansions, resulting in early coating spallation.
|
|
| 13. |
- Johansson, Peter, 1953-
(författare)
-
Understanding psychopathy trough the study of long-term violent offenders
- 2006
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Psychopathy describes a collection of personality traits that logically would facilitate violent, criminal behavior. This dissertation deals with issues that might shed light on how to treat or prevent this socially devastating personality disorder: the conceptualization of the disorder; how psychopathic offenders compare with nonpsychopathic offenders; and whether there are some psychopathic offenders who might be more amenable to treatment than others. The four studies use data from a sample of about 400 violent offenders who were assessed in a national prison unit. The first study dealt with the definition of psychopathy. Using exploratory and confirmatory factor analyses of PCL-R scores, we compared the traditional 17- item, two-factor model with a more recently proposed 13-item, three-factor model. Exploratory factor analysis showed that the 13 items yielded three easily interpretable factors: an interpersonal factor, an affective factor, and a behavioral/lifestyle factor. Confirmatory factor analysis showed that this model had a significantly closer fit to the data than the traditional 17-item, two-factor model. The second and third studies compared psychopathic with nonpsychopathic offenders. In the second study we tested whether psychopathic more than nonpsychopathic offenders had histories of hyperactivityimpulsivity- attention problems (HIA) and conduct problems (CP). We used their retrospective reports of conduct problems before the age of 15 and HIA before the age of 10. The results showed that a combination of childhood HIA and CP was typical for psychopathic but not nonpsychopathic offenders. The third study tested the hypothesis that intelligence is positively correlated with severity of criminal development in psychopathic criminals and negatively correlated in nonpsychopathic criminals. That pattern would provide a way of explaining the discrepancy between Cleckley’s view and later empirical work and open the door to new ideas about prevention and treatment. For non-psychopaths, higher total intelligence scores, particularly verbal intelligence, meant a later start in violent crime. For those diagnosed as psychopaths, however, this association was reversed. The fourth study investigated whether meaningful subtypes of psychopathy could be identified. Model-based cluster analysis of Revised Psychopathy Checklist (PCLR Hare, 2003) and trait anxiety scores in the psychopathic subgroup (n = 124; PCL-R > 29) revealed two clusters, which we labeled primary and secondary. Secondary psychopaths had greater trait anxiety and fewer psychopathic traits than primary psychopaths, but comparable levels of antisocial behavior. They also had more borderline personality features, poorer interpersonal functioning, and more symptoms of major mental disorder than primary psychopaths. Psychopathy is a complex and in some ways mysterious disorder, and little is known about how it develops. Taken together, these studies provide some clues that might ultimately lead to ways of preventing the development of psychopathy. Early HIA problems apparently put children in a risk group. Apparently, high intelligence plays a role in the most problematic cases, and the disorder can develop in the presence of anxiety. Although the idea is not without problems, adult psychopaths who are high on anxiety might be more amenable to treatment than those who are not.
|
|
| 14. |
- Karlsson, Alexander
(författare)
-
Evaluating credal set theory as a belief framework in high-level information fusion for automated decision-making
- 2010
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- High-level information fusion is a research field in which methods for achieving an overall understanding of the current situation in an environment of interest are studied. The ultimate goal of these methods is to provide effective decision-support for human or automated decision-making. One of the main proposed ways of achieving this is to reduce the uncertainty, coupled with the decision, by utilizing multiple sources of information. Handling uncertainty in high-level information fusion is performed through a belief framework, and one of the most commonly used such frameworks is based on Bayesian theory. However, Bayesian theory has often been criticized for utilizing a representation of belief and evidence that does not sufficiently express some types of uncertainty. For this reason, a generalization of Bayesian theory has been proposed, denoted as credal set theory, which allows one to represent belief and evidence imprecisely. In this thesis, we explore whether credal set theory yields measurable advantages, compared to Bayesian theory, when used as a belief framework in high-level information fusion for automated decision-making, i.e., when decisions are made by some pre-determined algorithm. We characterize the Bayesian and credal operators for belief updating and evidence combination and perform three experiments where the Bayesian and credal frameworks are evaluated with respect to automated decision-making. The decision performance of the frameworks are measured by enforcing a single decision, and allowing a set of decisions, based on the frameworks’ belief and evidence structures. We construct anomaly detectors based on the frameworks and evaluate these detectors with respect to maritime surveillance. The main conclusion of the thesis is that although the credal framework uses considerably more expressive structures to represent belief and evidence, compared to the Bayesian framework, the performance of the credal framework can be significantly worse, on average, than that of the Bayesian framework, irrespective of the amount of imprecision.
|
|
| 15. |
- Lundberg, Mattias
(författare)
-
Residual Stresses and Fatigue of Shot Peened Cast Iron
- 2013
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The complex geometry of cylinder head in heavy-duty diesel engine makes grey cast iron or compact graphite iron a perfect material choice due to its castability, thermal conductivity and damping capacity. To increase the efficiency of the engine, the fatigue property of the material needs to be improved. Shot peening is often used to increase the fatigue strength of components. The benefits are associated with the compressive stresses induced and with surface hardening. In this research project, these effects on grey and compact iron have been analyzed for different shot peening parameters using XRD, SEM and fatigue testing methods. The ultimate aim of the project is to increase the fatigue strength of cast irons by optimization of residual stresses.The XRD measurements and SEM examinations revealed that the shot peening parameters including shot size and peening intensity had significant influences on the resulted residual stresses and strain hardening while changing the coverage made little difference. Also differences in the peening results between the two materials were observed, which were ascribed to an effect of the different graphite morphology. Nevertheless, a residual stress profile similar to the one general considered to improve the fatigue strength in steels could be obtained in both grey and compact iron after shot peening.The axial fatigue testing with R=-1 on the grey iron showed that peening using large shot size and high peening intensity (heavy shot peening) resulted in a fatigue strength reduction of 15-20% in comparison with the mechanically polished surface. The negative effects are likely related to surface damage and relatively high tensile residual stresses in subsurface induced by the heavy peening. Grey cast iron has low ductility in tension and therefore tensile residual stresses may promote multiple cracking and crack networking during cyclic loading.Shot peening using much smaller shots and lower intensity (gentle shot peening) which resulted in a much smaller residual stress field gave no significant changes in fatigue strength. However, a short time annealing at 285°C of specimens being gently shot peened increased the fatigue strength roughly by 10%. The improvement could be an effect of precipitates formed due to the heat treatment, which lock the dislocation movement under cyclic loading.
|
|
| 16. |
- Sjölander, Emma, 1981-
(författare)
-
Heat treatment of Al-Si-Cu-Mg casting alloys
- 2011
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Environmental savings can be made by increasing the use of aluminium alloys in the automotive industry as the vehicles can be made lighter. Increasing the knowledge about the heat treatment process is one task in the direction towards this goal. The aim of this work is to investigate and model the heat treatment process for Al-Si casting alloys. Three alloys containing Mg and/or Cu were cast using the gradient solidification technique to achieve three different coarsenesses of the microstructure and a low amount of defects. Solution treatment was studied by measuring the concentration of Mg, Cu and Si in the α-Al matrix using wavelength dispersive spectroscopy (WDS) after various times at a solution treatment temperature. A diffusion based model was developed which estimates the time needed to obtain a high and homogenous concentration of alloying elements for different alloys, temperatures and coarsenesses of the microstructure. It was shown that the yield strength after artificial ageing is weakly dependent on the coarseness of the microstructure when the solution treatment time is adjusted to achieve complete dissolution and homogenisation. The shape and position of ageing curves (yield strength versus ageing time) was investigated empirically in this work and by studying the literature in order to differentiate the mechanisms involved. A diffusion based model for prediction of the yield strength after different ageing times was developed for Al-Si-Mg alloys. The model was validated using data available in the literature. For Al-Si-Cu-Mg alloys further studies regarding the mechanisms involved need to be performed. Changes in the microstructure during a heat treatment process influence the plastic deformation behaviour. The Hollomon equation describes the plastic deformation of alloys containing shearable precipitates well, while the Ludwigson equation is needed when a supersaturated solid solution is present. When non-coherent precipitates are present, none of the equations describe the plastic deformation well. The evolution of the storage rate and recovery rate of dislocations was studied and coupled to the evolution of the microstructure using the Kocks-Mecking strain hardening theory.
|
|
| 17. |
- Yuan, Kang
(författare)
-
Thermal and Mechanical Behaviors of High Temperature Coatings
- 2013
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- With superior oxidation and corrosion resistance, metallic coatings (i.e. diffusion coatings and MCrAlX coatings) are widely used to protect hot components made of superalloys in turbine engines. Two issues are critically important for the coating at high temperatures: thermal property related to oxidation/corrosion behavior and microstructure stability, and mechanical properties (e.g. creep and fatigue). The aim of this project is to develop better understanding of the thermal and mechanical behaviors of metallic coatings on superalloys and to improve the accuracy of prediction of their lifetime by thermodynamic modeling. The present work includes an investigation on the oxidation behavior of MCrAlX coating with a new lifetimeprediction model and a study on the influence of diffusion coatings on creep and fatigue behaviors of the superalloy IN792.Experiments on isothermal and thermal cycling oxidation were designed to investigate the oxidation behavior of a HVOF CoNiCrAlYSi coating on superalloy IN792. It is found that the oxidation behaviors of the coating are related to its thermodynamic property. A diffusion model has been established using the homogenization models in the DICTRA software and taking into consideration of the influence of surface oxidation, coating-substrate interdiffusion and diffusion blocking effect caused by internal voids and oxides. The simulation results show an improved accuracy of lifetime prediction by introducing the diffusion blocking effect.Microstructural evolution during creep process at high temperatures was studied in different diffusion coatings (NiAl and PtAl). It is found that the inward diffusion of aluminum controls the thickening rate of the diffusion coatings. The developed coatings displayed two types of mechanical behavior - being easily plasticized or cracked - dependent on temperature and type of coating, and therefore could be considered as non-load carrying material during creep test. The influence of cracking of PtAl coating on the high-cycle fatigue (HCF) behavior of the IN792 was also investigated. The results show that precracking of the coating prior to the fatigue test has little influence on the fatigue limit of specimens with thin coating (50 μm) but lowers the fatigue limit of specimens with thick coating (70 μm). The through-coating crack has enough mobility to penetrate into the substrate and causes fatigue failure only when the driving force for crack propagation is increased above a critical value due to a higher applied stress or a larger crack length (thicker coating).
|
|
| 18. |
- Zhang, Pimin, 1990-
(författare)
-
Oxidation behaviour of MCrAlX coatings : effect of surface treatment and an Al-activity based life criterion
- 2018
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- MCrAlY coatings (M=Ni and/or Co) have been widely used for the protection of superalloy components against oxidation and hot corrosion in the hot sections of gas turbines. The drive to improve engine combustion efficiency while reducing emissions by increasing the operation temperature brings a big challenge for coating design. As a result, the need for improvement of MCrAlY coatings for better oxidation resistance is essential.Formation of a stable, dense, continuous, and slow-growing α-Al2O3 layer, on the MCrAlY coating surface, is the key to oxidation protection, since the protective α-Al2O3 scale offers superior oxidation resistance due to its lower oxygen-diffusion rate as compared with other oxides. The ability of a MCrAlY coating to form and maintain such a protective scale depends on the coating composition and microstructure, and can be improved through optimization of deposition parameters, modification of coating surface conditions, and so on. Part of this thesis work focuses on studying the effect of post-deposition surface treatments on the oxidation behavior of MCrAlX coatings (X can be yttrium and/or other minor alloying elements). The aim is to gain fundamental understanding of alumina scale evolution during oxidation which is important for achieving improved oxidation resistance of MCrAlX coatings. Oxide scale formed on coatings at initial oxidation stage and the effect of surface treatment were investigated by a multi-approach study combining photo-stimulated luminescence, microstructural observation and weight gain. Results showed that both mechanically polished and shot-peened coatings exhibited superior performance due to rapid formation of α-Al2O3 fully covering the coating and suppressing growth of transient alumina, assisted by the high density of α-Al2O3 nuclei on surface treatment induced defects. The early development of a two-layer alumina scale, consisting of an inward-grown inner α-Al2O3 layer and an outer layer transformed from outward-grown transient alumina, resulted in a higher oxide growth rate of the as-sprayed coating. The positive effect of the surface treatments on retarding oxide scale growth and suppressing formation of spinel was also observed in oxidation test up to 1000 hrs.As the oxidation proceeds to the close-to-end stage, a reliable criterion to estimate the capability of coating to form α-Al2O3 is of great importance to accurately evaluate coating lifetime, which is the aim of the other part of the thesis work. Survey of published results on a number of binary Ni-Al and ternary Ni-Cr-Al, Ni-Al-Si systems shows that the empirical Al-concentration based criterion is inadequate to properly predict the formation of a continuous α-Al2O3 scale. On the other hand, correlating the corresponding Al-activity data, calculated from measured chemical compositions using the Thermo-Calc software, to the experimental oxidation results has revealed a temperature dependent, critical Al-activity value for forming continuous α-Al2O3 scale. To validate the criterion, long-term oxidation tests were performed on five MCrAlX coatings with varying compositions and the implementation of the Al-activity based criterion on these coatings successfully predicted α-Al2O3 formation, showing a good agreement with experiment results.
|
|
| 19. |
- Eriksson, Robert
(författare)
-
High-temperature degradation of plasma sprayed thermal barrier coating systems
- 2011
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Thermal barrier coating systems (TBCs) are used in gas turbines to prevent high-temperature degradation of metallic materials in the combustor and turbine. One of the main concerns regarding TBCs is poor reliability, and accurate life prediction models are necessary in order to fully utilise the beneficial effects of TBCs. This research project aims at developing deeper understanding of the degradation and failure mechanisms acting on TBCs during high temperature exposure, and to use this knowledge to improve life assessments of TBCs. The present work includes a study on the influence of coating interface morphology on the fatigue life of TBCs and a study on the influence of some different heat treatments on the adhesive properties of TBCs.The influence of coating interface morphology on fatigue life has been studied both experimentally and by modelling. Large interface roughness has been found experimentally to increase fatigue life of TBCs. The modelling work do, to some extent, capture this behaviour. It is evident, from the study, that interface morphology has a large impact on fatigue life of TBCs.Three thermal testing methods, that degrade TBCs, have been investigated: isothermal oxidation, furnace cycling and burner rig test. The degraded TBCs have been evaluated by adhesion tests and microscopy. The adhesion of TBCs has been found to depend on heat treatment type and length. Cyclic heat treatments, (furnace cycling and burner rig test), lower the adhesion of TBCs while isothermal oxidation increases adhesion. The fracture surfaces from the adhesion tests reveal that failure strongly depends on the pre-existing defects in the TBC.
|
|
| 20. |
- Eriksson, Robert, 1982-
(författare)
-
Thermal Barrier Coatings : Durability Assessment and Life Prediction
- 2013
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Thermal barrier coating (TBC) systems are coating systems containing a metallic bond coat and a ceramic top coat. TBCs are used in gas turbines for thermal insulation and oxidation resistance. Life prediction of TBCs is important as high-temperature exposure degrades the coatings through mechanisms such as thermal fatigue and the formation and growth of thermally grown oxides (TGOs). This thesis presents research on durability assessment and life prediction of air plasma sprayed TBCs.The adhesion of thermal barrier coatings subjected to isothermal oxidation, thermal cycling fatigue and thermal shock was studied. The adhesion strength and fracture characteristics were found to vary with heat treatment type.The influence of interdiffusion between bond coat and substrate was studied on TBCs deposited on two different substrates. The thermal fatigue life was found to differ between the two TBC systems. While fractography and nanoindentation revealed no differences between the TBC systems, the oxidation kinetics was found to differ for non-alumina oxides.The influence of bond coat/top coat interface roughness on the thermal fatigue life was studied; higher interface roughness promoted longer thermal fatigue life. Different interface geometrieswere tried in finite element crack growth simulations, and procedures for creating accurate interface models were suggested.The influence of water vapour and salt deposits on the oxidation/corrosion of a NiCoCrAlY coating and a TBC were studied. Salt deposits gave thicker TGOs and promoted an Y-rich phase. The effect of salt deposits was also evident for TBC coated specimens.A microstructure-based life model was developed using the Thermo-Calc software. The model included coupled oxidation-diffusion, as well as diffusion blocking due to the formation of internal oxides and pores. The model predicted Al-depletion in acceptable agreement with experimental observations.
|
|
| 21. |
- Johansson, Jakob, 1968-
(författare)
-
Cardiopulmonary Resuscitation : Pharmacological Interventions for Augmentation of Cerebral Blood Flow
- 2004
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Cardiac arrest results in immediate interruption of blood flow. The primary goal of cardiopulmonary resuscitation (CPR) is to re-establish blood flow and hence oxygen delivery to the vital organs. This thesis describes different pharmacological interventions aimed at increasing cerebral blood flow during CPR and after restoration of spontaneous circulation (ROSC).In a porcine model of cardiac arrest, continuous infusion of adrenaline generated higher cortical cerebral blood flow during CPR as compared to bolus administration of adrenaline. While bolus doses resulted in temporary peaks in cerebral blood flow, continuous infusion led to a sustained increase in this flow.Administration of vasopressin resulted in higher cortical cerebral blood flow and a lower cerebral oxygen extraction ratio as compared to continuous infusion of adrenaline during CPR. In addition, vasopressin generated higher coronary perfusion pressure during CPR and increased the likelihood of achieving ROSC.Parameters of coagulation and inflammation were measured after successful resuscitation from cardiac arrest. Immediately after ROSC, thrombin-antithrombin complex, a marker of thrombin generation, was elevated and eicosanoid levels were increased, indicating activation of coagulation and inflammation after ROSC. The thrombin generation was accompanied by a reduction in antithrombin. In addition, there was substantial haemoconcentration in the initial period after ROSC.By administration of antithrombin during CPR, supraphysiological levels of antithrombin were achieved. However, antithrombin administration did not increase cerebral circulation or reduce reperfusion injury, as measured by cortical cerebral blood flow, cerebral oxygen extraction and levels of eicosanoids, after ROSC. In a clinical study, the adrenaline dose interval was found to be longer than recommended in the majority of cases of cardiac arrest. Thus, the adherence to recommended guidelines regarding the adrenaline dose interval seems to be poor.
|
|
| 22. |
- Sjögren, Torsten, 1969-
(författare)
-
Influences of the Graphite Phase on Elastic and Plastic Deformation Behaviour of Cast Irons
- 2007
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The amount and morphology of the graphite phase largely controls the resulting properties of cast iron. For instance, in flake graphite cast irons the mechanical properties are low while the thermal conductivity is high. This is in contrast with spheroidal graphite cast irons where the mechanical properties are high and the thermal conductivity is low. These differences are due to the different graphite morphologies and must be accounted for in the design work and material selection of cast iron components. In this work the influence of the graphite phase on the elastic and plastic deformation behaviour of cast irons has been studied.The material grades studied originate from castings for marine diesel engine piston rings with different chemical analyses. Two groups of pearlitic cast iron materials were studied; one with differences in graphite morphology and one with grey irons that differed in graphite content. For these different material grades the mechanical properties were correlated to microstructural parameters. In addition to standard uniaxial tensile tests, acoustic emission measurements were used for the study of deformation.When studying the modulus of elasticity of the cast iron it was found that the modulus of elasticity of the inherent graphite phase depends on the roundness of the graphite particles and is due to the strong anisotropy of the graphite phase. A linear correlation between nodularity and the modulus of elasticity of the graphite phase was derived. This correlation made it possible to account for the anisotropy of the graphite phase in the model used. By applying the linear function when modelling the effective modulus of elasticity, a high accuracy between experimental and theoretical values was achieved.Another factor affecting the elastic response when subjecting a cast iron component to tensile load was found to be the plastic deformation that actually occurs at very low strains for all of the studied cast iron grades. It was observed that the plastic deformation in the low strain elastic region, quantified by using acoustic emission measurements, increased linearly with decreasing modulus of elasticity. These measurements showed that the amount of plastic deformation in the elastic region was largely controlled by the graphite morphology. It was concluded that as the roundness of the graphite particles increases, the plastic deformation activity in the elastic region decreases.The plastic deformation activity continued linearly into the pronounced plastic region of the tensile tests. A decrease in roundness or increase in graphite fraction resulted in an increase of the amount of plastic deformation and the strain hardening exponent. Adependence between strength coefficient and graphite fraction was observed. Models for the flow curves for pearlitic cast irons were developed and shown to accurately reproduce the observed experimental curves.The surveys performed and conclusions from this thesis will be helpful in the design of new cast iron materials.
|
|
| 23. |
- Wärner, Hugo, 1988-
(författare)
-
High-Temperature Fatigue Behaviour of Austenitic Stainless Steel : Influence of Ageing on Thermomechanical Fatigue and Creep-Fatigue Interaction
- 2018
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The global energy consumption is increasing and together with global warming from greenhouse gas emission, create the need for more environmental friendly energy production processes. Higher efficiency of biomass power plants can be achieved by increasing temperature and pressure in the boiler section and this would increase the generation of electricity along with the reduction in emission of greenhouse gases e.g. CO2. The power generation must also be flexible to be able to follow the demands of the energy market, this results in a need for cyclic operating conditions with alternating output and multiple start-ups and shut-downs.Because of the demands of flexibility, higher temperature and higher pressure in the boiler section of future biomass power plants, the demands on improved mechanical properties of the materials of these components are also increased. Properties like creep strength, thermomechanical fatigue resistance and high temperature corrosion resistance are critical for materials used in the next generation biomass power plants. Austenitic stainless steels are known to possess such good high temperature properties and are relatively cheap compared to the nickel-base alloys, which are already operating at high temperature cyclic conditions in other applications. The behaviour of austenitic stainless steels during these widened operating conditions are not yet fully understood.The aim of this licentiate thesis is to increase the knowledge of the mechanical behaviour at high temperature cyclic conditions for austenitic stainless steels. This is done by the use of thermomechanical fatigue- and creepfatigue testing at elevated temperatures. For safety reasons, the effect of prolonged service degradation is investigated by pre-ageing before mechanical testing. Microscopy is used to investigate the microstructural development and resulting damage behaviour of the austenitic stainless steels after testing. The results show that creep-fatigue interaction damage, creep damage and oxidation assisted cracking are present at high temperature cyclic conditions. In addition, simulated service degradation resulted in a detrimental embrittling effect due to the deterioration by the microstructural evolution.
|
|
| 24. |
- Zamani, Mohammadreza, 1985-
(författare)
-
Al-Si Cast Alloys - Microstructure and Mechanical Properties at Ambient and Elevated Temperature
- 2015
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Aluminium alloys with Si as the major alloying element form a class of material providing the most significant part of all casting manufactured materials. These alloys have a wide range of applications in the automotive and aerospace industries due to an excellent combination of castability and mechanical properties, as well as good corrosion resistance and wear resistivity. Additions of minor alloying elements such as Cu and Mg improve the mechanical properties and make the alloy responsive to heat treatment. The aim of this work is studying the role of size and morphology of microstructural constituents (e.g SDAS, Si-particles and intermetalics) on mechanical properties of Al-Si based casting alloy at room temperatures up to 500 ºC.The cooling rate controls the secondary dendrite arm spacing (SDAS), size and distribution of secondary phases. As SDAS becomes smaller, porosity and second phase constituents are dispersed more finely and evenly. This refinement of the microstructure leads to substantial improvement in tensile properties (e.g. Rm and εF). Addition of about 280 ppm Sr to EN AC- 46000 alloy yields fully modified Si-particles (from coarse plates to fine fibres) regardless of the cooling conditions. Depression in eutectic growth temperature as a result of Sr addition was found to be strongly correlated to the level of modification irrespective of coarseness of microstructure. Modification treatment can improve elongation to failure to a great extent as long as the intermetallic compounds are refined in size.Above 300 ºC, tensile strength, Rp0.2 and Rm, of EN AC-46000 alloys are dramatically degraded while the ductility was increased. The fine microstructure (SDAS 10 μm) has superior Rm and ductility compared to the coarse microstructure (SDAS 25 μm) at all test temperature (from room to 500 ºC). Concentration of solutes (e.g. Cu and Mg) in the dendrites increases at 300 ºC and above where Rp0.2 monotonically decreased. The brittleness of the alloy below 300 ºC was related to accumulation of a high volume fraction damaged particles such as Cu- Fe-bearing phases and Si-particles. The initiation rate of damage in the coarse particles was significantly higher, which enhances the probability of failure and decreasing both Rm and εF compared to the fine microstructure. A physically-based model was adapted, improved and validated in order to predict the flow stress behaviour of EN AC- 46000 cast alloys at room temperature up to 400 ºC for various microstructures. The temperature dependant variables of the model were quite well correlated to the underlying physics of the material
|
|
| 25. |
|
|
