| 1. |
- Hörmann, Ulrich, et al.
(författare)
-
Voc from a Morphology Point of View : the Influence of Molecular Orientation on the Open Circuit Voltage of Organic Planar Heterojunction Solar Cells
- 2014
-
Ingår i: Journal of physical chemistry C. - : American Chemical Society (ACS). - 1932-7455 .- 1932-7447. ; 118:46, s. 26462-26470
-
Tidskriftsartikel (refereegranskat)abstract
- The film morphology and device performance of planar heterojunctionsolar cells based on the molecular donor material α-sexithiophene (6T) are investigated.Planar heterojunctions of 6T with two different acceptor molecules, the C60 fullerene anddiindenoperylene (DIP), have been prepared. The growth temperature of the 6T bottomlayer has been varied between room temperature and 100 °C for each acceptor. By meansof X-ray diffraction and X-ray absorption, we show that the crystallinity and the molecularorientation of 6T is influenced by the preparation conditions and that the 6T filmtemplates the growth of the subsequent acceptor layer. These structural changes areaccompanied by changes in the characteristic parameters of the correspondingphotovoltaic cells. This is most prominently observed as a shift of the open circuitvoltage (Voc): In the case of 6T/C60 heterojunctions, Voc decreases from 0.4 to 0.3 V,approximately, if the growth temperature of 6T is increased from room temperature to 100°C. By contrast, Voc increases from about 1.2 V to almost 1.4 V in the case of 6T/DIP solarcells under the same conditions. We attribute these changes upon substrate heating toincreased recombination in the C60 case while an orientation dependent intermolecular coupling seems to change the origin of the photovoltaic gap in the DIP case.
|
|
| 2. |
- Opitz, Andreas, et al.
(författare)
-
Organic heterojunctions : Contact-induced molecular reorientation, interface states, and charge redistribution
- 2016
-
Ingår i: Scientific Reports. - : Nature Publishing Group. - 2045-2322. ; 6
-
Tidskriftsartikel (refereegranskat)abstract
- We reveal the rather complex interplay of contact-induced re-orientation and interfacial electronic structure-in the presence of Fermi-level pinning-at prototypical molecular heterojunctions comprising copper phthalocyanine (H16CuPc) and its perfluorinated analogue (F16CuPc), by employing ultraviolet photoelectron and X-ray absorption spectroscopy. For both layer sequences, we find that Fermi-level (E-F) pinning of the first layer on the conductive polymer substrate modifies the work function encountered by the second layer such that it also becomes E-F-pinned, however, at the interface towards the first molecular layer. This results in a charge transfer accompanied by a sheet charge density at the organic/organic interface. While molecules in the bulk of the films exhibit upright orientation, contact formation at the heterojunction results in an interfacial bilayer with lying and co-facial orientation. This interfacial layer is not EF-pinned, but provides for an additional density of states at the interface that is not present in the bulk. With reliable knowledge of the organic heterojunction's electronic structure we can explain the poor performance of these in photovoltaic cells as well as their valuable function as charge generation layer in electronic devices.
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
- Belova, Valentina, et al.
(författare)
-
Evidence for Anisotropic Electronic Coupling of Charge Transfer States in Weakly Interacting Organic Semiconductor Mixtures
- 2017
-
Ingår i: Journal of the American Chemical Society. - : American Chemical Society (ACS). - 0002-7863 .- 1520-5126. ; 139:25, s. 8474-8486
-
Tidskriftsartikel (refereegranskat)abstract
- We present a comprehensive investigation of the charge-transfer (CT) effect in weakly interacting organic semiconductor mixtures. The donor-acceptor pair diindenoperylene (DIP) and N,N′-bis(2-ethylhexyl)-1,7-dicyanoperylene-3,4/9,10-bis(dicarboxyimide) (PDIR-CN2) has been chosen as a model system. A wide range of experimental methods was used in order to characterize the structural, optical, electronic, and device properties of the intermolecular interactions. By detailed analysis, we demonstrate that the partial CT in this weakly interacting mixture does not have a strong effect on the ground state and does not generate a hybrid orbital. We also find a strong CT transition in light absorption as well as in photo- and electroluminescence. By using different layer sequences and compositions, we are able to distinguish electronic coupling in-plane vs out-of-plane and, thus, characterize the anisotropy of the CT state. Finally, we discuss the impact of CT exciton generation on charge-carrier transport and on the efficiency of photovoltaic devices.
|
|
| 6. |
- Beyer, Paul, et al.
(författare)
-
Fermi level pinned molecular donor/acceptor junctions : Reduction of induced carrier density by interfacial charge transfer complexes
- 2020
-
Ingår i: Journal of Materials Chemistry C. - : Royal Society of Chemistry (RSC). - 2050-7534 .- 2050-7526. ; 8:43, s. 15199-15207
-
Tidskriftsartikel (refereegranskat)abstract
- Increased hole density in an electron donor-type organic semiconductor can be achieved by deposition of a strong acceptor-type molecular layer on top, and has been shown to enable adjusting the carrier density in organic field effect transistors (OFETs). This interfacial charge transfer is due to simultaneous Fermi level (EF) pinning of the donor's highest occupied level and the acceptor's lowest unoccupied level. Here, we investigate the electrical properties of such an EF-pinned junction formed by diindenoperylene (DIP, as donor) and hexafluoro-tetracyano-naphthoquinodimethane (F6, as acceptor) in OFETs, as well as its electronic properties by photoelectron spectroscopy and electrostatic modelling. We find that, in addition to the EF-pinning induced integer charge transfer across the interface, DIP and F6 form charge transfer complexes (CPXs) at their junction. The molecularly thin CPX interlayer acts as insulator and significantly reduces the density of carriers induced on either side of the junction, compared to a scenario without such an interlayer. CPX formation is thus unfavourable for the effectiveness of controlling carrier density at molecular donor/acceptor junctions by EF-pinning. This journal is
|
|
| 7. |
- Blazinic, Vanja, et al.
(författare)
-
Impact of intentional photo-oxidation of a donor polymer and PC70BM on solar cell performance
- 2019
-
Ingår i: Physical Chemistry, Chemical Physics - PCCP. - : Royal Society of Chemistry. - 1463-9076 .- 1463-9084. ; 21, s. 22259-22271
-
Tidskriftsartikel (refereegranskat)abstract
- A short lifetime is the main factor hindering the wider implementation of low-cost organic photovoltaics in large-area and outdoor applications. Ingress of oxygen and water vapour through non-ideal encapsulation layers is a known cause of degradation for polymer/fullerene based solar cells. To better understand the origin of this performance degradation, we study the effect of intentional exposure of the photo-active layer to simulated sunlight (AM1.5) in air both on the solar cell performance and on the molecular semiconductor materials. Cathode-free thin films of a blend of the electron donor polymer poly[2,3-bis-(3-octyloxyphenyl)quinoxaline-5,8-diyl-alt-thiophene-2,5-diyl] (TQ1) and the electron acceptor fullerene derivative [6,6]-phenyl-C70-butyric acid methyl ester (PC70BM) were exposed to simulated sunlight in air. Fourier-transform infrared spectra demonstrate the formation of carbonyl photo-oxidation products in the blend films, as well as in the pristine polymer and fullerene films. Solar cells prepared with photo-oxidized active layers show increasingly degraded electrical performance (lower short circuit current, open circuit voltage and fill factor) with increasing exposure time. The increased diode ideality factor indicates that trap-assisted recombination hinders device operation after exposure. The external quantum efficiency decreases drastically with increasing exposure time over the whole photon energy range, while the UV-vis absorption spectra of the blend films only show a mild photo-induced bleaching. This demonstrates that not only the photo-induced degradation of the solar cell performance is not predominantly caused by the loss in light absorption, but charge transport and collection are also hampered. This is explained by the fact that photo-oxidation of PC70BM causes bonds in its conjugated cage to break, as evidenced by the decreased ∏* intensity in C1s-NEXAFS spectra of PC70BM films. This degradation of unoccupied states of PC70BM will hinder the transport of photo-generated electrons to the electrode. Surface photovoltage spectroscopy gives direct evidence for gap states at the surface of a PC70BM film, formed after 2 hours of exposure and resulting in upward band bending at the PC70BM/air surface. These observations indicate that the photo-oxidation of PC70BM is likely to be the main cause of the performance degradation observed when the photoactive layer of a TQ1:PC70BM solar cell is intentionally exposed to light in air.
|
|
| 8. |
|
|
| 9. |
- Demichev, Vadim, et al.
(författare)
-
A time-resolved proteomic and prognostic map of COVID-19
- 2021
-
Ingår i: Cell Systems. - : Elsevier BV. - 2405-4712 .- 2405-4720. ; 12:8, s. 780-794.e7
-
Tidskriftsartikel (refereegranskat)abstract
- COVID-19 is highly variable in its clinical presentation, ranging from asymptomatic infection to severe organ damage and death. We characterized the time-dependent progression of the disease in 139 COVID-19 inpatients by measuring 86 accredited diagnostic parameters, such as blood cell counts and enzyme activities, as well as untargeted plasma proteomes at 687 sampling points. We report an initial spike in a systemic inflammatory response, which is gradually alleviated and followed by a protein signature indicative of tissue repair, metabolic reconstitution, and immunomodulation. We identify prognostic marker signatures for devising risk-adapted treatment strategies and use machine learning to classify therapeutic needs. We show that the machine learning models based on the proteome are transferable to an independent cohort. Our study presents a map linking routinely used clinical diagnostic parameters to plasma proteomes and their dynamics in an infectious disease.
|
|
| 10. |
- Grob, Stefan, et al.
(författare)
-
Solvent vapor annealing on perylene-based organic solar cells
- 2015
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry. - 2050-7488 .- 2050-7496. ; 3:30, s. 15700-15709
-
Tidskriftsartikel (refereegranskat)abstract
- Diindenoperylene (DIP) and tetraphenyldibenzoperiflanthene (DBP) are two commonly used donor materials in organic solar cell devices. Despite their structural similarities, DIP films are crystalline, exhibiting good charge and exciton transport, whereas DBP films are amorphous and have lower carrier mobility and a short exciton diffusion length. However, DBP reveals a distinctly higher absorption due to the lying orientation of its transition dipole moments. In this paper, we investigate the influence of solvent vapor annealing (SVA) on the solar cell performance of both materials. In general, SVA induces a partial re-solubilization of the material leading to enhanced crystallinity of the treated layer. For DBP, extended annealing times result in a strong aggregation of the molecules, creating inhomogeneous layers unfavorable for solar cells. However, in DIP cells, SVA leads to an increase in fill factor (FF) and also a slight increase in short-circuit current density (JSC) due to interface roughening. The best results are obtained by combining solvent vapor annealed DIP layers with strongly absorbing DBP and C-70 on top. Through this device architecture, we obtain the same increase in FF in addition to a higher gain in J(SC), elevating the power conversion efficiency by a factor of 1.2 to more than 4%.
|
|
| 11. |
- Hansson, Rickard, 1987-
(författare)
-
Materials and Device Engineering for Efficient and Stable Polymer Solar Cells
- 2017
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Polymer solar cells form a promising technology for converting sunlight into electricity, and have reached record efficiencies over 10% and lifetimes of several years. The performance of polymer solar cells depends strongly on the distribution of electron donor and acceptor materials in the active layer. To achieve longer lifetimes, degradation processes in the materials have to be understood. In this thesis, a set of complementary spectroscopy and microscopy techniques, among which soft X-ray techniques have been used to determine the morphology of polymer:fullerene based active layers. We have found that the morphology of TQ1:PC70BM films is strongly influenced by the processing solvent and the use of solvent additives. We have also found, by using soft X-ray techniques, that not only the light-absorbing polymer TQ1, but also the fullerene is susceptible to photo-degradation in air. Moreover, the fullerene degradation is accelerated in the presence of the polymer. Additionally, this thesis addresses the role of the interfacial layers for device performance and stability. The commonly used hole transport material PEDOT:PSS has the advantage of being solution processable at room temperature, but this layer is also known to contribute to the device degradation. We have found that low-temperature processed NiOx is a promising alternative to PEDOT:PSS, leading to improved device performance. Even for encapsulated polymer solar cells, some photo-induced degradation of the electrical performance is observed and is found to depend on the nature of the hole transport material. We found a better initial stability for solar cells with MoO3 hole transport layers than with PEDOT:PSS. In the pursuit of understanding the initial decrease in electrical performance of PEDOT:PSS-based devices, simulations were performed, from which a number of degradation sources could be excluded.
|
|
| 12. |
- Hansson, Rickard
(författare)
-
Morphology and material stability in polymer solar cells
- 2015
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Polymer solar cells are promising in that they are inexpensive to produce, and due to their mechanical flexibility have the potential for use in applications not possible for more traditional types of solar cells. The performance of polymer solar cells depends strongly on the distribution of electron donor and acceptor material in the active layer. Understanding the connection between morphology and performance as well as how to control the morphology, is therefore of great importance. Furthermore, improving the lifetime of polymer solar cells has become at least as important as improving the efficiency. In this thesis, the relation between morphology and solar cell performance is studied, and the material stability for blend films of the thiophene-quinoxaline copolymer TQ1 and the fullerene derivatives PCBM and PC70BM. Atomic force microscopy (AFM) and scanning transmission X-ray microscopy (STXM) are used to investigate the lateral morphology, secondary ion mass spectrometry (SIMS) to measure the vertical morphology and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy to determine the surface composition. Lateral phase-separated domains are observed whose size is correlated to the solar cell performance, while the observed TQ1 surface enrichment does not affect the performance. Changes to the unoccupied molecular orbitals as a result of illumination in ambient air are observed by NEXAFS spectroscopy for PCBM, but not for TQ1. The NEXAFS spectrum of PCBM in a blend with TQ1 changes more than that of pristine PCBM. Solar cells in which the active layer has been illuminated in air prior to the deposition of the top electrode exhibit greatly reduced electrical performance. The valence band and absorption spectrum of TQ1 is affected by illumination in air, but the effects are not large enough to account for losses in solar cell performance, which are mainly attributed to PCBM degradation at the active layer surface.
|
|
| 13. |
|
|
| 14. |
- Slevogt, Hortense, et al.
(författare)
-
CEACAM1 inhibits Toll-like receptor 2-triggered antibacterial responses of human pulmonary epithelial cells
- 2008
-
Ingår i: Nature Immunology. - : Springer Science and Business Media LLC. - 1529-2908 .- 1529-2916. ; 9:11, s. 1270-1278
-
Tidskriftsartikel (refereegranskat)abstract
- Although Moraxella catarrhalis and Neisseria meningitidis are important human pathogens, they often colonize the human respiratory tract without causing overt clinical symptoms. Both pathogens express structurally unrelated proteins that share the ability to stimulate the adhesion molecule CEACAM1 expressed on human cells. Here we demonstrate that the interaction of CEACAM1 with ubiquitous surface protein A1 expressed on M. catarrhalis or with opacity-associated proteins on N. meningitidis resulted in reduced Toll-like receptor 2-initiated transcription factor NF-kappa B-dependent inflammatory responses of primary pulmonary epithelial cells. These inhibitory effects were mediated by tyrosine phosphorylation of the immunoreceptor tyrosine-based inhibitory motif of CEACAM1 and by recruitment of the phosphatase SHP-1, which negatively regulated Toll-like receptor 2-dependent activation of the phosphatidylinositol 3-OH kinase-Akt kinase pathway. Our results identify a CEACAM1-dependent immune-evasion strategy.
|
|
| 15. |
- Talyzin, Alexandr, 1969-, et al.
(författare)
-
Brodie vs Hummers graphite oxides for preparation of multi-layered materials
- 2017
-
Ingår i: Carbon. - : Elsevier. - 0008-6223 .- 1873-3891. ; 115, s. 430-440
-
Tidskriftsartikel (refereegranskat)abstract
- Graphite oxides synthesized by one and two step Brodie oxidation (BGO) and Hummers (HGO) methods were analyzed by a variety of characterization methods in order to evaluate the reasons behind the difference in their properties. It is found that the Brodie method results in a higher relative amount of hydroxyl groups and a more homogeneous overall distribution of functional groups over the planar surface of the graphene oxide flakes. The higher number of carbonyl and carboxyl groups in HGO, detected by several methods, including XPS, NMR and FTIR, unavoidably results in defects of the graphene "skeleton", holes and overall disruption of the carbon-carbon bond network, stronger deviation from planar flake shape and poor ordering of the graphene oxide layers. It is also suggested that functional groups in HGO are less homogeneously distributed over the flake surface, forming some nanometer-sized graphene areas. The presence of differently oxidized areas on the GO surface results in inhomogeneous solvation and hydration of HGO and effects of inter- and intra-stratification. The proposed interpretation of the data explains the higher mechanical strength of multi-layered BGO membranes/papers, which are also less affected by humidity changes, thus providing an example of a membrane property superior to that of HGO. (C) 2016 Published by Elsevier Ltd.
|
|
