| 1. |
- Liu, Tao, et al.
(författare)
-
16% efficiency all-polymer organic solar cells enabled by a finely tuned morphology via the design of ternary blend
- 2021
-
Ingår i: Joule. - : CELL PRESS. - 2542-4351. ; 5:4, s. 914-930
-
Tidskriftsartikel (refereegranskat)abstract
- A SUMMARY There is an urgent demand for all-polymer organic solar cells (AP-OSCs) to gain higher efficiency. Here, we successfully improve the performance to 16.09% by introducing a small amount of BN-T, a B <- N-type polymer acceptor, into the PM6:PY-IT blend. It has been found that BN-T makes the active layer, based on the PM6:PY-IT:BN-T ternary blend, more crystalline but meanwhile slightly reduces the phase separation, leading to enhancement of both exciton harvesting and charge transport. From a thermodynamic viewpoint, BN-T prefers to reside between PM6 and PY-IT, and the fraction of this fine-tunes the morphology. Besides, a significantly reduced nonradiative energy loss occurs in the ternary blend, along with the coexistence of energy and charge transfer between the two acceptors. The progressive performance facilitated by these improved properties demonstrates that AP-OSCs can possibly comparably efficient with those based on small molecule acceptors, further enhancing the competitiveness of this device type.
|
|
| 2. |
- Bai, Yang, et al.
(författare)
-
Geometry design of tethered small-molecule acceptor enables highly stable and efficient polymer solar cells
- 2023
-
Ingår i: Nature Communications. - : NATURE PORTFOLIO. - 2041-1723. ; 14:1
-
Tidskriftsartikel (refereegranskat)abstract
- With the power conversion efficiency of binary polymer solar cells dramatically improved, the thermal stability of the small-molecule acceptors raised the main concerns on the device operating stability. Here, to address this issue, thiophene-dicarboxylate spacer tethered small-molecule acceptors are designed, and their molecular geometries are further regulated via the thiophene-core isomerism engineering, affording dimeric TDY-alpha with a 2, 5-substitution and TDY-beta with 3, 4-substitution on the core. It shows that TDY-alpha processes a higher glass transition temperature, better crystallinity relative to its individual small-molecule acceptor segment and isomeric counterpart of TDY-beta, and amore stablemorphology with the polymer donor. As a result, the TDY-alpha based device delivers a higher device efficiency of 18.1%, and most important, achieves an extrapolated lifetime of about 35000 hours that retaining 80% of their initial efficiency. Our result suggests that with proper geometry design, the tethered small-molecule acceptors can achieve both high device efficiency and operating stability.
|
|
| 3. |
- Chen, Youchun, et al.
(författare)
-
Insights into the working mechanism of cathode interlayers in polymer solar cells via [(C8H17)(4)N](4)[SiW12O40]
- 2016
-
Ingår i: Journal of Materials Chemistry A. - : ROYAL SOC CHEMISTRY. - 2050-7488 .- 2050-7496. ; 4:48, s. 19189-19196
-
Tidskriftsartikel (refereegranskat)abstract
- A low-cost (amp;lt;$1 per g), high-yield (amp;gt;90%), alcohol soluble surfactant-encapsulated polyoxometalate complex [(C8H17)(4)N](4)[SiW12O40] has been synthesized and utilized as a cathode interlayer (CIL) in polymer solar cells (PSCs). A power conversion efficiency of 10.1% can be obtained for PSCs based on PTB7-Th (poly[[2,6-4,8-di(5-ethylhexylthienyl) benzo[1,2-b;3,3-b]-dithiophene][3-fluoro-2[(2-ethylhexyl) carbonyl] thieno [3,4-b]-thiophenediyl]]):PC71BM ([6,6]-phenyl C71-butyric acidmethyl ester) due to the incorporation of [(C8H17)(4)N](4)[SiW12O40]. Combined measurements of current density-voltage characteristics, transient photocurrent, charge carrier mobility and capacitance-voltage characteristics demonstrate that [(C8H17)(4)N](4)[SiW12O40] can effectively increase the built-in potential, charge carrier density and mobility and accelerate the charge carrier extraction in PSCs. Most importantly, the mechanism of using [(C8H17)(4)N](4)[SiW12O40] as the CIL is further brought to light by X-ray photoemission spectroscopy (XPS) and ultraviolet photoemission spectroscopy (UPS) of the metal/ [(C8H17)(4)N](4)[SiW12O40] interface. The findings suggest that [(C8H17)(4)N](4)[SiW12O40] not only decreased the work function of the metal cathodes but also was n-doped upon contact with the metals, which provide insights into the working mechanism of the CILs simultaneously improving the open circuit voltage, short circuit current and fill factor in the PSCs.
|
|
| 4. |
- Zhang, Ben, et al.
(författare)
-
Rapid solidification for green-solvent-processed large-area organic solar modules with >16% efficiency
- 2024
-
Ingår i: Energy & Environmental Science. - : ROYAL SOC CHEMISTRY. - 1754-5692 .- 1754-5706.
-
Tidskriftsartikel (refereegranskat)abstract
- Enabling green-solvent-processed large-area organic solar cells (OSCs) is of great significance to their industrialization. However, precisely controlling the temperature-dependent fluid mechanics and evaporation behavior of green solvents with high-boiling points is challenging. Controlling these parameters is essential to prevent the non-uniform distribution of active layer components and severe molecule aggregation, which collectively degrade the power conversion efficiency (PCE) of large-scale devices. In this study, we revealed that the temperature gradient distribution across a wet film is the root of the notorious Marangoni effect, which leads to the formation of a severely non-uniform active layer on a large scale. Thus, a rapid solidification strategy was proposed to accelerate the evaporation of toluene, a green solvent, at room temperature. This strategy simultaneously inhibits the Marangoni effect and suppresses molecular aggregation in the wet film, allowing the formation of a nano-scale phase separation active layer with uniform morphology. The resultant toluene-processed 15.64-cm2 large-area OSC module achieves an outstanding PCE of 16.03% (certified: 15.69%), which represents the highest reported PCE of green-solvent-processed OSC modules. Notably, this strategy also exhibits a weak scale dependence on the PCE, and we successfully achieved a state-of-the-art PCE of 14.45% for a 72.00-cm2 OSC module. A rapid solidification strategy was developed for simultaneously avoiding the Marangoni effect and suppressing molecular aggregation. The resultant 15.64 cm2 large-area OSC module exhibited a record power conversion efficiency of 16.03%.
|
|
| 5. |
- Zhao, Fuwen, et al.
(författare)
-
Highly efficient fused ring electron acceptors based on a new undecacyclic core
- 2021
-
Ingår i: Materials Chemistry Frontiers. - : ROYAL SOC CHEMISTRY. - 2052-1537. ; 5:4, s. 2001-2006
-
Tidskriftsartikel (refereegranskat)abstract
- Two FREAs, IUIC-O and IUIC-T, based on an undecacyclic core were developed. IUIC-T having a higher extinction coefficient affords aligned energy levels with PBDB-T, finer nanoscale morphology and more orderly molecular stacking, thus achieving more efficient exciton dissociation and charge transport. Therefore, the PBDB-T:IUIC-T based OSC gains a higher PCE of 13.05%.
|
|
| 6. |
- Chen, Haiyang, et al.
(författare)
-
A guest-assisted molecular-organization approach for >17% efficiency organic solar cells using environmentally friendly solvents
- 2021
-
Ingår i: Nature Energy. - : NATURE PORTFOLIO. - 2058-7546. ; 6:11, s. 1045-1053
-
Tidskriftsartikel (refereegranskat)abstract
- The power conversion efficiencies (PCEs) of laboratory-sized organic solar cells (OSCs), usually processed from low-boiling-point and toxic solvents, have reached high values of over 18%. However, there is usually a notable drop of the PCEs when green solvents are used, limiting practical development of OSCs. Herein, we obtain certificated PCEs over 17% in OSCs processed from a green solvent paraxylene (PX) by a guest-assisted assembly strategy, where a third component (guest) is employed to manipulate the molecular interaction of the binary blend. In addition, the high-boiling-point green solvent PX also enables us to deposit a uniform large-area module (36 cm(2)) with a high efficiency of over 14%. The strong molecular interaction between the host and guest molecules also enhances the operational stability of the devices. Our guest-assisted assembly strategy provides a unique approach to develop large-area and high-efficiency OSCs processed from green solvents, paving the way for industrial development of OSCs. Organic solar cells processed from green solvents are easier to implement in manufacturing yet their efficiency is low. Chen et al. devise a guest molecule to improve the molecular packing, enabling devices with over 17% efficiency.
|
|
| 7. |
- Chen, Haiyang, et al.
(författare)
-
Heterogeneous Nucleating Agent for High-Boiling-Point Nonhalogenated Solvent-Processed Organic Solar Cells and Modules
- 2024
-
Ingår i: Advanced Materials. - : WILEY-V C H VERLAG GMBH. - 0935-9648 .- 1521-4095.
-
Tidskriftsartikel (refereegranskat)abstract
- High-boiling-point nonhalogenated solvents are superior solvents to produce large-area organic solar cells (OSCs) in industry because of their wide processing window and low toxicity; while, these solvents with slow evaporation kinetics will lead excessive aggregation of state-of-the-art small molecule acceptors (e.g. L8-BO), delivering serious efficiency losses. Here, a heterogeneous nucleating agent strategy is developed by grafting oligo (ethylene glycol) side-chains on L8-BO (BTO-BO). The formation energy of the obtained BTO-BO; while, changing from liquid in a solvent to a crystalline phase, is lower than that of L8-BO irrespective of the solvent type. When BTO-BO is added as the third component into the active layer (e.g. PM6:L8-BO), it easily assembles to form numerous seed crystals, which serve as nucleation sites to trigger heterogeneous nucleation and increase nucleation density of L8-BO through strong hydrogen bonding interactions even in high-boiling-point nonhalogenated solvents. Therefore, it can effectively suppress excessive aggregation during growth, achieving ideal phase-separation active layer with small domain sizes and high crystallinity. The resultant toluene-processed OSCs exhibit a record power conversion efficiency (PCE) of 19.42% (certificated 19.12%) with excellent operational stability. The strategy also has superior advantages in large-scale devices, showing a 15.03-cm2 module with a record PCE of 16.35% (certificated 15.97%). The heterogeneous nucleating agent (BTO-BO) is developed to suppress the excessive aggregation of L8-BO in high-boiling-point nonhalogenated solvents processing, achieving the active layer with high crystallinity and nano-scaled phase separation morphology. The resultant OSCs achieve record power conversion efficiencies of 19.42% (0.062-cm2) and 16.35% (15. 03-cm2) with excellent operational stabilities. image
|
|
| 8. |
- Jia, Zhenrong, et al.
(författare)
-
Near-infrared absorbing acceptor with suppressed triplet exciton generation enabling high performance tandem organic solar cells
- 2023
-
Ingår i: Nature Communications. - : NATURE PORTFOLIO. - 2041-1723. ; 14:1
-
Tidskriftsartikel (refereegranskat)abstract
- Reducing the energy loss of sub-cells is critical for high performance tandem organic solar cells, while it is limited by the severe non-radiative voltage loss via the formation of non-emissive triplet excitons. Herein, we develop an ultra-narrow bandgap acceptor BTPSeV-4F through replacement of terminal thiophene by selenophene in the central fused ring of BTPSV-4F, for constructing efficient tandem organic solar cells. The selenophene substitution further decrease the optical bandgap of BTPSV-4F to 1.17 eV and suppress the formation of triplet exciton in the BTPSV-4F-based devices. The organic solar cells with BTPSeV-4F as acceptor demonstrate a higher power conversion efficiency of 14.2% with a record high short-circuit current density of 30.1 mA cm(-2) and low energy loss of 0.55 eV benefitted from the low non-radiative energy loss due to the suppression of triplet exciton formation. We also develop a high-performance medium bandgap acceptor O1-Br for front cells. By integrating the PM6:O1-Br based front cells with the PTB7-Th:BTPSeV-4F based rear cells, the tandem organic solar cell demonstrates a power conversion efficiency of 19%. The results indicate that the suppression of triplet excitons formation in the near-infrared-absorbing acceptor by molecular design is an effective way to improve the photovoltaic performance of the tandem organic solar cells. Reducing energy loss of sub-cells is critical for high performance tandem organic solar cells. Here, the authors design and synthesize an ultra-narrow bandgap acceptor through replacement of terminal thiophene by selenophene in the central fused ring, achieving efficiency of 19% for tandem cells.
|
|
| 9. |
- Li, Danqin, et al.
(författare)
-
n-Doping of photoactive layer in binary organic solar cells realizes over 18.3% efficiency
- 2022
-
Ingår i: Nano Energy. - : ELSEVIER. - 2211-2855 .- 2211-3282. ; 96
-
Tidskriftsartikel (refereegranskat)abstract
- Electronic doping of conjugated semiconductor plays a critical role in the fabrication of high efficiency organic optoelectronic devices. Here, we report an organic solar cell (OSC) by doping n-type DMBI-BDZC into one host binary bulk heterojunction (BHJ) photoactive layer comprised of a polymer donor PM6 and a nonfullerene acceptor Y6. The resulting champion device yields a significantly improved power conversion efficiency from 17.17% to 18.33% with an impressive fill factor of 80.20%. It is found that the electrically doped photoactive layer exhibits enhanced and balanced charge carrier mobilities, more effective exciton dissociation, longer carrier lifetime, and suppressed charge recombination with smaller energy loss. The dopant molecule DMBIBDZC also act as a surface morphology modifier of the photoactive layer with enhanced charge transport. This work demonstrates that manipulation of charge transport via adding a low concentration dopant into photoactive layer is a promising approach for further improvement of BHJ OSC performance.
|
|
| 10. |
- Li, Shangyu, et al.
(författare)
-
Tethered Small-Molecule Acceptors Simultaneously Enhance the Efficiency and Stability of Polymer Solar Cells
- 2023
-
Ingår i: Advanced Materials. - : WILEY-V C H VERLAG GMBH. - 0935-9648 .- 1521-4095. ; 35
-
Tidskriftsartikel (refereegranskat)abstract
- For polymer solar cells (PSCs), the mixture of polymer donors and small-molecule acceptors (SMAs) is fine-tuned to realize a favorable kinetically trapped morphology and thus a commercially viable device efficiency. However, the thermodynamic relaxation of the mixed domains within the blend raises concerns related to the long-term operational stability of the devices, especially in the record-holding Y-series SMAs. Here, a new class of dimeric Y6-based SMAs tethered with differential flexible spacers is reported to regulate their aggregation and relaxation behavior. In their polymer blends with PM6, it is found that they favor an improved structural order relative to that of Y6 counterpart. Most importantly, the tethered SMAs show large glass transition temperatures to suppress the thermodynamic relaxation in mixed domains. For the high-performing dimeric blend, an unprecedented open circuit voltage of 0.87 V is realized with a conversion efficiency of 17.85%, while those of regular Y6-base devices only reach 0.84 V and 16.93%, respectively. Most importantly, the dimer-based device possesses substantially reduced burn-in efficiency loss, retaining more than 80% of the initial efficiency after operating at the maximum power point under continuous illumination for 700 h. The tethering approach provides a new direction to develop PSCs with high efficiency and excellent operating stability.
|
|
| 11. |
- Li, Yongxi, et al.
(författare)
-
A fused-ring based electron acceptor for efficient non-fullerene polymer solar cells with small HOMO offset
- 2016
-
Ingår i: NANO ENERGY. - : ELSEVIER SCIENCE BV. - 2211-2855. ; 27, s. 430-438
-
Tidskriftsartikel (refereegranskat)abstract
- A non-fullerene electron acceptor bearing a novel backbone with fused 10-heterocyclic ring (in-dacenodithiopheno-indacenodiselenophene), denoted by IDTIDSe-IC is developed for fullerene free polymer solar cells. IDTIDSe-IC exhibits a low band gap (E-g=1.52 eV) and strong absorption in the 600850 nm region. Combining with a large band gap polymer J51 (E-g=1.91 eV) as donor, broad absorption coverage from 300 nm to 800 nm is obtained due to complementary absorption of J51 and IDTIDSe-IC, which enables a high PCE of 8.02% with a V-oc of 0.91 V, a J(SC) of 15.16 mA/cm(2) and a FF of 58.0% in the corresponding PSCs. Moreover, the EQE of 50-65% is achieved in the absorption range of IDTIDSe-IC with only about 0.1 eV HOMO difference between J51 and IDTIDSe-IC. (C) 2016 Elsevier Ltd. All rights reserved.
|
|
| 12. |
- Li, Yongxi, et al.
(författare)
-
Non-fullerene acceptor with low energy loss and high external quantum efficiency: towards high performance polymer solar cells
- 2016
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry. - 2050-7488 .- 2050-7496. ; 4:16, s. 5890-5897
-
Tidskriftsartikel (refereegranskat)abstract
- A non-fullerene electron acceptor bearing a fused 10-heterocyclic ring (indacenodithiophenoindacenodithiophene) with a narrow band gap (similar to 1.5 eV) was designed and synthesized. It possesses excellent planarity and enhanced effective conjugation length compared to previously reported fused-ring electron acceptors. When this acceptor was paired with PTB7-Th and applied in polymer solar cells, a power conversion efficiency of 6.5% was achieved with a high open circuit voltage of 0.94 V. More significantly, an energy loss as low as 0.59 eV and an external quantum efficiency as high as 63% were obtained simultaneously.
|
|
| 13. |
- Lin, Yuze, et al.
(författare)
-
Mapping Polymer Donors toward High-Efficiency Fullerene Free Organic Solar Cells
- 2017
-
Ingår i: Advanced Materials. - : WILEY-V C H VERLAG GMBH. - 0935-9648 .- 1521-4095. ; 29:3
-
Tidskriftsartikel (refereegranskat)abstract
- Five polymer donors with distinct chemical structures and different electronic properties are surveyed in a planar and narrow-bandgap fused-ring electron acceptor (IDIC)-based organic solar cells, which exhibit power conversion efficiencies of up to 11%.
|
|
| 14. |
- Su, Wenyan, et al.
(författare)
-
13.4 % Efficiency from All-Small-Molecule Organic Solar Cells Based on a Crystalline Donor with Chlorine and Trialkylsilyl Substitutions
- 2021
-
Ingår i: ChemSusChem. - : Wiley. - 1864-5631 .- 1864-564X. ; 14:17, s. 3535-3543
-
Tidskriftsartikel (refereegranskat)abstract
- How to simultaneously achieve both high open-circuit voltage (Voc) and high short-circuit current density (Jsc) is a big challenge for realising high power conversion efficiency (PCE) in all-small-molecule organic solar cells (all-SM OSCs). Herein, a novel small molecule (SM)-donor, namely FYSM−SiCl, with trialkylsilyl and chlorine substitutions was designed and synthesized. Compared to the original SM-donor FYSM−H, FYSM−Si with trialkylsilyl substitution showed a decreased crystallinity and lower highest occupied molecular orbital (HOMO) level, while FYSM−SiCl had an improved crystallinity, more ordered packing arrangement, significantly lower HOMO level, and predominant “face-on” orientation. Matched with a SM-acceptor Y6, the FYSM−SiCl-based all-SM OSCs exhibited both high Voc of 0.85 V and high Jsc of 23.7 mA cm−2, which is rare for all-SM OSCs and could be attributed to the low HOMO level of FYSM−SiCl donor and the delicate balance between high crystallinity and suitable blend morphology. As a result, FYSM−SiCl achieved a high PCE of 13.4 % in all-SM OSCs, which was much higher than those of the FYSM−H- (10.9 %) and FYSM−Si-based devices (12.2 %). This work demonstrated a promising method for the design of efficient SM-donors by a side-chain engineering strategy via the introduction of trialkylsilyl and chlorine substitutions.
|
|
| 15. |
- Yang, Heyi, et al.
(författare)
-
Composition-Conditioning Agent for Doped Spiro-OMeTAD to Realize Highly Efficient and Stable Perovskite Solar Cells
- 2022
-
Ingår i: Advanced Energy Materials. - : WILEY-V C H VERLAG GMBH. - 1614-6832 .- 1614-6840. ; 12:44
-
Tidskriftsartikel (refereegranskat)abstract
- The doped Spiro-OMeTAD hole transport layer (HTL) formed using the lithium bis(trifluoromethane) sulfonimide salt and 4-tert-butylpyridine with phenethylammonium iodide surface treatment on a perovskite film has continuously dominated the record power conversion efficiencies (PCEs) of perovskite solar cells (pero-SCs). However, unstable HTL compositions and iodide salts can cause severe device degradation. In this study, an HTL composition-conditioning agent (CCA), Spiro-BD-2OEG, is designed, which contains a Spiro-OMeTAD-like backbone, functional pyridine units, and oligo (ethylene glycol) chains. This finely designed CCA presents good miscibility with Spiro-OMeTAD and its dopants and acts as a conditioning agent through weak bond interactions. As a result, the CCA-regulated HTL shows a pinhole-free and smooth morphology with enhanced Spiro-OMeTAD ordering and improves dopant stability. In addition, the gradient-distributed CCA in the HTL can narrow the energy level offset with the valence band of the perovskite. The resultant pero-SCs exhibit an excellent PCE of 24.19% without any interface treatment and weak size dependence. A remarkable PCE of 22.63% is obtained even for a 1.004-cm(2) device. Importantly, the strategy shows good universality and significantly promotes the long-term stability of the pero-SCs based on the classical doped Spiro-OMeTAD.
|
|
| 16. |
- Zhu, Can, et al.
(författare)
-
Tuning the electron-deficient core of a non-fullerene acceptor to achieve over 17% efficiency in a single-junction organic solar cell
- 2020
-
Ingår i: Energy & Environmental Science. - : ROYAL SOC CHEMISTRY. - 1754-5692 .- 1754-5706. ; 13:8, s. 2459-2466
-
Tidskriftsartikel (refereegranskat)abstract
- Finding effective molecular design strategies to enable efficient charge generation and small energy loss is among the long-standing challenges in developing high performance non-fullerene organic solar cells (OSCs). Recently, we reported Y-series non-fullerene acceptors with an electron-deficient-core-based fused structure (typically Y6), opening a new door to achieve high external quantum efficiency (∼80%) while maintaining low energy loss (∼0.57 eV). On this basis, further reducing the energy losses and ultimately improving the performance of OSCs has become a research hotspot. In this paper, we design and synthesize a new member of the Y-series acceptor family, Y18, which adopts a fused benzotriazole segment with unique luminescence properties as its electron-deficient core. Compared to Y6, the benzotriazole-based acceptor Y18 exhibits extended optical absorption and higher voltage. Consequently, the device delivers a promising power conversion efficiency of 16.52% with a very low energy loss of 0.53 eV. Further device optimization by exploiting a ternary blend strategy allowed us to achieve a high efficiency of 17.11% (certified as 16.76% by NREL). Y18 may become one of the most important candidate materials for its broader absorption spectra and higher voltage of Y18 (compared to Y6) in the OSCs field.
|
|
| 17. |
- Almora, Osbel, et al.
(författare)
-
Device Performance of Emerging Photovoltaic Materials (Version 1)
- 2020
-
Ingår i: Advanced Energy Materials. - : Wiley. - 1614-6832 .- 1614-6840. ; 11:11
-
Tidskriftsartikel (refereegranskat)abstract
- Emerging photovoltaics (PVs) focus on a variety of applications complementing large scale electricity generation. Organic, dye-sensitized, and some perovskite solar cells are considered in building integration, greenhouses, wearable, and indoor applications, thereby motivating research on flexible, transparent, semitransparent, and multi-junction PVs. Nevertheless, it can be very time consuming to find or develop an up-to-date overview of the state-of-the-art performance for these systems and applications. Two important resources for recording research cells efficiencies are the National Renewable Energy Laboratory chart and the efficiency tables compiled biannually by Martin Green and colleagues. Both publications provide an effective coverage over the established technologies, bridging research and industry. An alternative approach is proposed here summarizing the best reports in the diverse research subjects for emerging PVs. Best performance parameters are provided as a function of the photovoltaic bandgap energy for each technology and application, and are put into perspective using, e.g., the Shockley–Queisser limit. In all cases, the reported data correspond to published and/or properly described certified results, with enough details provided for prospective data reproduction. Additionally, the stability test energy yield is included as an analysis parameter among state-of-the-art emerging PVs.
|
|
| 18. |
- Chen, Xian-Kai, et al.
(författare)
-
A unified description of non-radiative voltage losses in organic solar cells
- 2021
-
Ingår i: Nature Energy. - : Springer Nature. - 2058-7546. ; 6:8, s. 799-806
-
Tidskriftsartikel (refereegranskat)abstract
- Organic solar cells based on non-fullerene acceptors have enabled high efficiencies yet their charge dynamics and its impact on the photovoltaic parameters are not fully understood. Now, Chen et al. provide a general description of non-radiative voltage losses in both fullerene and non-fullerene solar cells. Recent advances in organic solar cells based on non-fullerene acceptors (NFAs) come with reduced non-radiative voltage losses (Delta V-nr). Here we show that, in contrast to the energy-gap-law dependence observed in conventional donor:fullerene blends, the Delta V-nr values in state-of-the-art donor:NFA organic solar cells show no correlation with the energies of charge-transfer electronic states at donor:acceptor interfaces. By combining temperature-dependent electroluminescence experiments and dynamic vibronic simulations, we provide a unified description of Delta V-nr for both fullerene- and NFA-based devices. We highlight the critical role that the thermal population of local exciton states plays in low-Delta V-nr systems. An important finding is that the photoluminescence yield of the pristine materials defines the lower limit of Delta V-nr. We also demonstrate that the reduction in Delta V-nr (for example, <0.2 V) can be obtained without sacrificing charge generation efficiency. Our work suggests designing donor and acceptor materials with high luminescence efficiency and complementary optical absorption bands extending into the near-infrared region.
|
|
| 19. |
- Fan, Qunping, 1989, et al.
(författare)
-
Fluorinated Photovoltaic Materials for High-Performance Organic Solar Cells
- 2019
-
Ingår i: Chemistry - An Asian Journal. - : Wiley. - 1861-471X .- 1861-4728. ; 14:18, s. 3085-3095
-
Forskningsöversikt (refereegranskat)abstract
- Over the past decade, organic solar cells (OSCs) have achieved a dramatic boost in their power conversion efficiencies from about 6 % to over 16 %. In addition to developments in device engineering, innovative photovoltaic materials, especially fluorinated donors and acceptors, have become the dominant factor for improved device performance. This minireview highlights fluorinated photovoltaic materials that enable efficient OSCs. Impressive OSCs have been obtained by developing some important molds of fluorinated donor and acceptor systems. The molecular design strategy and the matching principle of fluorinated donors and acceptors in OSCs are discussed. Finally, a concise summary and outlook are presented for advances in fluorinated materials to realize the practical application of OSCs.
|
|
| 20. |
- He, Youjun, et al.
(författare)
-
Poly(4,8-bis(2-ethylhexyloxy)benzo[1,2-b:4,5-b ]dithiophene vinylene): Synthesis, Optical and Photovoltaic Properties
- 2010
-
Ingår i: JOURNAL OF POLYMER SCIENCE PART A-POLYMER CHEMISTRY. - : John Wiley and Sons, Ltd. - 0887-624X .- 1099-0518. ; 48:8, s. 1822-1829
-
Tidskriftsartikel (refereegranskat)abstract
- A new benzodithiophene (BDT)-based polymer, poly(4,8-bis(2-ethylhexyloxy)benzo[1,2-b:4,5-b]dithiophene vinylene) (PBDTV), was synthesized by Pd-catalyzed Stille-coupling method. The polymer is soluble in common organic solvents and possesses high thermal stability. PBDTV film shows a broad absorption band covering from 350 nm to 618 nm, strong photoluminescence peaked at 545 nm and high hole mobility of 4.84 x 10(-3) cm(2)/Vs. Photovoltaic properties of PBDTV were studied by fabricating the polymer solar cells based on PBDTV as donor and PC70BM as acceptor. With the weight ratio of PBDTV: PC70BM of 1:4 and the active layer thickness of 65 nm, the power conversion efficiency of the device reached 2.63% with V-oc = 0.71 V, I-sc = 6.46 mA/cm(2), and FF = 0.57 under the illumination of AM1.5, 100 mW/cm(2).
|
|
| 21. |
- Liu, Wei, et al.
(författare)
-
A-pi-A structured non-fullerene acceptors for stable organic solar cells with efficiency over 17%
- 2022
-
Ingår i: Science in China Series B. - : SCIENCE PRESS. - 1674-7291 .- 1869-1870. ; 65:7, s. 1374-1382
-
Tidskriftsartikel (refereegranskat)abstract
- With the development of photovoltaic materials, especially the small molecule acceptors (SMAs), organic solar cells (OSCs) have made breakthroughs in power conversion efficiencies (PCEs). However, the stability of high-performance OSCs remains a critical challenge for future technological applications. To tackle the inherent instability of SMA materials under the ambient conditions, much effort has been made to improve OSCs stability, including device modification and new materials design. Here we proposed a new electron acceptor design strategy and developed a "quasi-macromolecule" (QM) with an A-pi-A structure, where the functionalized pi-bridge is used as a linker between two SMAs (A), to improve the long-term stability without deteriorating device efficiencies. Such type of QMs enables excellent synthetic flexibility to modulate their optical/electro-chemical properties, crystallization and aggregation behaviors by changing the A and pi units. Moreover, QMs possess a unique long conjugated backbone combining high molecular weight over 3.5 kDa with high purity. Compared with the corresponding SMA BTP-4F-OD (Y6-OD), the devices based on newly synthesized A-pi-A type acceptors QM1 and QM2 could exhibit better device stability and more promising PCEs of 17.05% and 16.36%, respectively. This kind of "molecular-framework" (A-pi-A) structure provides a new design strategy for developing high-efficiency and -stability photovoltaic materials.
|
|
| 22. |
- Ma, Qing, et al.
(författare)
-
Promoting charge separation resulting in ternary organic solar cells efficiency over 17.5%
- 2020
-
Ingår i: Nano Energy. - : ELSEVIER. - 2211-2855 .- 2211-3282. ; 78
-
Tidskriftsartikel (refereegranskat)abstract
- Ternary blend has been an effective strategy for achieving high efficiency in organic solar cells (OSCs). Herein, a non-fullerene small molecule acceptor (C8-DTC) was synthesized and added to the PM6: Y6 system as a third component. By adding 10% of C8-DTC as the second acceptor in the PM6:Y6 system, an impressive power conversion efficiency of 17.52% was achieved with simultaneously increased open-circuit voltage, short-circuit current-density, and fill factor. The reduced voltage loss was due to the lowered non-radiative recombination loss in comparison with the binary device. It was also found that a small amount of C8-DTC in the PM6:Y6 blend resulted in enhanced charge separation and charge transport by providing possible extra channels of hole extraction. And the ternary system formed a good phase separation and favored bi-continuous transport network, which is more conducive to balance the electron and hole transport. The results indicate that the ternary system formed by C8-DTC as the third component is an effective method to improve the performance of the PM6:Y6 based OSCs.
|
|
| 23. |
- Su, Yueling, et al.
(författare)
-
High-efficiency organic solar cells processed from a halogen-free solvent system
- 2023
-
Ingår i: Science in China Series B. - : SCIENCE PRESS. - 1674-7291 .- 1869-1870. ; 66:8, s. 2380-2388
-
Tidskriftsartikel (refereegranskat)abstract
- The use of non-halogenated solvents for the green manufacture of high-efficiency organic solar cells (OSCs) is important for their future application. However, the power conversion efficiency (PCE) of the non-halogenated solvent processed OSCs is generally lower than their halogenated counterpart due to the poor film microstructure caused by the solubility issue. Herein, we propose a halogen-free solvent system to optimize film microstructure of the photovoltaic blend based on the polymer donor D18 and small-molecule acceptor (SMA) L8-BO towards high-efficiency OSCs. The solvent system is consisted of a main solvent carbon disulfide and an additive paraxylene, where the former ensures the good solution-processability and promotes the solution aggregation of L8-BO, and the latter can finely control the phase-separation process by selectively dissolving the SMA. This solvent combination robustly produces a high-quality active layer, i.e., the bicontinuous networks of donor and acceptor with nano-sized phase-separation and strong & pi;-& pi; stacking. With the effective charge generation, transport and collection, the resulting device from the non-halogenated solvent system shows a high PCE of 17.50%, which is comparable to that of the device prepared from the halogenated solvent chloroform (ca. 17.11%). This article proposes a new strategy for the green fabrication of high-efficiency OSCs to accelerate their industrialization.
|
|
| 24. |
- Tang, Ailing, et al.
(författare)
-
Simultaneously Achieved High Open-Circuit Voltage and Efficient Charge Generation by Fine-Tuning Charge-Transfer Driving Force in Nonfullerene Polymer Solar Cells
- 2018
-
Ingår i: Advanced Functional Materials. - : WILEY-V C H VERLAG GMBH. - 1616-301X .- 1616-3028. ; 28:6
-
Tidskriftsartikel (refereegranskat)abstract
- To maximize the short-circuit current density (J(SC)) and the open circuit voltage (V-OC) simultaneously is a highly important but challenging issue in organic solar cells (OSCs). In this study, a benzotriazole-based p-type polymer (J61) and three benzotriazole-based nonfullerene small molecule acceptors (BTA1-3) are chosen to investigate the energetic driving force for the efficient charge transfer. The lowest unoccupied molecular orbital (LUMO) energy levels of small molecule acceptors can be fine-tuned by modifying the end-capping units, leading to high V-OC (1.15-1.30 V) of OSCs. Particularly, the LUMO energy level of BTA3 satisfies the criteria for efficient charge generation, which results in a high V-OC of 1.15 V, nearly 65% external quantum efficiency, and a high power conversion efficiency (PCE) of 8.25%. This is one of the highest V-OC in the high-performance OSCs reported to date. The results imply that it is promising to achieve both high J(SC) and V-OC to realize high PCE with the carefully designed nonfullerene acceptors.
|
|
| 25. |
- Yang, Yi, et al.
(författare)
-
Solution-Processable Organic Molecule with Triphenylamine Core and Two Benzothiadiazole-Thiophene Arms for Photovoltaic Application
- 2010
-
Ingår i: JOURNAL OF PHYSICAL CHEMISTRY C. - : American Chemical Society (ACS). - 1932-7447 .- 1932-7455. ; 114:8, s. 3701-3706
-
Tidskriftsartikel (refereegranskat)abstract
- A new solution-processable biarmed organic molecule With triphenylamine (TPA) core and benzothiadiazole-hexylthiophene (BT-HT) arms, B(TPA-BT-HT), has been synthesized by a Heck reaction, and characterized by UV-vis absorption, cyclic voltammetry, and theoretical calculation. Photovoltaic properties of B(TPA-BT-HT) as light-harvesting and electron-donating material in organic solar cells (OSCs), with [6,6]-phenyl-C61-butyric acid methyl ester (PC60BM) or [6,6]-phenyl-C71-butyric acid methyl ester (PC70BM) as acceptors, were systematically investigated. The performance of the OSCs varied significantly with B(TPA-BT-HT)/fullerene weight ratio, active layer thickness, and solvents Used For spin-coating the active layer. The optimized device with the B(TPA-BT-HT)/PC70BM weight ratio of 1:2 and a thickness of 55 nm with the active layer spin-coated from DCB solution Shows a power conversion efficiency of 1.96% with a short-circuit current density of 5.50 mA/cm(2) and in open-circuit voltage of 0.96 V under (lie illumination of AM 1.5, 100 mw/cm(2).
|
|
